Belden Hirschman RSPS20 User manual

Installation RSPS20/25

Release

09

12/2019

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial Ethernet Rail Switch Power Smart

RSPS20/25

2019-12-06

Installation RSPS20/25

Release

09

12/2019

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation RSPS20/25

Release

09

12/2019

3

Contents

Safety instructions 5

About this manual 11

Key 12

1 Description 13

1.1 General description 13

1.2 Device name and product code 14

1.3 Device views 17

1.3.1 Front view 17

1.3.2 Rear view 19

1.4 Power supply 20

1.4.1 Supply voltage with the characteristic value M9 or K9 20

1.4.2 Supply voltage with the characteristic value CC 20

1.5 Ethernet ports 20

1.5.1 100/1000 Mbit/s twisted pair port (optional) 20

1.5.2 100 Mbit/s F/O port (optional) 21

1.6 Display elements 21

1.6.1 Device state 21

1.6.2 Port status 22

1.7 Management interfaces 23

1.7.1 V.24 interface (external management) 23

1.7.2 SD card interface 23

1.8 Signal contact 24

2 Installation 25

2.1 Checking the package contents 25

2.2 Installing the SD card (optional) 25

2.3 Installing and grounding the device 26

2.3.1 Installing the device onto the DIN rail 26

2.3.2 Grounding the device 27

2.4 Installing an SFP transceiver (optional) 28

2.5 Connecting the terminal blocks 28

4

Installation RSPS20/25

Release

09

12/2019

2.5.1 Supply voltage with the characteristic value M9 or K9 29

2.5.2 Supply voltage with the characteristic value CC 30

2.5.3 Signal contact 31

2.6 Operating the device 32

2.7 Connecting data cables 32

2.8 Filling out the inscription label 32

3 Making basic settings 33

4 Upgrading Software 34

5 Monitoring the ambient air temperature 35

6 Maintenance and service 36

7Disassembly 37

7.1 Removing the device 37

7.2 Removing an SFP transceiver (optional) 38

8 Technical data 39

8.1 General technical data 39

8.2 Dimension drawings 42

8.3 EMC and immunity 43

8.4 Network range 47

8.5 Power consumption/power output 48

8.6 Scope of delivery, order numbers and accessories 48

9 Underlying technical standards 50

A Further support 51

Installation RSPS20/25

Release

09

12/2019

5

Safety instructions

 General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

 Before connecting any cable, read this document, and the safety

instructions and warnings.

 Operate the device with undamaged components exclusively.

 The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

 Certified usage

 Use the product only for the application cases described in the

Hirschmann product information, including this manual.

 Operate the product only according to the technical specifications.

See “Technical data” on page 39.

 Connect to the product only components suitable for the requirements

of the specific application case.

 Installation site requirements

 Install the device in a fire enclosure according to EN 60950-1.

 Exclusively for device variants featuring supply voltage with

characteristic value K9 or M9:

See “Device name and product code” on page 14.

Install this device solely in a switch cabinet or in an operating site with

restricted access, to which maintenance staff have exclusive access.

 Install the device at ambient temperatures > +113 °F (+45 °C) in

“restricted access locations” based on EN 60950-1 exclusively.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6

Installation RSPS20/25

Release

09

12/2019

 Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

 Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

 Keep the ventilation slits free to ensure good air circulation.

 Mount the device in the vertical position.

 At ambient air temperatures > +140 °F (+60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

 Qualification requirements for personnel

 Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

 Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

 Qualified personnel are aware of the dangers that exist in their work.

 Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

 Qualified personnel receive training on a regular basis.

 National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

 Grounding the device

Grounding the device is by means of a separate ground connection on the

device.

 Ground the device before connecting any other cables.

 Disconnect the grounding only after disconnecting all other cables.

 Shielding ground

The overall shield of a connected shielded twisted pair cable is connected

to the grounding connector on the front panel as a conductor.

 Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

 Requirements for connecting electrical wires

 Before connecting the electrical wires, always verify that the

requirements listed are complied with.

Installation RSPS20/25

Release

09

12/2019

7



Requirements for connecting the signal contact

 Requirements for connecting the supply voltage

All of the following requirements are complied with:

 The electrical wires are voltage-free.

 The cables used are permitted for the temperature range of the application case.

Table 1: Requirements for connecting electrical wires

All of the following requirements are complied with:

 The voltage connected complies with the requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

 The connected voltage is limited by a current limitation device or a fuse.

Observe the electrical threshold values for the signal contact.

See “General technical data” on page 39.

Table 2: Requirements for connecting the signal contact

Device variant Requirements

All variants All of the following requirements are complied with:

 The supply voltage corresponds to the voltage specified on the type

plate of the device.

 The power supply conforms to overvoltage category I or II.

 The power supply has an easily accessible disconnecting device (for

example a switch or a plug). This disconnecting device is clearly

identified. So in the case of an emergency, it is clear which

disconnecting device belongs to which power supply cable.

 The cross-section of the ground conductor is the same size as or

bigger than the cross-section of the power supply cables.

 Relevant for North America:

The power supply cables are suitable for ambient air temperatures of

at least 167 °F (75 °C). The power supply cable wires are made of

copper.

Table 3: Requirements for connecting the supply voltage

8

Installation RSPS20/25

Release

09

12/2019

 Supply voltage

The supply voltage is connected to the device casing through protective

elements exclusively.

 For supply voltage connections with protective conductor connection:

First connect the protective conductor before connecting the wires for

the supply voltage.

Only for device

variants featuring

supply voltage with

the characteristic

value CC:

If you connect 2 independent power sources, verify that the minus

terminal is grounded. Failure to follow this instruction can result in

equipment damage.

The wire diameter of the power supply cable is at least 1 mm² (North

America: AWG16) on the supply voltage input.

The following requirements are alternatively complied with:

Alternative 1 The power supply complies with the requirements

for a limited power source (LPS) as per EN 60950-1.

Alternative 2 Relevant for North America:

The power supply complies with the requirements

according to NEC Class 2.

Alternative 3 All of the following requirements are complied with:

 The power supply complies with the

requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

 A fuse suitable for DC voltage is located in the

plus conductor of the power supply.

The minus conductor is on ground potential.

Otherwise, a fuse is also located in the minus

conductor.

Regarding the properties of this fuse:

See “General technical data” on page 39.

Exclusively for

device variants

featuring supply

voltage with

characteristic

value K9 or M9:

All of the following requirements are complied with:

 Supply with DC voltage:

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

The minus conductor is on ground potential. Otherwise, a fuse is also

located in the minus conductor.

Regarding the properties of this fuse:

See “General technical data” on page 39.

The wire diameter of the power supply cable is at least 1 mm² (North

America: AWG16) on the supply voltage input.

 Supply with AC voltage:

A fuse is located in the outer conductor of the power supply.

The neutral conductor is on ground potential at both voltage inputs.

Otherwise, a fuse is also located in the neutral conductor.

Regarding the properties of this fuse:

See “General technical data” on page 39.

The wire diameter of the power supply cable is at least 0.75 mm²

(North America: AWG18) on the supply voltage input.

Device variant Requirements

Table 3: Requirements for connecting the supply voltage

Installation RSPS20/25

Release

09

12/2019

9

 CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

www.hirschmann.com

The product can be used in the industrial sector.

 Interference immunity: EN 61000-6-2

 Emitted interference: EN 55032

 Reliability: EN 60950-1

You find more information on technical standards here:

“Technical data” on page 39

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

 LED or laser components

LED or LASER components according to IEC 60825-1 (2014):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

Device variant Directive

All variants 2014/30/EU (EMC)

Directive of the European Parliament and of the Council on the

harmonisation of the laws of the Member States relating to

electromagnetic compatibility.

2011/65/EU and 2015/863/EU (RoHS)

Directive of the European Parliament and of the Council on the

restriction of the use of certain hazardous substances in

electrical and electronic equipment.

Exclusively for device variants

featuring supply voltage with

characteristic value K9 or M9:

2014/35/EU

Directive of the European Parliament and of the Council on the

harmonisation of the laws of the Member States relating to the

making available on the market of electrical equipment

designed for use within certain voltage limits.

10

Installation RSPS20/25

Release

09

12/2019

 FCC note

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

RSPS20/25

U.S. Contact Information

Belden – St. Louis

1 N. Brentwood Blvd. 15th Floor

St. Louis, Missouri 63105, United States

Phone: 314.854.8000

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a residential area can also cause interference, and in this

case the user is obliged to cover the costs of removing the interference.

 Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

Installation RSPS20/25

Release

09

12/2019

11

About this manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

Documentation mentioned in the “User Manual Installation” that is not

supplied with your device as a printout can be found as PDF files for

downloading on the Internet at: https://www.doc.hirschmann.com

12

Installation RSPS20/25

Release

09

12/2019

Key

The symbols used in this manual have the following meanings:

 Listing

 Work step



Subheading

Installation RSPS20/25

Release

09

12/2019

13

1 Description

1.1 General description

The RSPS20/25 devices are designed for the special requirements of

industrial automation. They meet the relevant industry standards, provide

very high operational reliability, even under extreme conditions, and also

long-term reliability and flexibility.

You can choose from between a wide range of variants. You have the option

to set up your device individually based on different criteria:

 Types of connectors

 Temperature range

 Supply voltage range

 Certifications

 Redundancy functions

You have the option of choosing various media to connect to the end devices

and other network components:

 Multimode optical fiber

 Singlemode optical fiber

 Twisted pair cable

The device is mounted by latching in place on a DIN rail.

The devices work without a fan.

The redundancy concept allows the network to be reconfigured quickly.

There are convenient options for managing the device. Manage your devices

via:

 Web browser

 SSH

 Telnet

 V.24 interface (locally on the device)

 Network management software (for example HiVision)

The Network Management Software Industrial HiVision provides you with

options for smooth configuration and monitoring. You find further

information on the Internet at the Hirschmann product pages:

http://www.hirschmann.com/en/QR/INET-Industrial-HiVision

The device provides you with a large range of functions, which the manuals

for the operating software inform you about. You find these manuals as PDF

files on the Internet at http://www.doc.hirschmann.com

14

Installation RSPS20/25

Release

09

12/2019

The Hirschmann network components help you ensure continuous

communication across all levels of the company.

1.2 Device name and product code

The device name corresponds to the product code. The product code is

made up of characteristics with defined positions. The characteristic values

stand for specific product properties.

You have numerous options of combining the device characteristics. You can

determine the possible combinations using the Configurator which is

available in the Belden Online Catalog https://catalog.belden.com on the web

page of the device.

Item Characteristic Character

istic value

Description

1 ... 4 Product RSPS Rail Switch Power Smart

5 ... 6 Data rate and

hardware type

20 Fast Ethernet switch

25 Fast Ethernet switch with extended redundancy

function

7 (hyphen) –

8 ... 9 Number

Fast Ethernet ports

06 6 ×

10 ... 11 Number

Gigabit Ethernet ports

00 0 ×

12 ... 14 Configuration of the

uplink ports

2T1 2 × RJ45 socket for 10/100 Mbit/s Twisted pair

connections

2Z6 2 × SFP slot for 100 Mbit/s F/O connections

15 ... 16 Configuration of the

other ports

TT 4 × RJ45 socket for 10/100 Mbit/s Twisted pair

connections

YT 2 × SFP slot for 100 Mbit/s F/O connections

2 × RJ45 socket for 10/100 Mbit/s Twisted pair

connections

17 (hyphen) –

18 Temperature range S Standard +32 °F ... +140 °F (0 °C ...

+60 °C)

T Extended −40 °F ... +158 °F (−40 °C ...

+70 °C)

E Extended with

Conformal Coating

−40 °F ... +158 °F (−40 °C ...

+70 °C)

Table 4: Device name and product code

Installation RSPS20/25

Release

09

12/2019

15

19 ... 20 Supply voltage CC 2 voltage inputs for redundant power supply

Rated voltage range DC:

24 V DC ... 48 V DC

K9 1 voltage input

Rated voltage range AC:

110 V AC ... 230 V AC, 50 Hz ... 60 Hz

Rated voltage range DC:

60 V DC ... 250 V DC

M9 1 voltage input

Rated voltage range AC:

110 V AC ... 230 V AC, 50 Hz ... 60 Hz

Rated voltage range DC:

110 V DC ... 250 V DC

21 ... 22 Certificates and

declarations

You will find detailed information on the certificates and

declarations applying to your device in a separate overview.

See table 5 on page 16.

22 ... 23 Customer-specific

version

HS Hirschmann Standard

HM Hirschmann Fast MRP

HP Hirschmann PRP

HH Hirschmann HSR

Note: You can exchange software with each other on the following device variants:

 HM

 HP

 HH

Item Characteristic Character

istic value

Description

Table 4: Device name and product code

16

Installation RSPS20/25

Release

09

12/2019

Application case Certificates and declarations Characteristic value

a

a. X = Certificate or declaration present

(X) = Certificate or declaration in preparation

(x) = Certificate or declaration available upon request

T9 TY U9 UT UX UY V9 VT VU VY X9 Y9 Z9

Standard applications CE X X XXXXXXXXXXX

FCC XXXXXXXXXXXXX

EN 60950-1 X X XXXXXXXXXXX

EN 61131-2 X X XXXXXXXXXXX

UL 508 X XXX XXXXX

UL 60950-1 (X) (X) (X) (X) (X) X (X) (X) (X)

Substation applications IEC61850-3 XXXX

IEEE 1613 XXXX

Oil and gas applications ISA-12.12.01 – Class I, Div. 2 X X

Railway applications (trackside) EN 50121-4 X X X X

Navy applications GL XXXX X

ABS (X) (X) (X) (X) (X)

BV (X) (X) (X) (X) (X)

DNV (X) (X) (X) (X) (X)

LR (X) (X) (X) (X) (X)

Table 5: Assignment: application cases, certificates and declarations, characteristic values

Installation RSPS20/25

Release

09

12/2019

17

1.3 Device views

1.3.1 Front view

Front view:

on the left: Device variants RSPS...........2Z6YT..CC....

on the right: Device variants RSPS...........2Z6TT..M9/K9....

1 LED display elements for device status

2 V.24 interface

3 Uplink ports

2 × SFP slot for 100 Mbit/s F/O connections

4 Other ports

alternatively,

depending on

device variant

Port configuration

characteristic value:

YT

2 × SFP slot for 100 Mbit/s F/O connections

2 × RJ45 socket for 10/100 Mbit/s Twisted pair

connections

Port configuration

characteristic value:

TT

4 × RJ45 socket for 10/100 Mbit/s Twisted pair

connections

5 Grounding screw

1

2

3

4

5

6

7

5

6

7

1

2

3

4

18

Installation RSPS20/25

Release

09

12/2019

6 Supply voltage connection

alternatively,

depending on

device variant

Supply voltage with

the characteristic

value:

CC

 2 voltage inputs for redundant power supply

 2-pin terminal block

Supply voltage with

the characteristic

value:

M9 or K9

 1 voltage input

 3-pin terminal block

7 Connection for the signal contact

Front view of device variants RSPS...........2T1TT........

1 LED display elements for device status

2 V.24 interface

3Uplink ports

2 × RJ45 socket for 10/100 Mbit/s Twisted pair connections

4 Other ports

4 × RJ45 socket for 10/100 Mbit/s Twisted pair connections

5 Grounding screw

1

2

3

4

5

6

7

Installation RSPS20/25

Release

09

12/2019

19

1.3.2 Rear view

6 Supply voltage connection

alternatively,

depending on

device variant

Supply voltage with

the characteristic

value:

CC

 2 voltage inputs for redundant power supply

 2-pin terminal block

Supply voltage with

the characteristic

value:

M9 or K9

 1 voltage input

 3-pin terminal block

7 Connection for the signal contact

1 Slot for the SD card

2 Thumb screw

1

2

20

Installation RSPS20/25

Release

09

12/2019

1.4 Power supply

You will find information on the characteristic values here:

“Device name and product code” on page 14

1.4.1 Supply voltage with the characteristic value M9 or K9

The following options for power supply are available:

 1 × 3-pin terminal block

You will find information on connecting the supply voltage here:

See “Supply voltage with the characteristic value M9 or K9” on page 20.

1.4.2 Supply voltage with the characteristic value CC

The following options for redundant power supply are available:

 2 × 2-pin terminal block

You will find information on connecting the supply voltage here:

See “Supply voltage with the characteristic value CC” on page 20.

1.5 Ethernet ports

You can connect end devices and other segments to the device ports using

twisted pair cables or optical fibers (F/O).

1.5.1 100/1000 Mbit/s twisted pair port (optional)

This port is an SFP slot.

The 100/1000 Mbit/s twisted pair port allows you to connect network

components according to the standard IEEE 802.3 100BASE-TX/

1000BASE-T.

This port supports:

 Autonegotiation

 Full duplex mode

Pin Function

1BI_DB+

2BI_DB−

3BI_DA+

4 BI_DD+

5BI_DD−

6BI_DA−

7 BI_DC+

8BI_DC−

Table 6: Pin assignment of the 10/100/1000 Mbit/s twisted pair port, RJ45 socket,

1000 Mbit/s mode, MDI-X mode

1

2

3

4

5

6

7

8

Page is loading ...

Belden Hirschman RSPS20 User manual

This manual is also suitable for

Belden Hirschman RSPS20 User manual

Related papers

Other documents