Installation instructions
Noblesse KNi Refrigerator
Built-in EURO 60
J51028.513-0
7.9.12
1
These installation instructions apply to model: 51028
➤ Information on the necessary mains voltage, type of current and fuse protection can be taken from the identification plate.
➤ Push the appliance into the niche. Secure to the cabinet with 1 screw (included in the scope of delivery) through each hinge. Then
secure the appliance to the cabinet at the top with 2 chipboard screws each (included in the scope of delivery) through the fixing bar.
➤ Operate the appliance in accordance with the operating instructions supplied.
➤ Ensure that the appliance is switched off if it is not intended that the appliance be used immediately after installation.
Validity
This appliance is considered to be suitable for use in countries having a warm damp equable climate (WDaE). It may also be
used in other countries. If used in warm damp equable climated countries, the appliance is to be supplied through a residual
current device (RCD) having a rated residual operating current not exceeding 30 mA.
General notes
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
If installing into combustible material, the guidelines and safety standards for low voltage installations and fire protection must
be strictly observed.
Electrical connections
Electrical connections must be carried out by suitably qualified personnel in accordance with the guidelines and safety
standards for low voltage installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. A
mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and socket
devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching are
permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and fault-
free operation.
After installation, live parts and cables with basic insulation must not be accessible.
Check old installations.
Installation
The door opening can be changed from right to left up until the point when the appliance is installed in the niche.
Installation instructions
Noblesse KNi Refrigerator
Built-in EURO 60
J51028.513-0
7.9.12
2
Built-in, integratable door
* Allow a gap – at the top and bottom – less than the width of the appliance to ensure proper ventilation
(sheets 5–13 in the technical guide on kitchen planning and design from the Swiss Kitchen Association (KVS)).
Shadow gaps alone – even if extended over several elements – are not sufficient.
a Niche overlap
bGap
w
➤ For door panel thickness greater than 19 mm, use hinge bolts supplied.
– This restricts the opening radius to a maximum of 90°.
2050 (SMS norm) flush-mounted power socket, «type 13»
Positioned ABOVE
standard
Positioned BELOW
also possible
120
100
Niche 1778 =14/6
+2
0
Appliance 1776
=
=
min. 50
min. 200 cm²
min. 200 cm²
Ventilation cross-section
*
Appliance 545
a
min. 4
b
min. 4
+2
0
Niche1778 =14/6
Door leaves
508
1270
a
16–20
16–20
Niche 560–568
Appliance 548
100˚
Niche 550
ca. 602
Filler strip H7.1756
(request when ordering
appliance)
max. 594
1270+a-b
2b
508+a-b
w
Width of element
600
A
Detail A
Door panels
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
V-ZUG 619 Installation guide
-
-
Whirlpool MWC-SL/60 User guide
-
-
-
-
-
V-ZUG 51047 Installation guide
-
V-ZUG 28A Installation guide
-
Other documents
-
3P Technik 1000500 Installation guide
-
Siemens CI24RP01/07 User manual
-
-
-
Siemens CI36BP01 User manual
-
Siemens CI24RP01AU/01 User manual
-
-
-
Bosch CIB36P01/05 Installation guide
-
De Dietrich DRS918JE User manual
