Ancona AN-4314 User manual

Ancona
Brand
Ancona
Model
AN-4314
Type
User manual

Ancona AN-4314 is a bathroom faucet that meets the standards of ASME A112.18.1, CSA B125.1, NSF 61-9, and is LISTED IAPMO/cUPC. The flow rate varies based on the water pressure (measured as pounds per square inch (PSI)):

  • at 20 PSI the flow rate is 4.5 gallons per minute (GPM)
  • at 60 PSI the flow rate is 3 GPM The product comes with a limited warranty and should be handled with care during installation to avoid damaging the stem, which could void the warranty.

Ancona AN-4314 is a bathroom faucet that meets the standards of ASME A112.18.1, CSA B125.1, NSF 61-9, and is LISTED IAPMO/cUPC. The flow rate varies based on the water pressure (measured as pounds per square inch (PSI)):

  • at 20 PSI the flow rate is 4.5 gallons per minute (GPM)
  • at 60 PSI the flow rate is 3 GPM The product comes with a limited warranty and should be handled with care during installation to avoid damaging the stem, which could void the warranty.
Isla Bathroom Faucet
Gather the necessary tools as shown below to complete the installation of this
faucet. Some may not be needed depending on the model of faucet you are
installing. Check with your local hardware store on the requirements of your
installation situation.
Tools:
PLUMBERS PUTTY
FLASHLIGHT
BASIN WRENCH
SAFETY GLASSES
SCREW DRIVER
PLIERS
CHANNELLOCKS ADJUSTABLE WRENCH
SEALED-TUBE
HEX-KEY TAPE
Connect to water supply lines with either
A 3 8 O D copper tubing ball nose
risers with the coupling nuts or
B 3 8 copper tubing no ball with
supplied tube head interior connector or
C IPS faucet connectors 1 2
Tighten connection with two wrench to prevent damage to tube body.
Be careful not to bend the stem as this will void the product warranty.
C
A . B .
C .
Helpful Information
Flow Rate Chart
Important
STANDARDS
ASME A112.18.1
CSA B125.1
NSF 61-9
LISTED IAPMO/cUPC
2016-06-20 MAAN4314-02
)
0
1.5
2
2.5
3
0 10 20 30 40 50 60 70 80
3.5
4
4.5
GPM
PSI
Installation Steps
Installation Size Map
Réunissez les outils nécessaires comme montrés ci-dessous, pour compléter
l'installation de ce robinet. Certains peuvent ne pas être requis, selon le modèle du
robinet que vous installez. Vérifiez avec votre quincaillerie locale sur les exigences
de votre situation d'installation.
Outils:
A . B .
C .
Information utile
Diagramme de débit
Important
MASTIC DE PLOMBIER LAMPE DE POCHE
CLÉ DE LAVABO
LUNETTES DE SÉCURITÉ TOURNEVIS
PINCES
PINCES MULTIPRISES CLÉ ANGLAISE
TUBE DE SCELLAGE
CLÉ HEXAGONALE
RUBAN À MESURER
Connectez à une ligne d'alimentation en eau
avec soit :
A 3/8'' O.D. tuyau de cuivre (clapet-bille à
tube plongeur avec les écrous
d'accouplement ou)
B 3/8'' tubes plongeurs (sans clapet-bille)
avec connecteur de tube de tête intérieur
C Connecteurs de robinet IPS (1/2'')
Serrez la connexion avec deux clés anglaises pour empêcher des
dommages au corps du tuyau.
Faites attention de ne pas plier la tige, puisque ceci annulera
la garantie du produit.
2016-0
6-20 MAAN4314-02
•
NORMES
ASME A112.18.1
CSA B125.1
NSF 61-9
ENREGISTRÉ IAPMO/cUPC
Robinet de salle
de bain Isla
0
1.5
2
2.5
3
0 10 20 30 40 50 60 70 80
3.5
4
4.5
GPM
PSI
Installation
Carte de dimension d'installation
Chaud
Froid
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Ancona AN-4314 User manual

Ancona
Brand
Ancona
Model
AN-4314
Type
User manual

Ancona AN-4314 is a bathroom faucet that meets the standards of ASME A112.18.1, CSA B125.1, NSF 61-9, and is LISTED IAPMO/cUPC. The flow rate varies based on the water pressure (measured as pounds per square inch (PSI)):

  • at 20 PSI the flow rate is 4.5 gallons per minute (GPM)
  • at 60 PSI the flow rate is 3 GPM The product comes with a limited warranty and should be handled with care during installation to avoid damaging the stem, which could void the warranty.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents