Bosch 7000 User manual

DINION capture 5000/7000

VER Series

en Installation Manual

DINION capture 5000/7000 Table of Contents | en 3

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2012.01

Table of Contents

1Safety 5

1.1 Safety precautions 5

1.2 Important safety instructions 6

1.3 Important notices 9

1.4 FCC & ICES compliance 13

1.5 Bosch notices 15

2 Description 16

2.1 Parts List 16

3 Installing the DINION capture 17

3.1 Determining the Range 17

3.2 Determining the Angle 18

3.3 Mounting the DINION capture 20

3.4 Preparing the Wiring 23

3.4.1 Power Input Connections 23

3.4.2 Video Connections 23

3.5 Making the Connections 24

3.6 Automatic Mode Switching 24

4 Configuration 28

4.1 Menus 28

4.1.1 Top level menus 28

4.1.2 Accessing Menu Keys 28

4.1.3 Menu Navigation Keys 31

4.2 Pre-Defined Modes 31

4.3 Day/Night switching (DINION capture 7000) 32

4.4 Camera control communication (Bilinx) 33

4.5 Main menu structure 34

4.5.1 Mode submenu 35

4.5.2 ALC submenu 35

4.5.3 Shutter/AGC submenu 37

4.5.4 Day/Night submenu

(Overview Camera - DINION capture 7000 only) 39

4.5.5 Enhance / Dynamic Engine submenu 41

4 en | Table of Contents DINION capture 5000/7000

| 1.0 | 2012.01 Installation Manual Bosch Security Systems, Inc.

4.5.6 Color submenu

(Overview Camera - DINION capture 7000 only) 43

4.5.7 VMD submenu 44

4.6 Install menu structure 45

4.6.1 Language submenu 46

4.6.2 Lens Wizard submenu 46

4.6.3 Alarm I/O submenu 47

4.6.4 Connections submenu 48

4.6.5 Test signal submenu 49

4.6.6 Camera ID submenu 50

4.6.7 Privacy masking submenu 51

4.6.8 Defaults submenu 51

A Dimensional Drawings 52

DINION capture 5000/7000 Safety | en 5

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2012.01

1Safety

1.1 Safety precautions

DANGER!

High risk: This symbol indicates an imminently hazardous

situation such as "Dangerous Voltage" inside the product.

If not avoided, this will result in an electrical shock, serious

bodily injury, or death.

WARNING!

Medium risk: Indicates a potentially hazardous situation.

If not avoided, this could result in minor or moderate bodily

injury.

CAUTION!

Low risk: Indicates a potentially hazardous situation.

If not avoided, this could result in property damage or risk of

damage to the unit.

NOTICE!

This symbol indicates information or a company policy that

relates directly or indirectly to the safety of personnel or

protection of property.

6 en | Safety DINION capture 5000/7000

| 1.0 | 2012.01 Installation Manual Bosch Security Systems, Inc.

1.2 Important safety instructions

Read, follow, and retain for future reference all of the following

safety instructions. Heed all warnings on the unit and in the

operating instructions before operating the unit.

1. Cleaning - Unplug the unit from the outlet before cleaning.

Follow any instructions provided with the unit. Generally,

using a dry cloth for cleaning is sufficient but a moist, fluff-

free cloth or leather shammy may also be used. Do not use

aerosol cleaners.

2. Heat Sources - Do not install the unit near any heat

sources such as radiators, heaters, stoves, or other

equipment (including amplifiers) that produce heat.

3. Object and liquid entry - Never push objects of any kind

into this unit through openings as they may touch

dangerous voltage points or short-out parts that could

result in a fire or electrical shock. Never spill liquid of any

kind in the unit.

4. Lightning - For added protection during a lightning storm,

or when leaving this unit unattended and unused for long

periods, unplug the power source and disconnect the

cable system. This will prevent damage to the unit from

lightning and power line surges.

5. Controls adjustment - Adjust only those controls specified

in the operating instructions. Improper adjustment of

other controls may cause damage to the unit. Use of

controls or adjustments, or performance of procedures

other than those specified, may result in hazardous

radiation exposure.

6. Overloading - Do not overload circuits. This can cause fire

or electrical shock.

7. Power cable protection - Protect the power cable from

foot traffic, from being pinched by items placed upon it,

and at cable's exit from the unit.

DINION capture 5000/7000 Safety | en 7

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2012.01

8. Power disconnect - Units have power supplied to the unit

whenever the power cord is inserted into the power

source. The power cord plug is the main power disconnect

device for switching off the voltage for all units.

9. Power sources - Operate the unit only from the type of

power source indicated on the label. Before proceeding,

be sure to disconnect the power from the cable to be

installed into the unit.

– For external power supplied units, use only the

recommended or approved power supplies.

– For limited power source units, this power source

must comply with EN60950. Substitutions may

damage the unit or cause fire or shock.

– For 24 VAC units, voltage applied to the unit's power

input should not exceed ±10%, or 26.4 VAC. User-

supplied wiring must comply with local electrical

codes (Class 2 power levels). Do not ground the

supply at the terminals or at the unit's power supply

terminals.

– If unsure of the type of power supply to use, contact

your dealer or local power company.

10. Servicing - Do not attempt to service this unit yourself.

11. Damage requiring service - Unplug the unit from the main

AC power source and refer servicing to qualified service

personnel when any damage to the equipment has

occurred, such as:

– the power supply cord or plug is damaged;

– internal exposure to moisture, water, and/or

inclement weather (rain, snow, etc.);

– liquid has been spilled in the equipment;

– an object has fallen into the unit;

– unit has been dropped;

– unit exhibits a distinct change in performance;

– unit does not operate normally when the user

correctly follows the operating instructions.

8 en | Safety DINION capture 5000/7000

| 1.0 | 2012.01 Installation Manual Bosch Security Systems, Inc.

12. Replacement parts - Be sure the service technician uses

replacement parts specified by the manufacturer, or that

have the same characteristics as the original parts.

Unauthorized substitutions may cause fire, electrical

shock, or other hazards.

13. Safety check - Safety checks should be performed upon

completion of service or repairs to the unit to ensure

proper operating condition.

14. Installation - Install in accordance with the manufacturer's

instructions and in accordance with applicable local codes.

15. Attachments, changes or modifications - Only use

attachments/accessories specified by the manufacturer.

Any change or modification of the equipment, not

expressly approved by Bosch, could void the warranty or,

in the case of an authorization agreement, authority to

operate the equipment.

DINION capture 5000/7000 Safety | en 9

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2012.01

1.3 Important notices

All-pole power switch - Incorporate an all-pole power switch,

with a contact separation of at least 3 mm in each pole, into the

electrical installation of the building. If it is needed to open the

housing for servicing and/or other activities, use this all-pole

switch as the main disconnect device for switching off the

voltage to the unit.

Camera signal - Protect the cable with a primary protector if

the camera signal is beyond 140 feet, in accordance with

NEC800 (CEC Section 60).

This product has been tested according to standard CIE/IEC

62471:2006 “Photobiological safety of lamps and lamp

systems” and found to meet Risk Group 1 for exposure limit

4.3.7 “Infrared radiation hazard exposure limits for the eye.”

For other hazard exposure limits, the product was found to be

exempt. Risk Group 1 is characterized in the standard as

“products are safe for most use applications, except for very

prolonged exposures where direct ocular exposures may be

expected.” Risk Group 1 sources do not pose an infrared

radiation hazard for the eye for times less than 100 s at

distances beyond 200 mm or 8 inches.

Accessories - Do not place this unit on an unstable stand,

tripod, bracket, or mount. The unit may fall and cause serious

injury and/or serious damage to the unit. Use only with the

cart, stand, tripod, bracket, or table specified by the

manufacturer. When a cart is used, use caution and care when

moving the cart/apparatus combination to avoid injury from

tip-over. Quick stops, excessive force, or uneven surfaces may

cause the cart/unit combination to overturn. Mount the unit

per the manufacturer's instructions.

NOTICE!

RISK GROUP 1

IR emitted from this product.

10 en | Safety DINION capture 5000/7000

| 1.0 | 2012.01 Installation Manual Bosch Security Systems, Inc.

The Exposure Hazard Value for the product (ratio of the

Exposure level to the Exposure limit) is up to 1.8 at a test

distance of 200 mm or 8 inches. The Hazard Distance (distance

beyond which the product falls into the exempt/safe group) is

at most 350 mm or 14 inches. Note that typical operating

distances for license plate capture (3.8 m or 12.5 feet and

greater) are much greater than the Hazard Distance.

When servicing the unit, physically disconnect the power supply

to avoid possible IR exposure to the eyes. If physical

disconnection is not possible, use appropriate shielding to

block the LED panel or use eye protection with a transmission

of 50% or less at a wavelength of 850 nm.

Coax grounding:

– Ground the cable system if connecting an outside cable

system to the unit.

– Follow proper safety precautions such as grounding for

any outdoor device connected to this unit.

U.S.A. models only - Section 810 of the National Electrical Code,

ANSI/NFPA No.70, provides information regarding proper

grounding of the mount and supporting structure, grounding of

the coax to a discharge unit, size of grounding conductors,

location of discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

Electronic Surveillance - This device is intended for use in

public areas only. U.S. federal law strictly prohibits

surreptitious recording of oral communications.

Disposal - Your Bosch product was developed and

manufactured with high-quality material and components that

can be recycled and reused. This symbol means that electronic

and electrical appliances, which have reached the end of their

working life, must be collected and disposed of separately

from household waste material. Separate collecting systems

are usually in place for disused electronic and electrical

products. Please dispose of these units at an environmentally

compatible recycling facility, per European Directive 2002/96/

EC

DINION capture 5000/7000 Safety | en 11

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2012.01

Environmental statement - Bosch has a strong commitment

towards the environment. This unit has been designed to

respect the environment as much as possible.

Electrostatic-sensitive device - Use proper CMOS/MOS-FET

handling precautions to avoid electrostatic discharge.

NOTE: Wear required grounded wrist straps and observe proper

ESD safety precautions when handling the electrostatic-

sensitive printed circuit boards.

Fuse rating - For protection of the device, the branch circuit

protection must be secured with a maximum fuse rating of 16A.

This must be in accordance with NEC800 (CEC Section 60).

Moving - Disconnect the power before moving the unit. Move

the unit with care. Excessive force or shock may damage the

unit.

Outdoor signals - The installation for outdoor signals, especially

regarding clearance from power and lightning conductors and

transient protection, must be in accordance with NEC725 and

NEC800 (CEC Rule 16-224 and CEC Section 60).

Permanently connected equipment - Incorporate a readily

accessible disconnect device external to the equipment.

Pluggable equipment - Install the socket outlet near the

equipment so it is easily accessible.

Power lines: An outdoor system should not be located in the

vicinity of overhead power lines, electrical lights, or power

circuits, or where it may contact such power lines or circuits.

When installing an outdoor system, extreme care should be

taken to keep from touching power lines or circuits, as this

contact may be fatal.

U.S.A. models only - refer to the National Electrical Code Article

820 regarding installation of CATV systems.

12 en | Safety DINION capture 5000/7000

| 1.0 | 2012.01 Installation Manual Bosch Security Systems, Inc.

11-30 VDC / 24 VAC power source: This device is intended to

operate with a limited power source; this power source must

comply with EN60950. The device is designed to operate at

either 11-30 VDC or 24 VAC (if PoE is not available). User

supplied wiring must be in compliance with electrical codes

(Class 2 power levels). If 24 VAC is used, do not ground the

24 VAC supply at the terminals or at the device's power supply

terminals.

Connections: The unit has connection terminals on flying leads.

In wet or outdoor installations use a field wiring box with NEMA

3 or IP55 protection level or better. Make the connections

inside the water tight compartment. After connections are

made ensure that the watertight compartment is tightly closed

and cables and conduits are properly sealed to prevent ingress

of water.

SELV - All the input/output ports are Safety Extra Low Voltage

(SELV) circuits. SELV circuits should only be connected to

other SELV circuits.

Because ISDN circuits are treated like telephone-network

voltage, avoid connecting the SELV circuit to the Telephone

Network Voltage (TNV) circuits.

DINION capture 5000/7000 Safety | en 13

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2012.01

1.4 FCC & ICES compliance

FCC & ICES Information

(U.S.A. and Canadian Models Only)

This device complies with part 15 of the FCC Rules. Operation is

subject to the following conditions:

– this device may not cause harmful interference, and

– this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules and ICES-003 of Industry Canada. These limits

are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and radiates

radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful

interference, in which case the user will be required to correct

the interference at his expense.

Intentional or unintentional modifications, not expressly

approved by the party responsible for compliance, shall not be

made. Any such modifications could void the user's authority to

operate the equipment. If necessary, the user should consult

the dealer or an experienced radio/television technician for

corrective action.

The user may find the following booklet, prepared by the

Federal Communications Commission, helpful: How to Identify

and Resolve Radio-TV Interference Problems. This booklet is

available from the U.S. Government Printing Office,

Washington, DC 20402, Stock No. 004-000-00345-4.

Informations FCC et ICES

(modèles utilisés aux États-Unis et au Canada uniquement)

Ce produit est conforme aux normes FCC partie 15. la mise en

service est soumises aux deux conditions suivantes :

14 en | Safety DINION capture 5000/7000

| 1.0 | 2012.01 Installation Manual Bosch Security Systems, Inc.

– cet appareil ne peut pas provoquer d'interférence nuisible

et

– cet appareil doit pouvoir tolérer toutes les interférences

auxquelles il est soumit, y compris les interférences qui

pourraient influer sur son bon fonctionnement.

AVERTISSEMENT: Suite à différents tests, cet appareil s’est

révélé conforme aux exigences imposées aux appareils

numériques de Classe A en vertu de la section 15 du règlement

de la Commission fédérale des communications des États-Unis

(FCC). Ces contraintes sont destinées à fournir une protection

raisonnable contre les interférences nuisibles quand l'appareil

est utilisé dans une installation commerciale. Cette appareil

génère, utilise et émet de l'energie de fréquence radio, et peut,

en cas d'installation ou d'utilisation non conforme aux

instructions, générer des interférences nuisibles aux

communications radio. L’utilisation de ce produit dans une

zone résidentielle peut provoquer des interférences nuisibles.

Le cas échéant, l’utilisateur devra remédier à ces interférences

à ses propres frais.

Au besoin, l’utilisateur consultera son revendeur ou un

technicien qualifié en radio/télévision, qui procédera à une

opération corrective. La brochure suivante, publiée par la

Commission fédérale des communications (FCC), peut s’avérer

utile : How to Identify and Resolve Radio-TV Interference Problems

(Comment identifier et résoudre les problèmes d’interférences

de radio et de télévision). Cette brochure est disponible auprès

du U.S. Government Printing Office, Washington, DC 20402,

États-Unis, sous la référence n° 004-000-00345-4.

NOTICE!

This is a class A product. In a domestic environment this

product may cause radio interference, in which case the user

may be required to take adequate measures.

DINION capture 5000/7000 Safety | en 15

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2012.01

1.5 Bosch notices

Video loss

Video loss is inherent to digital video recording; therefore,

Bosch Security Systems cannot be held liable for any damage

that results from missing video information. To minimize the

risk of lost digital information, Bosch Security Systems

recommends multiple, redundant recording systems, and a

procedure to back up all analog and digital information.

Copyright

This manual is the intellectual property of Bosch Security

Trademarks

All hardware and software product names used in this

document are likely to be registered trademarks and must be

treated accordingly.

Note:

This manual has been compiled with great care and the

information it contains has been thoroughly verified. The text

was complete and correct at the time of printing. The ongoing

development of the products may mean that the content of the

user guide can change without notice. Bosch Security Systems

accepts no liability for damage resulting directly or indirectly

from faults, incompleteness, or discrepancies between the user

guide and the product described.

More information

For more information please contact the nearest Bosch Security

Systems location or visit www.boschsecurity.com

16 en | Description DINION capture 5000/7000

| 1.0 | 2012.01 Installation Manual Bosch Security Systems, Inc.

2 Description

The DINION capture is a specialty camera designed to capture

consistent, high-quality images of vehicle license plates.

Available in IP and analog versions, it is ideal for monitoring

parking lots, public areas, and for controlling vehicle access.

The DINION capture overcomes the problems encountered

when using conventional surveillance cameras in vehicle

identification and automatic license plate recognition

applications. The Night Capture Imaging System delivers a

burst of infrared illumination and simultaneously filters out

visible light to ensure clear license plate images in complete

darkness while eliminating the negative effects of headlight

glare.

Advanced Ambient Compensation minimizes plate

overexposure from sunlight for more accurate automatic license

plate recognition. Finally, adjustable imaging modes allow for

fine-tuning the imager for specific regions or license plate

recognition algorithms.

2.1 Parts List

Quantity Description

1 DINION capture 5000, or

DINION capture 7000

1 3 mm Hex Key

1 5 mm Hex Key

1 Mounting Template

1 Printed Manual

DINION capture 5000/7000 Installing the DINION capture | en 17

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2012.01

3 Installing the DINION capture

This section provides instructions for mounting and wiring the

DINION capture.

3.1 Determining the Range

The DINION capture has a recommended operation range with

specified optimal capture distance for each model as shown

below. Installation should aim to control the traffic through one

lane.

Ranges based on capturing:

520 x 115 mm (approximate) license plates on PAL units

(xER-L2Ry-1)

12 x 6 in. (approximate) license plates on NTSC units

(xER-L2Ry-2)

Field of View at Optimal Capture Distance:

License Plate Camera:

2.8 x 2.1 m (PAL units)

6 ft 6 in. x 4 ft 11 in. (NTSC units)

Overview Camera (DINION capture 7000):

Approximately twice the distance of the License Plate Camera.

CAUTION!

The selected mounting location should not place the camera in

a situation where its environmental specifications could be

exceeded.

Ensure the selected location is protected from falling objects,

accidental contact with moving objects, and unintentional

interference from personnel. Follow all applicable building

codes.

18 en | Installing the DINION capture DINION capture 5000/7000

| 1.0 | 2012.01 Installation Manual Bosch Security Systems, Inc.

Table 3.1 Ranges for DINION capture 5000 and 7000 Analog Imagers

3.2 Determining the Angle

The maximum mounting angle of the license plate camera to the

car is 40° for speeds up to 160 km/h (100 mph), both

horizontally and vertically. This angle limits the amount of skew

of the letters on the number plate. If the letters are skewed too

much they will start to become unrecognizable and will reduce

automatic software recognition rates.

For maximum performance ensure the mounting angle is as

narrow as possible. To capture vehicle speeds up to 225 km/h

(140 mph) the horizontal and vertical mounting angle should be

less than 30°.

Model Capture

Range

Optimal

Distance

HFOV VFOV

VER-x2R1-1 3.8–6.4 m

(12.5–21.0 ft)

4.9 m

(16.0 ft)

31.9° 24.2°

VER-x2R1-2 23.0° 17.3°

VER-x2R2-1 5.5–9.1 m

(18–30 ft)

7.1 m

(23.1 ft)

22.3° 16.8°

VER-x2R2-2 16.0° 12.0°

VER-x2R3-1 7.9–13.7 m

(26–45 ft)

10.2 m

(33.5 ft)

15.6° 11.8°

VER-x2R3-2 11.1° 8.3°

VER-x2R4-1 11.3–19.5 m

(37–64 ft)

14.8 m

(48.4 ft)

10.8° 8.1°

VER-x2R4-2 7.7° 5.8°

VER-x2R5-1 16.5–28.0 m

(54–92 ft)

21.3 m

(70.0 ft)

7.5° 5.6°

VER-x2R5-2 5.3° 4.0°

Note: x = L (DINION capture 5000) or D (DINION capture

7000)

DINION capture 5000/7000 Installing the DINION capture | en 19

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2012.01

Figure 3.1 Recommended Vertical and Horizontal Mounting Angle

If the maximum range is exceeded, then the letters become

smaller and more difficult to read. At the maximum range and

angle the width of the number plate covers approximately 12%

of the width of the screen.

1 DINION capture

2 Capture Range

3 Vertical Mounting Angle

4 Horizontal Mounting Angle

NOTICE!

The Capture Range is the distance from the license plate

camera to the license plate. Working below the optimal capture

distance allows a larger area for number plates and more

accurate recognition but less lane area can be covered. If the

imager is too close to the license plate, the plate could

disappear from the field of view before it is captured.

20 en | Installing the DINION capture DINION capture 5000/7000

| 1.0 | 2012.01 Installation Manual Bosch Security Systems, Inc.

3.3 Mounting the DINION capture

For a secure mounting installation, bolts should extend through

the mounting surface and be secured with nuts, washers, and

lock washers on the opposite side. If studs are used, they

should be anchored in concrete or welded to a steel backer

plate.

Refer to the MBE Mounts and Adapters Installation Guide for

more details about attaching the bracket to an MBE-15 Pole

Mount Adapter or to the MBE-17 Wall Mount Adapter.

1. Use the wall mount template supplied in the packaging box

to locate the four mounting holes for the camera bracket.

2. Drill four (4) holes for the mounting bolts. If installing

outdoors, apply a weatherproof sealant around each hole

at the mounting surface.

3. Route the cable. If routing the cable through the wall, drill

a 25.4 mm (1 in.) hole following the wall mount template

and use a weatherproof sealant to seal around the cable to

ensure a weather tight seal between indoors and outdoors,

otherwise route the cable through one of the side holes in

the mounting bracket by removing the plug and routing the

cable through.

(Routing cables through a side hole in the bracket and into

a near junction box makes setup and troubleshooting

simpler.)

CAUTION!

Installation should only be performed by a qualified service

professional in accordance with the National Electrical Code or

applicable local codes.

WARNING!

A stud/bolt diameter of 6.0 mm (or 1/4 inch) able to withstand

a 300 kg (660 lb) pull-out force is recommended. The mounting

material must be able to withstand this pull out force.

Page is loading ...

Bosch 7000 User manual

This manual is also suitable for

Bosch 7000 User manual

Related papers

Other documents