2. Munters
  3. RPLP-1-V1
RPLP-1-V1

Munters RPLP-1-V1 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Munters RPLP-1-V1 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the Munters RPLP-1-V1?
    Where should the RPLP-1-V1 be placed?
    How should the RPLP-1-V1 be connected?
    Can the RPLP-1-V1 provide protection to devices other than controllers?
    What is the maximum current capacity of the RPLP-1-V1?
    What are the operating temperature and humidity ranges for the RPLP-1-V1?
    What are the dimensions of the RPLP-1-V1?
    Does the RPLP-1-V1 have an IP rating?
P/N: 112003
Ag/MIS/UmGb-2589-05/18 Rev 1.2
RPLP INSTALLATION
P/N: P-RPLP / C-RPLP
Place the Power Supply Lightning Protector close to the controller.
A proper ground must be supplied otherwise the protection will not be effective.
The side marked "INPUT" should be connected to the power source side. The side marked
"OUTPUT" should be connected to the power supply terminal side of the controller ONLY.
For example: If using a 24 VAC with the RPLP-1, then the voltage 24 VAC for the
solenoid should be wired from the "INPUT" unprotected side of the RPLR-1. This way any
interference caused by the solenoid will be filtered by the RPLP-1.
Protected and unprotected wires should not go through the same hole. Keep a distance of
at least 1 inch (2.5 cm) between protected and unprotected wires.
NOTE: The RPLP-1 is designed to provide protection ONLY to a controller. Make sure that devices such as
fans or motors operated by the controller do NOT obtain their power through the RPLP-1. Maximum current
through the RPLP-1 is 2.5 Amperes.
TECHNICAL SPECIFICATIONS
Power supply
Main voltage single phase 230 Vac / single phase 110 Vac 3 A
Main frequency 50/60 HZ
Ambient climate
Operating temperature range -10º to + 55º C
Storage temperature range -10º to + 70º C
Housing
Plastic housing with a screw on lid IP 56
Dimensions (LxWxH) 100 x 100 x 50 mm.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing as waste. The controller,
accessories and packaging should be sorted for environmental-
friendly recycling. The plastic components are labeled for categorized
recycling.
P/N: 112003
Ag/MIS/UmGb-2589-05/18 Rev 1.2
INSTALLATION
P/N: P-RPLP / C-RPLP
Place the Power Supply Lightning Protector close to the controller.
A proper ground must be supplied otherwise the protection will not be effective.
The side marked "INPUT" should be connected to the power source side. The side marked
"OUTPUT" should be connected to the power supply terminal side of the controller ONLY.
For example: If using a 24 VAC with the RPLP-1, then the voltage 24 VAC for the
solenoid should be wired from the "INPUT" unprotected side of the RPLR-1. This way any
interference caused by the solenoid will be filtered by the RPLP-1.
Protected and unprotected wires should not go through the same hole. Keep a distance of
at least 1 inch (2.5 cm) between protected and unprotected wires.
NOTE: The RPLP-1 is designed to provide protection ONLY to a controller. Make sure that devices such as
fans or motors operated by the controller do NOT obtain their power through the RPLP-1. Maximum current
through the RPLP-1 is 2.5 Amperes.
TECHNICAL SPECIFICATIONS
Power supply
Main voltage single phase 230 Vac / single phase 110 Vac 3 A
Main frequency 50/60 HZ
Ambient climate
Operating temperature range -10º to + 40º C
Storage temperature range -10º to + 70º C
Housing
Plastic housing with a screw on lid IP 56
Dimensions (LxWxH) 100 x 100 x 50 mm.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing as waste. The controller,
accessories and packaging should be sorted for environmental-
friendly recycling. The plastic components are labeled for categorized
recycling.
P/N: 112003
Ag/MIS/UmGb-2589-05/18 Rev 1.2
P/N: 112003
Ag/MIS/UmGb-2589-05/18 Rev 1.2
/