Revell 3015 Assembly Manual

Type
Assembly Manual
*
Version B
Version A
12
11
15
14
4
3
16
7
1
2
6
5 8
10
(Repeat for other side
using decal 9)
FINAL ASSEMBLY CONTINUED
4
DECAL PLACEMENT
5 USE HOUSEHOLD
THREAD FOR RIGGING
(NOT INCLUDED)
Kit 3015 - Page 4
Flat Dark Gray
Flat Gray
Flat Tan
Flat White
Orange
Semi Gloss Black
Brass
Flat Dark Red
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Vert foncé mat
Gris mat
Havane mat
Blanc mat
Orange
Noir satiné
Laiton
Rouge foncé mat
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star () to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile () pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* rifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
ROGER B. TANEY
USCG
CUTTER
KIT 3015 85301500200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (853015000200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* DECAL
* DECAL COMANIE
* REPEAT PROCEDURE
* R E P E T E Z L E P R O C E D E
* ASSEMBLY CAUTION
*ATTENTION D ASSEMBLEE
* OPTIONAL PARTS
* PIECES EN OPTION
The 327-foot endurance cutter Roger B. Taney
was in Pearl Harbor on December 7, 1941.
Among the first to fire back that morning, the
ship served escort duty throughout the war in
both the Atlantic and Pacific theaters. During
the Okinawa campaign in 1945, the Taney came
under air attacks more than 250 times-surviving
some of the heaviest suicide attacks of the
war. The Taney also served in the Korean and
Vietnam conflicts. In peacetime, the ship has
served as an ocean station vessel, a search and
rescue ship, and on Alaskan fisheries patrol.
The USCGC Taney is now stationed in Virginia,
as a unit of the fifth Coast Guard district.
Your Revell model features a detailed deck with
8 depth charge throwers, 2 roller racks, life rafts
and boats, davits, searchlights, railings, engraved
hull detail, two-40mm guns, four-20mm guns, 5"
elevating gun in rotating turret, radar, antennas,
display stand and decals with authentic markings.
THREAD
CUT OUT PAPER FLAG
DECALS AND WRAP
AROUND THREAD RIG-
GING LINE. CAREFULLY
CEMENT TOGETHER
FLAG DECALS
*
*
*
*
*
*
*
*
*
* *
*
* *
*
*
HULL ASSEMBLY
1
MAIN DECK ASSEMBLY
2FINAL ASSEMBLY
4
UPPER DECK ASSEMBLY
3
Kit 3015 - Page 3
Kit 3015 - Page 2
1
RIGHT HULL HALF
FLAT WHITE
(SHADED AREA FLAT DARK RED)
2
LEFT HULL HALF
FLAT DARK GRAY
(SHADED AREA FLAT DARK RED)
5
5” GUN
SEMI GLOSS BLACK
6
TURRET
FLAT WHITE
7
FORWARD
MAIN DECK
FLAT TAN
8
LEFT ANCHOR
FLAT WHITE
10
RIGHT ANCHOR
FLAT WHITE
12
DEPTH CHARGES
FLAT DARK GRAY (SHOWN
IN PLACE)
12
DEPTH CHARGES
FLAT DARK GRAY (SHOWN
IN PLACE)
12
DEPTH CHARGES
FLAT DARK GRAY
15
FORWARD
SUPERSTRUCTURE
DECK
FLAT WHITE
16
RIGHT BRIDGE SIDE
FLAT WHITE
20
MAIN
SUPERSTRUCTURE
DECK
FLAT GRAY
17
LEFT BRIDGE
SIDE
FLAT WHITE
21
BRIDGE DECK
FLAT GRAY
4
MAIN DECK
FLAT TAN
18
LEFT MAIN
SUPERSTRUCTURE
SIDE
FLAT WHITE
25
STACK DECK
FLAT GRAY
19
RIGHT MAIN
SUPERSTRUCTURE
SIDE
FLAT WHITE
3
RUDDER
FLAT DARK RED
3A
RUDDER RETAINER
6A
TURRET
RETAINER
11
WILD CAT BITT
SEMI GLOSS BLACK
22
BRIDGE
SHIELD
FLAT WHITE
28
SEARCH LIGHT
FLAT WHITE
23
RIGHT STACK
SUPERSTRUCTURE SIDE
FLAT WHITE
24
LEFT STACK
SUPERSTRUCTURE SIDE
FLAT WHITE
27
LEFT
SEARCHLIGHT
PLATFORM
FLAT WHITE
26
RIGHT
SEARCHLIGHT
PLATFORM
FLAT WHITE
13
RIGHT FORWARD
SUPERSTRUCTURE
HALF
FLAT WHITE
14
LEFT FORWARD
SUPERSTRUCTURE
HALF
FLAT WHITE
62
RIGHT BOAT
DAVIT
FLAT TAN
62
RIGHT BOAT DAVIT
FLAT TAN
60
CAPTAIN’S BOAT BOTTOM
FLAT WHITE
66
SEARCHLIGHT
PLATFORM
FLAT WHITE
66
SEARCHLIGHT
PLATFORM
FLAT WHITE
69
RADAR
ANTENNA
SEMI GLOSS BLACK
67
FORWARD MAST
FLAT TAN
68
FORWARD MAST YARD
FLAT TAN
70
REAR MAST
FLAT TAN
71
REAR MAST YARD
FLAT TAN
72
REAR MAST TOP CAP
FLAT WHITE
33
RADAR ROOM DECK
FLAT GRAY
29
REAR SUPERSTRUCTURE RAILING
FLAT WHITE
37
STACK CAP
SEMI GLOSS BLACK
30
RIGHT RADAR ROOM SIDE
FLAT WHITE
41
40MM GUN
PLATFORM
SEMI GLOSS
BLACK
61
LEFT BOAT DAVIT
FLAT TAN
61
LEFT BOAT DAVIT
FLAT TAN
31
LEFT RADAR
ROOM SIDE
FLAT WHITE
42
40MM GUN
SEMI GLOSS
BLACK
32
RADAR ROOM FRONT
FLAT WHITE
43
RANGE FINDER
SEMI GLOSS BLACK
40
TWIN 40MM
GUN TUB
FLAT WHITE
47
NAVIGATION GUN DIRECTOR
SEMI GLOSS BLACK
58
LIFE BOAT
FLAT WHITE
44
RANGE
FINDER BASE
FLAT WHITE
48
20MM GUN
SEMI GLOSS
BLACK
48
20MM
GUN
SEMI
GLOSS
BLACK
45
ROCKET LAUNCHER
FLAT DARK GRAY
49
LEFT DEPTH
CHARGE
RACK HALF
FLAT DARK GRAY
36
RIGHT STACK HALF
FLAT TAN
35
LEFT
STACK
HALF
FLAT TAN
50
RIGHT DEPTH
CHARGE RACK
HALF
FLAT DARK GRAY
46
LIFE RAFT
ORANGE
46
LIFE
RAFT
ORANGE
53
LEFT
PROPELLER
GUARD
FLAT WHITE
52
RIGHT
PROPELLER
GUARD
FLAT WHITE
51
STAND
SEMI GLOSS BLACK
54
PROPELLER
BRASS
63
DEPTH
CHARGE DAVITS
FLAT TAN
55
PROPELLER
SHAFT
FLAT DARK RED
56
BOAT BOOM
FLAT TAN
34
GUN DIRECTOR PLATFORM
FLAT WHITE
64
FLAG STAFF
FLAT TAN
57
LIFEBOAT
SEATS
FLAT TAN
38
TAJ TRUNK
FLAT TAN
65
JACK STAFF
FLAT TAN
59
CAPTAIN’S BOAT TOP
FLAT WHITE
39
WHIP
ANTENNAS
FLAT WHITE
SEMI GLOSS BLACK
61, 57, 58 and 62
(SHOWN IN PLACE)
49 and 50
(SHOWN IN PLACE)
*
*
*
*
*
*
*
*
*
*
*
* *
*
* *
*
*
HULL ASSEMBLY
1
MAIN DECK ASSEMBLY
2FINAL ASSEMBLY
4
UPPER DECK ASSEMBLY
3
Kit 3015 - Page 3
Kit 3015 - Page 2
1
RIGHT HULL HALF
FLAT WHITE
(SHADED AREA FLAT DARK RED)
2
LEFT HULL HALF
FLAT DARK GRAY
(SHADED AREA FLAT DARK RED)
5
5” GUN
SEMI GLOSS BLACK
6
TURRET
FLAT WHITE
7
FORWARD
MAIN DECK
FLAT TAN
8
LEFT ANCHOR
FLAT WHITE
10
RIGHT ANCHOR
FLAT WHITE
12
DEPTH CHARGES
FLAT DARK GRAY (SHOWN
IN PLACE)
12
DEPTH CHARGES
FLAT DARK GRAY (SHOWN
IN PLACE)
12
DEPTH CHARGES
FLAT DARK GRAY
15
FORWARD
SUPERSTRUCTURE
DECK
FLAT WHITE
16
RIGHT BRIDGE SIDE
FLAT WHITE
20
MAIN
SUPERSTRUCTURE
DECK
FLAT GRAY
17
LEFT BRIDGE
SIDE
FLAT WHITE
21
BRIDGE DECK
FLAT GRAY
4
MAIN DECK
FLAT TAN
18
LEFT MAIN
SUPERSTRUCTURE
SIDE
FLAT WHITE
25
STACK DECK
FLAT GRAY
19
RIGHT MAIN
SUPERSTRUCTURE
SIDE
FLAT WHITE
3
RUDDER
FLAT DARK RED
3A
RUDDER RETAINER
6A
TURRET
RETAINER
11
WILD CAT BITT
SEMI GLOSS BLACK
22
BRIDGE
SHIELD
FLAT WHITE
28
SEARCH LIGHT
FLAT WHITE
23
RIGHT STACK
SUPERSTRUCTURE SIDE
FLAT WHITE
24
LEFT STACK
SUPERSTRUCTURE SIDE
FLAT WHITE
27
LEFT
SEARCHLIGHT
PLATFORM
FLAT WHITE
26
RIGHT
SEARCHLIGHT
PLATFORM
FLAT WHITE
13
RIGHT FORWARD
SUPERSTRUCTURE
HALF
FLAT WHITE
14
LEFT FORWARD
SUPERSTRUCTURE
HALF
FLAT WHITE
62
RIGHT BOAT
DAVIT
FLAT TAN
62
RIGHT BOAT DAVIT
FLAT TAN
60
CAPTAIN’S BOAT BOTTOM
FLAT WHITE
66
SEARCHLIGHT
PLATFORM
FLAT WHITE
66
SEARCHLIGHT
PLATFORM
FLAT WHITE
69
RADAR
ANTENNA
SEMI GLOSS BLACK
67
FORWARD MAST
FLAT TAN
68
FORWARD MAST YARD
FLAT TAN
70
REAR MAST
FLAT TAN
71
REAR MAST YARD
FLAT TAN
72
REAR MAST TOP CAP
FLAT WHITE
33
RADAR ROOM DECK
FLAT GRAY
29
REAR SUPERSTRUCTURE RAILING
FLAT WHITE
37
STACK CAP
SEMI GLOSS BLACK
30
RIGHT RADAR ROOM SIDE
FLAT WHITE
41
40MM GUN
PLATFORM
SEMI GLOSS
BLACK
61
LEFT BOAT DAVIT
FLAT TAN
61
LEFT BOAT DAVIT
FLAT TAN
31
LEFT RADAR
ROOM SIDE
FLAT WHITE
42
40MM GUN
SEMI GLOSS
BLACK
32
RADAR ROOM FRONT
FLAT WHITE
43
RANGE FINDER
SEMI GLOSS BLACK
40
TWIN 40MM
GUN TUB
FLAT WHITE
47
NAVIGATION GUN DIRECTOR
SEMI GLOSS BLACK
58
LIFE BOAT
FLAT WHITE
44
RANGE
FINDER BASE
FLAT WHITE
48
20MM GUN
SEMI GLOSS
BLACK
48
20MM
GUN
SEMI
GLOSS
BLACK
45
ROCKET LAUNCHER
FLAT DARK GRAY
49
LEFT DEPTH
CHARGE
RACK HALF
FLAT DARK GRAY
36
RIGHT STACK HALF
FLAT TAN
35
LEFT
STACK
HALF
FLAT TAN
50
RIGHT DEPTH
CHARGE RACK
HALF
FLAT DARK GRAY
46
LIFE RAFT
ORANGE
46
LIFE
RAFT
ORANGE
53
LEFT
PROPELLER
GUARD
FLAT WHITE
52
RIGHT
PROPELLER
GUARD
FLAT WHITE
51
STAND
SEMI GLOSS BLACK
54
PROPELLER
BRASS
63
DEPTH
CHARGE DAVITS
FLAT TAN
55
PROPELLER
SHAFT
FLAT DARK RED
56
BOAT BOOM
FLAT TAN
34
GUN DIRECTOR PLATFORM
FLAT WHITE
64
FLAG STAFF
FLAT TAN
57
LIFEBOAT
SEATS
FLAT TAN
38
TAJ TRUNK
FLAT TAN
65
JACK STAFF
FLAT TAN
59
CAPTAIN’S BOAT TOP
FLAT WHITE
39
WHIP
ANTENNAS
FLAT WHITE
SEMI GLOSS BLACK
61, 57, 58 and 62
(SHOWN IN PLACE)
49 and 50
(SHOWN IN PLACE)
*
*
*
Version B
Version A
12
11
15
14
4
3
16
7
1
2
6
5 8
10
(Repeat for other side
using decal 9)
FINAL ASSEMBLY CONTINUED
4
DECAL PLACEMENT
5 USE HOUSEHOLD
THREAD FOR RIGGING
(NOT INCLUDED)
Kit 3015 - Page 4
Flat Dark Gray
Flat Gray
Flat Tan
Flat White
Orange
Semi Gloss Black
Brass
Flat Dark Red
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Vert foncé mat
Gris mat
Havane mat
Blanc mat
Orange
Noir satiné
Laiton
Rouge foncé mat
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star () to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile () pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* rifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
ROGER B. TANEY
USCG
CUTTER
KIT 3015 85301500200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (853015000200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* DECAL
* DECAL COMANIE
* REPEAT PROCEDURE
* R E P E T E Z L E P R O C E D E
* ASSEMBLY CAUTION
*ATTENTION D ASSEMBLEE
* OPTIONAL PARTS
* PIECES EN OPTION
The 327-foot endurance cutter Roger B. Taney
was in Pearl Harbor on December 7, 1941.
Among the first to fire back that morning, the
ship served escort duty throughout the war in
both the Atlantic and Pacific theaters. During
the Okinawa campaign in 1945, the Taney came
under air attacks more than 250 times-surviving
some of the heaviest suicide attacks of the
war. The Taney also served in the Korean and
Vietnam conflicts. In peacetime, the ship has
served as an ocean station vessel, a search and
rescue ship, and on Alaskan fisheries patrol.
The USCGC Taney is now stationed in Virginia,
as a unit of the fifth Coast Guard district.
Your Revell model features a detailed deck with
8 depth charge throwers, 2 roller racks, life rafts
and boats, davits, searchlights, railings, engraved
hull detail, two-40mm guns, four-20mm guns, 5"
elevating gun in rotating turret, radar, antennas,
display stand and decals with authentic markings.
THREAD
CUT OUT PAPER FLAG
DECALS AND WRAP
AROUND THREAD RIG-
GING LINE. CAREFULLY
CEMENT TOGETHER
FLAG DECALS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Revell 3015 Assembly Manual

Type
Assembly Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages