Symmons SLC-9612-STN-1.5 Installation guide

Origins

™



-0.5 0.5 gpm (1.9 L/min) aerator



-1.0 1.0 gpm (3.8 L/min) aerator



-G Grid drain



-STN Satin Nickel ﬁnish

Model Numbers

Two Handle Centerset Lavatory Faucet

Operation & Maintenance Manual

SLC-9610-1.5, SLC-9612-1.5

Two handle centerset lavatory faucet featuring a

4” mounting conguration. Includes ceramic cartridges,

1/2” IPS inlet connections, 50/50 drain assembly and

standard 1.5 gpm (5.7 L/min) aerator. Components made

from brass and nonmetallic materials plated in standard

polished chrome nish.

Speciﬁcation

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Compliance

c

Certied by

IAPMO R&T

Dimensions

Note: Dimensions subject to change without notice.

Modiﬁcations

Note: Append appropriate -sufx to model number.



SLC-9610-1.5

Origins Two Handle Centerset Lavatory Faucet

Less Rod



SLC-9612-1.5

Origins Two Handle Centerset Lavatory Faucet

-NSF/ANSI 372, NSF/ANSI 61.9

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm (5.7 L/min)

Measurements

A 8 7/8”, 225 mm

B 6”, 152 mm

C 4”, 102 mm

D 3 3/4”, 95 mm

E

Deck Thickness Ref.

Max. 1 1/4”, 32 mm

F

Hole Size

Min. Ø 1”, 25 mm

Max. Ø 1 1/8”, 29 mm

G

(2x) Hole Size

Min. Ø 1 1/8”, 29 mm

Max. Ø 1 1/4”, 32 mm

H 3 1/8”, 79 mm

I 1 5/8”, 41 mm

J 4 1/4”, 108 mm

K 1 3/4”, 44 mm

L 1/2-14 NPSM

CC

DD

EE

JJ

KK

GG

BB

AA

FF

HH

II

LL

2

*Note: Append -STN to part number for Satin Nickel

nish.

Replacement Parts

Item Description Part Number

A Lift Rod RL-219*

B

D

(2x) Handle Kit RL-220*

E Hot Cartridge RL-222H

F Cold Cartridge RL-222C

H Aerator

RL-240-1.5* (1.5)

RL-240-1.0* (1.0)

RL-240-0.5* (0.5)

I

J

Mounting Hardware RL-221

K 50/50 Drain Assembly

RL-223*

(SLC-9612-1.5)

L Grid Drain

P-26*

(SLC-9610-1.5)

Tools Required

Adjustable wrench

Allen wrench (3/32”)

Plumber putty

Plumber tape

PLUMBER

PUTTY

Parts Breakdown

K1

K2

K3

K8

K14

K4

K5

K6

K7

K9

K10

K13

K11

K12

B

K

D

C

E

F

G

H

I

J

A

L

3

G

I

2) Install mounting nuts (J) onto

1/2” IPS inlet connections on

faucet body (G). Using a wrench,

nish with one-half turn. DO NOT

overtighten.

1

G

J

If replacing an older faucet

ensure water supply is turned

OFF before removing, then

turn faucet control valve ON to

relieve water pressure.

1) Insert faucet body (G) through

mounting gasket (I) and sink

holes.

3) Seat ange (K2) into sink (K3 gas-

ket optional). Install gasket (K4),

washer (K5) and nut (K6) onto

ange (K2) from below sink, but

do not secure nut. Screw on tail

piece (K7) and hand tighten.

2

3

K2

K7

PLUMBER

PUTTY

OPTIONAL

K3

K4

K5

K6

4) Turn tail piece (K7) and ange

(K2) so pivot is facing toward

faucet. Pull assembly down into

drain hole. Secure hardware from

below sink. Install stopper (K1) in

the removable or non-removable

position.

2

3

K7

PIVOT

K2

K1

5) Attach inner washer (K8), pivot rod

(K9) and outer washer (K10) to tail-

piece (K7). Hand tighten nut (K11)

to secure pivot rod (K9).

K9

K7

1

K8

K10

K11

2

6) Connect lift rod (A) to clevis strap

(K13) and secure with thumb

screw (K14). Insert pivot rod

(K9) through spring clip (K12)

and clevis strap (K13). Secure

with spring clip (K12) and adjust

linkage if necessary.

3

4

K12

K9

K13

2

K14

K13

1

A

Installation

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621

Troubleshooting Chart

Finish is spotting.

Elements in water supply may cause

water staining on nish.

Clean nished trim area with a soft

cloth using mild soap and water or a

non-abrasive cleaner and then quickly

rinse with water.

7) Attach supply lines to 1/2” IPS inlet

connections on faucet body (G).

Using a wrench, nish with one half

turn. DO NOT overtighten.

Maintenance

1) Turn off water. Loosen and

remove handle set screw (D),

handle (B), nut (C) and old

cartridge (E or F).

6

5

3

4

1

2

B

C

D

F

2) Correctly align new cartridge (E

or F) and insert into faucet body

(G). Install and secure nut (C).

1

2

3

C

F

G

3) Replace handle (B) and reinstall set

screw (D). Tighten set screw.

G

8) Attach supply lines to shut-off

valves and hand tighten. Using a

wrench, nish with one-half turn.

DO NOT overtighten.

1

2

9) Remove aerator (H) and ush

lines free of debris. Check for

leaks.

2

Installation

H

1

3

2

B

D

Page is loading ...

Symmons SLC-9612-STN-1.5 Installation guide

Symmons SLC-9612-STN-1.5 Installation guide

in other languages

Related papers

Other documents