V-ZUG 5101000000 Installation guide

Page is loading ...

Installation instructions

Refrigerator Perfekt KP

Built-in SMS

J51010.050-0

1.5.13

These installation instructions apply to the model:

A Information on the necessary mains voltage, type of current and fuse protection can be taken from the identification plate.

A Before installing the appliance, adhere spacers A (included in the scope of delivery) to the hinge side. Secure the appliance to the

kitchen cabinet at the top and bottom with 2 × 2 chipboard screws from the pack.

Validity

Type Model no. Model

KP 51010 Perfect (door can be fitted with decor panel)

Electrical connections

Installation without ventilation grille (indirect ventilation)

* Allow a gap – at the top and bottom – less than the width of the appliance to ensure proper ventilation (sheets 5–13 in the technical

guide on kitchen planning and design KVS).

Shadow gaps alone – even if extended over several elements – are not sufficient.

The appliance can be built in with indirect ventilation (installation height SMS 10/6) or in the case of direct ventilation with

separate ventilation grilles (installation height SMS 11/6).

The appliance door does not have to be removed for the decor panel to be mounted.

A

1850 (SMS norm)

Positioned BELOW

also possible

Positioned ABOVE

Standard

Flush-mounted power socket, type 13

120

100

50

4/6

Niche 1270 =10/6

+2

0

Appliance 1268

2/6

105

min. 50

min. 200 cm²

Identification plate located

left next to salad crisper

Niche 550

Appliance 547

Niche 605

Appliance 572

Approx. 520

100˚

max. 4

538

345188

ø 10

49

1259

Decor panel

Ventilation

cross-section

10

5019 102 01275

Installation instructions

Refrigerator Perfekt KP

Built-in SMS

J51010.050-0

1.5.13

A Unscrew the door handle. Using a screwdriver, remove the handle inlay. Unscrew cross-

recessed head screws as they become visible.

A Drill through-holes in decor panel for handle screws.

A Unscrew the upper part of the decor frame. Loosen the screws of the lower part enough

so that you can pull it forward. Push the decor plate into the gap from above. Press the

decor frame down firmly and tighten the screws. Insert and tighten screws in the upper

part of the decor frame. Screw in the door handle and clip on the handle inlay.

A Set the thermostat to the «0» position if it is not intended that the appliance be used im-

mediately after installation.

Installation with ventilation grille (direct ventilation)

1 ventilation grille set* contains:

2 Ventilation grilles 63 mm × 547 mm B

2 Plinth rails 63 mm × 490 mm C

2 Fastening plates for appliance/niche top D

2 Self-tapping screws 3.5 × 9.5 E

2 Plate nuts for fastening plate/appliance F

2 Self-tapping screws 3.9 × 12 for fastening plate/niche G

4 Self-tapping screws for ventilation grille/appliance H

4 Cover caps for ventilation grille I

4 Wood screws for ventilation grille/niche J

4 Wood screws for plinth rail/niche K

* Ventilation grille set, white, art. no. H7.1842

Ventilation grille set, nero, art. no. H7.1843

Disassembling

door handle

11

5019 102 01275

Installation instructions

Refrigerator Perfekt KP

Built-in SMS

J51010.050-0

1.5.13

A Check the height, width and depth of the niche against the appliance's installation guidelines.

A Place plinth rails C right up to the side walls, place on the floor and, observing the 80 mm measurement, screw to the floor and the

side walls K.

A Secure the fastening plate D to the appliance with the plate nuts.

A Insert the plug into the mains socket. Put the appliance on the rails in the niche.

A Align the appliance in the niche so that it is flush at the front and secure the fastening plate to the niche G.

A Secure top and bottom ventilation grilles B to the appliance with self-tapping screws H. Then screw to the niche with the wood

screws J.

A Insert cover caps I in screw driver through-holes of ventilation grille.

Detail X

Detail Y

K

C

H

I

B

J

E

F

J

G

D

1850 (SMS norm)

120

100

105

2/6

Niche 1397 =11/6

+2

0

Appliance 1268

1270=10/6 1/121/12

X

Y

2/6

105

min. 50

Niche 605

490

80

50

80

63 63

31

~34

~50

12

5019 102 01275

V-ZUG 5101000000 Installation guide

V-ZUG 5101000000 Installation guide

in other languages

Related papers

Other documents