Altronix HUBWAYEX1 Installation guide

Altronix
Brand
Altronix
Model
HUBWAYEX1
Category
Security camera accessories
Type
Installation guide
Agency Listings:
• UL Listed for Commercial CCTV Equipment
(UL 2044).
CUL Listed - CSA Standard C22.2 No.1-04,
Audio, Video and Similar Equipment.
Input:
• 16VAC-24VAC or 12VDC-24VDC, 1W.
These products shall only be powered by a
UL Listed Class 2 power Supply or
Class 2 transformer.
Data:
• RS422/RS485 data inputs.
Video:
• One (1) channel of video over twisted pair
up to a distance of 5000 ft. per channel.
• Active balun/combiners not required.
• One (1) 75 Ohm video output.
Visual Indicators:
• Video signal LED indicator.
Features:
• Picture and Gain control.
• Automatic correction for reverse video polarity.
• One (1) video signal LED.
Mechanical:
• Dimensions (W x L x H approx.):
2.5” x 3.8” x 1” (63.5mm x 96.5mm x 25.4mm).
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or
moisture. This installation should be made by qualified service personnel and should con-
form to all local codes.
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local
codes and authorities having jurisdiction.
Wiring should be UL Listed and/or Recognized wire suitable for the application.
1. Mount HubWayEX1 in desired location utilizing the mounting hole (Fig. 1, pg. 2). Use a proper fastener
and/or wall anchor when securing HubWayEX1 with screw through its mounting hole to the wall.
2. Connect UL Listed Class 2 power Supply or Class 2 transformer to terminals marked [AC/DC Input]
(Fig. 1, pg. 2). Use 22AWG - 16AWG wire for this connection.
3. Connect the BNC video output for HubWayEX1 to the corresponding video input on the head end
equipment (DVR) (Fig. 4, pg. 3).
4. Connect the RS422/RS485 output of the head end equipment (DVR) to the data input terminals marked
[+ DATA –] of the HubWayEX1 unit (polarity must be observed) (Fig. 1, pg. 2).
When using a fixed camera disregard this step.
5. Connect HubWayAv Video Balun/Combiner (Figs. 2a-2b, pg. 2) (or any Video Balun/Combiner or camera
with built-in Video Balun (Fig. 5, pg. 3) with similar PIN configuration (Fig. 3, pg. 2)) at the camera to the
HubWayEX1 unit utilizing CAT-5 or higher structured cable.
Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel] of the
HubWayEX1 (Fig. 1, pg. 2). Plug the RJ45 connector at the opposite end of the structured cable into the
RJ45 jack of the Video Balun/Combiner located at the camera.
6. Connect an external power source to the power inputs of the camera (Fig. 4, pg. 3). Polarity must be observed.
7. Connect the terminals marked [+ DATA –] of the HubWayAv Video Balun/Combiner to the data
terminals of the camera for PTZ control (Figs. 2a-2b, pg. 2). Polarity must be observed.
When using a fixed camera disregard this step.
8. Connect the BNC connector of the HubWayAv Video Balun/Combiner to the BNC video outputs of the
camera (Figs. 2a-2b, pg. 2).
9. The video signal indicator LED (Red) of the HubWayEX1 will illuminate when video signal is present
(Fig. 1, pg. 2). If the LED is not illuminated, no video signal is present.
Overview:
Altronix HubWayEX1 Active UTP Transceiver Module employs automatic gain control (AGC) to transmit
UTP video and RS422/RS485 data over a single CAT-5 or higher structured cable. Unit provides a single cam-
era channel in a compact insulated housing. Video transmission range is up to one (1) mile max.
Specifications:
Rev. 011810
Installation Guide
HubWayEX1
Single Channel Active UTP Transceiver Module
- 2 - HubWayEX1
VIDEO BALUN/COMBINER
CAT5 + D ATA-- POWER
AC
VIDEO
HubWayAv
Data to
Camera
--
+
Wire
Connectors
RJ45 Jack
To BNC
Connector
of Camera
Structured
Cable from
HubWayEX1
1 - White/Orange [VIDEO +]
2 - Orange [VIDEO -- ]
3 - White/Green [DATA +]
4 - Blue [N/A]
5 - White/Blue [N/A]
6 - Green [DATA -- ]
7 - White/Brown [N/A]
8 - Brown [N/A]
Fig. 1
Fig. 2
Fig. 2a Fig. 2b
Fig. 3 - CAT-5 Structured Cable Wiring Color Codes and PIN Configurations
Video output
to head end
equipment
(DVR).
Spring terminal block
for RS422/RS485 input
from head end equipment
(DVR) for PTZ control.
CAT-5 or higher structured
cable to Video/Balun Combiner
at camera.
UL Listed
Class 2
power supply
or Class 2
transformer
HubWayEX1 - 3 -
Typical Applications:
Fig. 4
Fig. 5
Video
Data
Power
Localized
or Centralized
AC or DC
Power Source
Data
Video
Head End Equipment (DVR)
RS485
HubWayAv
Max. video 5000 ft.
AC or DC
PTZ
Camera
Monitor
Power
Power
Localized
or Centralized
AC or DC
Power Source
Data
Video
Head End Equipment (DVR)
RS485
Max. video 5000 ft.
Camera
connections
AC or DC
PTZ Camera
Monitor
DataVideo
- 4 - HubWayEX1
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty | Made in U.S.A.
IIHubWayEX1 B19R
MEMBER
Notes:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Altronix HUBWAYEX1 Installation guide

Altronix
Brand
Altronix
Model
HUBWAYEX1
Category
Security camera accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents