DataCard SR200 Installation guide

Datacard

®

SR200 & SR300 Card Printers and

LM200 & LM300 Laminators

Installation Guide

March 2014

Part No. 527407-001, Rev. A

ii

Notice

Pleasedonotattempttooperateorrepairthisequipmentwithoutadequatetraining.

Anyuse,operationorrepairyouperformthatisnotinaccordancewiththeinformation

containedinthisdocumentationisatyourownrisk.

TheseproductsconformtoregulatoryrequirementsasspecifiedinNorthAmerica,

Europe,andAsia.

Referto “ComplianceStatements”onpageiiiformoreinformation.

Trademark Acknowledgments

DatacardisaregisteredtrademarkandservicemarkofDataCardCorporationinthe

UnitedStatesandothercountries.

MasterCardisaregisteredtrademarkofMasterCardInternationalIncorporated.

VisaisaregisteredtrademarkofVisaInternationalServiceAssociation.

AdobeandReaderareregisteredtrademarksofAdobeSystemsIncorporated.

Windowsisaregisteredtrademarkof

MicrosoftCorporation.

Allotherproductnamesarethepropertyoftheirrespectiveowners.

Proprietary Notice

ThedesignandinformationcontainedinthesematerialsareprotectedbyUSand

internationalcopyrightlaws.

AlldrawingsandinformationhereinarethepropertyofDataCardCorporation.All

unauthorizeduseandreproductionisprohibited.

DatacardGroup

11111BrenRoa dWest

Minnetonka,MN55343‐9015

Phone:952‐933‐1223

Fax:952‐933‐7971

www.datacard.com

©2014DataCardCorporation.Allrightsres e r ved .

iii

Compliance Statements

Liability Statement

TheWARNINGandCAUTIONlabelshavebeenplacedontheequipmentforyoursafety.Pleasedo

notattempttooperateorrepairthisequipmentwithoutadequatetraining.Anyuse,operationor

repairincontraventionofthisdocumentisatyourownrisk.

Safety

AllDatacard®productsarebuilttostrictsafetyspecificationsinaccordancewithCSA/UL60950‐1

requirementsandtheLowVo ltageDirective2006/95/EC.

Therefore,safetyissuespertainingtooperationandrepairofDatacard®equipmentareprimarily

environmentalandhumaninterface.

Thefollowingbasicsafetytipsaregiventoensuresafeinstallation,operationand

maintenanceof

Datacard®equipment.

• Connectequipmenttoagroundedpowersource.Donotdefeatorbypassthegroundlead.

• Placetheequipmentonastablesurface(table)andensurefloorsintheworkareaaredryand

non‐slip.

• Knowthelocationofequipmentbranchcircuitinterruptersorcircuitbreakersandhowtoturn

themonandoffincaseofemergency.

• Knowthelocationoffireextinguishersandhowtousethem.ABCtypeextinguishersmaybe

usedonelectricalfires.

• Knowlocalproceduresforfirstaidandemergencyassistanceatthecustomerfacility.

• Useadequatelightingattheequipmentlocation.

• Maintaintherecommendedtemperatureandhumidityrangeintheequipmentarea.

iv

Regulatory Compliance

Notice for USA (FCC notice)

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforClassAcomputing

devices,pursuanttoPart15ofFCCrules.Theselimitsaredesignedtoprovidereasonable

protectionagainstharmfulinterferencewhentheequipmentisoperatedinacommercial

environment.Thisequipmentgenerates,uses,andcanradiate

radiofrequencyenergy.Ifthis

equipmentisnotinstalledandusedinaccordancewiththisinstructionmanual,itmaycause

harmfulinterferencetoradiocommunications.Operationofthisequipmentinaresidentialarea

islikelytocauseharmfulinterferenceinwhichcasetheuserwillberequiredtocorrectthe

interferenceattheirownexpense.Changesormodificationsnotexpresslyapprovedbytheparty

responsibleforcompliancecouldvoidtheuser'sauthoritytooperatetheequipment.

Notice for Canada

ThisDevicecomplieswithIndustryCanadaLicense‐exemptRSSstandard(s).Operationissubject

tothefollowingtwoconditions:1)thisdevicemaynotcauseinterference,and2)thisdevice

mustacceptanyinterference,includinginterferencethatmaycauseundesiredoperationofthe

device.

CetappareilestconformeavecIndustrieCanadaRSS

standardexemptesdelicence(s).Son

fonctionnementestsoumisauxdeuxconditionssuivantes:1)cedispositifnepeutcauserdes

interférences,et2)cetappareildoitacceptertouteinterférence,ycomprislesinterférencesqui

peuventcauserunmauvaisfonctionnementdudispositif.

Notice for Europe

TheEUDeclarationofConformitycanbefoundonDatacard.com

WeherebycertifythatthisprintercomplieswithEMCDirective2004/108/EC,R&TTEDirective

1999/5/EC,andtheEURoHSDirectiveEUDirective2011/65/EC.ThisprinterconformstoClassAof

EN55022andtoEN301489‐5.Operationofthisequipment

inaresidentialenvironmentmay

possiblycauseinterference.Intheeventofinterference,theusers,attheir

ownexpense,willbe

requiredtotakewhatevermea sur esarenecessarytocorrecttheproblem.

Notice for China (Simplified Chinese)

警告

此为 A 级产品，在生活环境中，

该产品可能会造成无线电干扰。

在这种情况下，可能需要用户

对干扰采取切实可行的措施。

v

Notice for Taiwan (Traditional Chinese)

Notice for Japan

JapaneseVoluntaryControlCouncilforInterference(VCCI)classAstatement

Korea Communications Commission (KCC) statement

California Proposition 65 Compliance

WARNING: This product contains chemicals, including lead, known to the State of California to

cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

vi

Revision Log

Datacard

®

SR200 & SR300 Card Printers and

LM200 & LM300 Laminators Installation Guide

Revision Date DescriptionofChanges

AMarch2014 Firstreleaseofthisdocument

vii

Table of Contents

Chapter 1: Planning the Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Related Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Whom to Call for Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Unpacking the Printer and Laminator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Packing Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Unpacking the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Unpacking the Laminator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Choosing a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Ventilation Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Printer Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Supported Operating Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installing More Than One Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

USB Installation Overview (no Smart Card) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

USB Installation Overview (with Smart Card) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Network Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Network Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 2: Installing the Hardware Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installing the Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting the Laminator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installing the Card Hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installing the Card Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Card Stacker on SR200 or SR300 Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Card Stacker on Optional Laminator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Plugging in the Power Cord(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting the Data Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Connecting the USB Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting the Network Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 3: Installing the Smart Card Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Downloading and Installing the Gemalto Contactless Driver . . . . . . . . . . . . . . . . . . . . . . . . . 17

Downloading and Installing the Duali Contactless or Duali Contact/Contactless Driver . . . 19

Installing the Identive Dual Contact/Contactless Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Installing the Identive Driver Automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Downloading and Installing the Identive Driver Manually . . . . . . . . . . . . . . . . . . . . . . . . . 21

Installing the iCLASS/pcProx Driver and Support Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

viii

Installing the iCLASS Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Installing the pcProx Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Chapter 4: Installing the USB Printer Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Installing with a USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Windows 7 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Windows XP Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Windows Vista or Windows 2000 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

After Installing the USB Printer Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Chapter 5: Installing the Status Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Installing the Status Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Setting the Unit Number, Printer Name, and Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Chapter 6: Network Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

About Network Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Choosing How to Assign the Network Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

IP Security Using a Printer Certificate (IPSec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

IP Security Using a Preshared Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Installing the Network Printer Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Sharing a Printer on a Network Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Preparing to Share a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Setting up Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Chapter 7: Removing Printer Driver and Status Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . 81

Removing the Printer Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Removing the Status Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Updating the Printer Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

SR200 & SR300 Card Printers and LM200 & LM200 Laminators Installation Guide 1

Chapter 1: Planning the

Installation

Thischapterprovidesinfo rmationaboutthisUser’sGuide.Italso

containsinformationtohelpplantheinstallationofSR200&SR300card

printersandoptionalLM200&LM300laminators.

About This Manual

ThismanualprovidesdetailedinstructionsforinstallngtheSR200&SR300cardprintersandthe

optionalLM200&LM300cardlaminators.

 Chapter 1:"PlanningtheInstallation”—Providesinformationaboutthismanual,aswellas

backgroundinformationneededtoplanforprinterandlaminatorinstallation.

 Chapter 2:"InstallingtheHardwareComponents”—Providesinstructionsforunpackingand

installingthehardwarecomponents,cables,andpowercordsoftheprinterandlaminator.

 Chapter 3:"InstallingtheSmartCardDriver”—Containsproceduresforinstallingthe

appropriatesmartcarddriver.Thisisnecessaryonlyifthecardprinterisequippedwithan

optionalsmartcardupgrade.

 Chapter 4:"InstallingtheUSBPrinterDriver”—ProvidesinstructionsforinstallingtheUSB

printerdriverontothePC(s)usedtocre a teandprintcards.

 Chapter 5:"InstallingtheStatusMonitor”—ProvidesinstructionsforinstallingtheStatus

MonitorontothePC(s)usedtocreateandprintcards.

 Chapter 6:"NetworkInstallation”—Describeshowtoinstallthenetworkprinterdriver,how

toconfiguretheprinterforuseonalocalnetwork,andhowtoshareanetworkedprinter.

 Chapter 7:"RemovingPrinterDriverandStatusMonitor”—Providesinstructionsfor

uninstallingtheprinterdriverorStatusMonitorfromthePC.Instructionsareincludedfor

updatingtheprinterdriverifanewversionisreleased.

Related Documentation

RefertotheDatacardSR200&SR300CardPrintersandLM200&LM300LaminatorsUser’sGuide

forinformationaboutusingtheprinterandlaminatortocreatecards.

RefertotheDatacardSR200&SR300Plug‐inUser’sGuide forinformationaboutusingthecard

printerwithDatacardIDsoftwareapplications.The

manualincludesinstructionsforcreating

magneticstripeen codingconfigurations.

2 Planning the Installation

Whom to Call for Assistance

Ifyouworkwith aDatacard‐authorizeddealer,distributor,orvalue‐addedreseller,contactthem

forassistance.Avalue‐addedresellerprovidestheSR200&SR300cardprintersandLM200&

LM300laminatorsaspartofanoverallsystem.

Ifanycontentsoftheboxaremissing,contactyourDatacard‐authorized

dealer,distributor,or

reseller.IfyoupurchasedyourprinterdirectlyfromDatacard,contacttheDatacardCustomer

CareCenterinyourregion:

Makesurethatyouhavetheprinterserialnumber,locatedonthebackoftheprinter,and

optionallaminatorserialnumber,whenyoucall.

Unpacking the Printer and Laminator

Unpackthecardprinterandthelaminator(ifpurchased)fromtheirshippingcartons.

Packing Lists

Theshippingcartonforthecardprintercontains:

 SR200orSR300cardprinter

 Powercord

 Cleaningcard

 Cardstack er

 Whitegloves

 Tweezers

 SR200&SR300andLM200&LM300documentationshippingkit:

 ReadMeFirstdocument

 Owner’sLibraryCD‐ROM

 SR200&SR300CardPrintersandLM200&LM300LaminatorsInstallationGuide

 Warranty

 SR200&SR300Support(Plug‐in)CD

Americas +1800.328.3996or952.988.2316

Europe,Middle East,andAfrica +441489555627

AsiaPacific +85228210121

ThismanualdescribestheSR200orSR300printerandtheLM200orLM300laminator.

Theinstructionsapplytobothprintersandbothlaminators,exceptwhenstated.

SR200 & SR300 Card Printers and LM200 & LM200 Laminators Installation Guide 3

Theshippingcartonforthelaminatorcontains:

 LM200orLM300cardlaminator

 Joiningplate

 Cleaningcard

 Powercord

 Take‐upcore

Youmustprovidetheseitemsororderseparately:

 USBcable

 Networkcable(ifprinteristobeusedoveranetwork)

 Inkribbon

 Retransferfilm

 Blankcards

 Cleaningkit

Unpacking the Printer

RemovetheSR200orSR300cardprinterfromtheshippingcarton.Removeallpackingtapefrom

insideandaroundtheprinter.

Unpacking the Laminator

Removethelaminatorfromtheshippingcontainer.Makesuretoremoveallpackingtapeinside

andaroundthelaminator.Removetheprotectivecushionthatprotectsboththeheatedroller

andtheplatenroller.

RefertotheDatacardSR200&SR300CardPrintersandLM200&LM300LaminatorsUser’s

Guideforpartnumbersandorderinginformation.

Caution:Thecardprinterweighsapproximately27.6pounds(12.5kg)withoptions

installed.Usecarewhenremovingtheprinterfromtheshippingcontainer.

Save the shipping carton and packaging materials. They are required if you need to store,

move, or return the printer for service. Replacements are not available.

Caution:Thelaminatorweighsapproximately17pounds(8kg).Usecarewhenremoving

thelaminatorfromtheshippingcontainer.

Save the shipping carton and packaging materials. They are required if you need to store,

move, or return the laminator for service. Replacements are not available.

4 Planning the Installation

Choosing a Location

Theperformanceoftheprinterandoptionallaminatorisstronglyinfluencedbytheinstallation

location.Installtheunit(s)inalocationthatmeetsthefollowingcriteria:

 Installtheprinterinalocationthatmeetsorex ceedsISO14611‐1Class8cleanliness

standards.Usingtheprinterindustylocationsmaycauseprintblurringandprinthead

malfunctions.

 Powerofftheprinterwhenprintingisnotbeingperformed.Leavingpoweronforlong

periodswithoutprintingmayallowfinedusttocollectinsidetheprinter,causingprint

blurringandcausingdusttoadheretocards.

 Avoidlocationssusceptibletostrongvibrationorshock.

 Avoidlocationsexposedtodirectsunlight.

 Avoidlocationswherethereisapossibilityofmetalobjectsorotherforeignmaterial

enteringtheprinter.

 Avoidareasnearwallswithlittleventilation.Referto“VentilationClearance”onpage 5.

 Avoidunstablelocationsandangledsurfaces.

 Avoidlocationspronetostaticelectricity,suchasacarpetedroom.

 Avoidareasnearairconditioners,humidifiers,orheatsourcesthatmaycausecondensation

withintheprinter.

Operating Environment

Installtheprinterinanenvironmentwiththefollowingrecommendedtemperatureandhumidity

range:

 Temperature:59°–86°F(15°–30°C),or63°–83°F(17°–28°C)ifusingpeel‐off(PO)orUVink.

 Humidity:35%–70%,non‐condensing,or35%–60%ifusingpeel‐offorUVink.

Security

BoththeSR200&SR300printersandtheLM200&LM300laminatorshaveslotsforcable‐type

securitylocks.Ifyouplantouseacablelock,selectalocationthatprovidesasecureplaceto

fastenthecables.

Caution:Usingtheprinterinanenvironmentwithtemperaturesthatarecoolerthan

therecommendedrangecancauseretransfererrors.Usingtheprinterinan

environmentwithtemperaturesthatarewarmerthantherecommendedrangecan

causeerrorssuchascardwarpingandwrinklingofthefilm.

SR200 & SR300 Card Printers and LM200 & LM200 Laminators Installation Guide 5

Ventilation Clearance

Ventilationholesareprovidedforthecoolingfansatthebottomandsidesoftheprinter,andat

thebackofthelaminator.Installtheprinterandlaminatorsothatthesidesareatleast8inches

(200mm)awayfromthesurroundingwall.Keepthebackoftheunitsat

least4inches(100mm)

awayfromawall.Donotplaceanyobjectsontopoftheprinterorlaminator.

Printer Options

Printeroptionsinstalledinthefactoryaremarkedontheoptionslabelatthebackoftheprinter.

Eachoptioninstalledhasamarkedorfilledsquare.Forexample,thefollowingillustrationisfora

printerwithduplex(double‐sided),bendremedy,andmagneticencoderoptions.

Theprintercanhaveoneofthesefactory‐installedsmartcardreaderoptions:

 ContactICEnc/R/W

 DualiContactless

 DualiContact/Contactless

 Gemalto®Contactless

 Indentive®DualContact/Contactless

6 Planning the Installation

ThesmartcardoptionissetupforusewithaUSBdatacableonly.Networkinstallationisnot

supportedforsmartcarduse.Ifsmartcardsaretobeencoded,downloadandinstallthesmart

carddriverbeforeconnectingtheprinterorinstallingtheprinterdriver.Referto“Installingthe



SmartCardDriver” onpage 17todownloadandinstallthesmartcarddriver.

Supported Operating Systems

Theprinterandprinterdrivercanbeinstalledonthefollowingoperatingsystems:

 Windows7(testedwithServicePack1installed)

 WindowsVista(testedwithServicePack2installed)

 WindowsXP(testedwithServicePack3installed)

 Windows2000(testedwithServicePack4installed)

Installing More Than One Printer

FollowtheseguidelinestoinstallmorethanoneprinteronaPC:

 Youcaninstallupto10cardprintersononePC.

 YoucaninstallbothSR200&SR300printersonthesamePC.

 Ifyouwantbothanetwork‐connectedprinterandaUSB‐connectedprinterofthesametype

installedonthesamePC,installtheUSB‐connectedprinterfirstforbestresults.

 IfyouplantoinstallmultipleprintersofthesametypeononeormorePCs,assigntheunit

numbersandprinternamesusingtheStatusMonitorandaUSBconnection.EachPCmust

usetheunitnumberandprinternameassignedtoeachprinter.

Installation Requirements

Beforeinstallingtheprinter,makesurethatyouunderstandandfollowtheseimportantpoints:

 Iftheprinterhasasmartcardreaderinstalled,youmustinstallthesmartcarddriversfirst.

Referto“InstallingtheSmartCardDriver”onpage 17.

 Knowtheunitnumberassignedtoeachprinterbeinginstalled.Referto“SettingtheUnit

Number,PrinterName,andConnection”onpage 59.

 IfyouupgradetheoperatingsystemofyourPCtoWindowsVistaorWindows7,removeall

SR200orSR300printerdriversbeforeupgrading.Installtheprinter(s)againaftertheupgrade

iscompleted.

 Contactyourserviceproviderforcurrentlysupportedoperatingsystems.

Caution:Duringinstallation,donotpowerontheprinteruntildirectedtodoso.

SR200 & SR300 Card Printers and LM200 & LM200 Laminators Installation Guide 7

Installation Overview

Thissectionprovidesanov erviewofthestepsyouwillfollowwheninstallingtheprinter.

USB Connection

ThesimplestandmostdirectmethodofconnectingthecardprintertoaPCiswithaUSBcable.

Withthismethod,thecardprinterisalocalprinterandonlytheconnectedPCcanuseittoprint

cards.

Notethattwoormorecardprinterscanbeconnecte dto

aPC,eachwithitsownUSBcable,as

shownbelow:

TheUSBinstallationprocedurevaries,dependingonwhethertheprinterincludesasmartcard

option.UseoneofthefollowingOverviewsectionstohelpyouplanthestepsneededtoinstall

yourprinter.

USB Installation Overview (no Smart Card)

PerformthesestepstoinstallyourcardprinterwithaUSBconnectionwhentheprinterdoesnot

containasmartcardoption.RefertoChapters2,4,and5ofthismanualfordetailedinstructions.

1. (Optional)InstallIDsoftware,suchasDatacard

®

IDWorks

®

identificationsoftware,ont othe

PCthatwillbeusedtodesignandprintcards.

2. Physicallyinstalltheprinterandoptionallaminator:

a. Connectthelaminator(ifused)totheprinter.

b. Installthecardhopper.

c. Installthecardstacker.

Ifyourprinterincludesasmartcardoption,itmustbeconnectedtothePCwithaUSB

cable.NetworkconnectionforsmartcarduseisnotsupportedbytheSR200&SR300

printers.

8 Planning the Installation

d. Connectthepowercordtotheprinterandtothelaminator(ifused).Poweronboth

devicesandthenpoweroffagain.

e. Installprintingandlaminatingsupplies(inkribbon,retransfermaterial,laminatorfilm

cartridges,andcards).

3. UsetheInstallationCDtoinstalltheSR‐CPprinterdriverontothePC.

(Youwillbeinstructed

toconnecttheUSBcableduringthisstep.)

4. UsetheInstallationCDtoinstalltheStatusMonitorontothePC.

5. PowerontheprinterandconfiguretheconnectionbetweenthePCandtheprinter.If

necessary,usethePCtoassigntheDatacardSR‐CRretransferprinter

plug‐intotheprinter.

USB Installation Overview (with Smart Card)

PerformthesestepstoinstallyourcardprinterwithaUSBconnectionwhentheprinterdoes

containasmartcardoption.RefertoChapters2–5ofthismanualfordetailedinstructions.

1. (Optional)InstallIDsoftware,suchasDatacard

®

IDWorks

®

identificationsoftware,ontothe

PCthatwillbeusedtodesignandprintcards.

2. InstalltheappropriatesmartcarddriverontothePC.

3. Physicallyinstalltheprinterandoptionallaminator:

a. Connectthelaminator(ifused)totheprinter.

b. Installthecardhopper.

c. Installthecardstacker.

d. Connectthepowercord

totheprinterandtothelaminator(ifused).Poweronboth

devicesandthenpoweroffagain.

e. Installprintingandlaminatingsupplies(inkribbon,retransfermaterial,laminatorfilm

cartridges,andcards).

4. UsetheInstallationCDtoinstalltheSR‐CPprinterdriverontothePC.(Youwillbeinstructed

to

connecttheUSBcableduringthisstep.)

5. UsetheInstallationCDtoinstalltheStatusMonitorontothePC.

6. PowerontheprinterandconfiguretheconnectionbetweenthePCandtheprinter.If

necessary,usethePCtoassigntheDatacardSR‐CRretransferprinterplug‐intothe

printer.

Caution:DonotconnecttheUSBcabletotheprinterandPCyet.Theprinter

drivermustbeinstalledfirsttoenablecommunicationbetweenthecomponents.

Caution:DonotconnecttheUSBcabletotheprinterandPCyet.Theprinter

drivermustbeinstalledfirsttoenablecommunicationbetweenthecomponents.

SR200 & SR300 Card Printers and LM200 & LM200 Laminators Installation Guide 9

Network Connection

Whenalocalnetworkisavailable,boththecardprinterandthePCcanbeconnectedtothe

network.Whenanetworkconnectionisused,youcanprintcardsfromanyPCconnectedtothat

network.

EachPCmusthavethedesignsoftwareusedtocreateandprintcards,musthave

theSR‐CP

printerdriverandStatusMonitorinstalled,andmustbeconnectedtothesamenetworkasthe

printer(s).

Network Installation Overview

Performthesestepstoinstallyourcardprintertoanetwork.RefertoChapters2,4,5,and6of

thismanualfordetailedinstructions.

1. (Optional)InstallIDsoftware,suchasDatacard

®

IDWorks

®

identificationsoftware,ont othe

PCthatwillbeusedtodesignandprintcards.

2. Physicallyinstalltheprinterandoptionallaminator:

a. Connectthelaminator(ifused)totheprinter.

b. Installthecardhopper.

Remember,useaUSBconnectionifyourcardprintercontainsanoptionalsmartcard

reader.NetworkconnectionforasmartcardisnotsupportedbytheSR200&SR300

printers.

10 Planning the Installation

c. Installthecardstacker.

d. Connectthepowercordtotheprinterandtothelaminator(ifused).Poweronboth

devicesandthenpoweroffagain.

e. Installprintingandlaminatingsupplies(inkribbon,retransfermaterial,laminatorfilm

cartridges,andcards).

3. UsetheInstallationCDtoinstalltheSR‐CPprinter

driverontothePC.(Boththenetworkand

USBcableswillbeconnectedduringthisstep.)

4. UsetheInstallationCDtoinstalltheStatusMonitorontothePC.

5. PowerontheprinterandconfiguretheconnectionbetweenthePCandtheprinter.

Ifnecessary,usethePCtoassigntheDatacard

SR‐CRretransferprinterplug‐intotheprinter,

andtosetuptheunitnumberandprintername.SetthedefaultinterfacevaluetoNetwork.

6. PowerofftheprinteranddisconnecttheUSBcable.Usethenetworkcabletoconnectthe

printertoyourlocalnetwork.

7. Reinstalltheprinter

driverusingthenetworkcable.

8. Assigntheprinter’sIPaddre ss,ifnecessary.

9. SetupIPsecurity,ifneeded,usingeitheraprintercertificateorapresharedkey .

10. Setupprintersharing,ifdesired.

Caution:DonotconnecttheUSBornetworkcabletotheprinterandPCyet.The

printerdrivermustbeinstalledfirsttoenablecommunicationbetweenthe

components.

SR200 & SR300 Card Printers and LM200 & LM200 Laminators Installation Guide 11

Chapter 2: Installing the

Hardware Components

Thischapterprovidesstep‐by‐stepinstructionsforinstallingphysical

components,powercords,andcablesoftheSR200&SR300cardprinters

andoptionalLM200&LM300laminators.

Installing the Components

Usethefollowingprocedurestoconnecttheoptionallaminatortothecardprinter,andtoinstall

thecardhopperandthecardstackertotheprinterorlaminator.

Connecting the Laminator

Usetheprovidedjoiningplatetoconnectthelaminator(ifused)tothecardprinter.

1. Placetheprinteronthework

surfacewiththejoiningplate

attached.

2. Mountthelaminatoroverthe

holesonthejoiningplate.

Theinfraredportsontheprinter

andlaminatormustbealignedfor

thelaminatortowork.

Make sure to install both units on a secure, level surface. Make sure the laminator and the

printer fit securely into the joining plate holes.

Caution:Makesurethatthepowerswitchisturnedoffandthepowercordisdetached

fromthereceptaclebeforeconnectingordisconnectingthelaminator.Otherwise,

electricshock,fire,ormalfunctionoftheproductmightoccur.

JoiningPlate

12 Installing the Hardware Components

Installing the Card Hopper

1. Ifpresent,removestyrofoampackingfoamfrominsidethecardhopper.

2. Insertthecardhopperhooksintothereceptacleslotsontheprinter.

3. Slidethecardhopperdownuntilitclicksintoplace.

Installing the Card Stacker

Ascompletedcardsexittheprinterorlaminator,theyarecollectedinthecardstacker.Installthe

cardstackerbelowthecardoutslotontheleftsideoftheprinterorthelaminator(ifused).

Card Stacker on SR200 or SR300 Printer

Whennolaminatorisused,placethestack ertabsintotheattachmentslotsonthesideofthe

printer.Besuretohangthecardstackerontheattachmentslots,notonthecardoutslot.

The card hopper can hold up to 100, 0.030 inch (0.75 mm) thick cards.

The card stacker can hold up to 100 0.030 inch (0.75mm) thick cards.

CardOutSlot

Page is loading ...

DataCard SR200 Installation guide

This manual is also suitable for

DataCard SR200 Installation guide

Related papers

Other documents