Lithonia Lighting BLT4 BLT Best In Value Low Profile LED Luminaire Owner's manual

Brand: Lithonia Lighting

Model: BLT4 BLT Best In Value Low Profile LED Luminaire

Type: Owner's manual

FEATURES & SPECIFICATIONS

INTENDED USE

The RELOC®-Ready Luminaire (RRL) connectors enables a simple and consistent factory installed

option across all ABL luminaire brands. When ordered on a RELOC xture cable (OFC), xture cord

drops (OCS or OCU) and xture drop cables (OD); the line side of the connector will be factory attached

to all the wire leads except for the ground wire. When ordered with the luminaire, the load side of the

connector will be prewired based on the appropriate wiring instruction selection.

ELECTRICAL

• 18 AWG solid wire only; stranded not available.

• Tin-bonded 18 AWG (≤16 strand) acceptable.

• Current Interruption 10 cycles.

SYSTEM FEATURES

• RRL connector used with the OnePass system.

• Load side of connector factory attached to luminaire. Refer to luminaire spec sheet for ordering

information.

• 4-pole mating connector with push-in terminations allows for simple installation.

• Touch-safe design on both halves, meets UL/CSA requirement.

• Wiping contact design allows safe disconnect under load.

LISTINGS

• UL 2459

• CSA- C22.2 NO. 2459

• NEC 2008 410.130(G) Compliant

• CEC 30-308(4) Compliant

1 of 1

Catalog Number

Notes Type

RELOC®-Ready Luminaire

RRL

Universal Fixture Connector

RRL Load Side shown

OD with RRL line side shown OFC with RRL line side shown

RRL

Series Wiring Instructions

ABallast/driver wired to pin position #1 (120V,277V,347V - Phase A)

Ballast/driver wired to pin position #1 & #4 (208V, 240V, 480V - Phase A)

BBallast/driver wired to pin position #2 (120V,277V,347V - Phase B)

Ballast/driver wired to pin position #2 & #4 (208V, 240V, 480V - Phase B)

CBallast/driver wired to pin position #3 ( 120V,277V,347V - Phase C )

AB Outboard ballast/driver wired to pin position #1 (120V,277V,347V - Phase A) 2

Inboard ballast/driver wired to pin position #2 (120V, 277V, 347V - Phase B)

AE Ballast/driver wired to pin position #1 (120V,277V,347V - Phase A)

Emergency ballast/driver wired to pin position #2 (120V,277V,347V - Phase B) 3

ABE Ballast/driver wired to pin position #1 (120V,277V,347V - Phase A) 2

Ballast/driver wired to pin position #2 (120V,277V,347V - Phase B)

Emergency ballast/driver wired to pin position #3 (120V,277V,347V - Phase C) 3

C12S Ballast/driver wired to pin position #1 (120V,277V,347V - Phase A)

Low voltage wire (positive/purple) (data1) wired to pin position #2

Low voltage wire (common/gray) (data2) wired to pin position #3 4

Ballast/driver wired to pin position #1 & #2 (208V, 240V, 480V - Phase A) 4

Low voltage wire (positive/purple) (data1) wired to pin position #2

Low voltage wire (common/gray) (data2) wired to pin position #3 4

22N Ballast/driver wired to pin position #2 and pin position #3 (120V,277V,347V - Phase B)

122N Ballast/driver wired to pin position #1 and #4 (120V,277V,347V - Phase A)

Ballast/driver wired to pin position #2 and #3 (120V,277V,347V - Phase B)

RRL1

• RoHS Compliant

WARRANTY

• 5-year limited warranty. Complete warranty terms located at:

www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx

Actual performance may dier as a result of end-user environment and application.

Note: Specications subject to change without notice.

Load Side RELOC®-Ready Luminaire

NOTES

1. Not available with IBG Haleon sensor options.

2. Not available with LED luminaries. Only compatible with products that are wired

for outboard/inboard control.

3. AE and ABE Commercial xtures should disconnect the TSPL before unplugging

the RRL so it does not go into discharge mode.

4. RRLC12S option is to be used with the OnePass OCU, OCS, OD, OFC and OD for 0-24V

integrated single-circuit or 0-10V low voltage controls applications. Not available

with integral dimming sensors.

Fixture Ordering Example:

IBG 15000LM SEF AFL GND 277 GZ10

40K 80CRI PS30250 RRLAE BPK DWH

FIXTURE ORDERING LOGIC

For shortest lead times, congure product using bolded options.

Line Side RELOC®

Series

RRL

RELOC® Ordering Example:

OFC 277 12/2G 13 RRL G

OCS 480 10 RRL

OD 277 12/3G 15 RRL

RRL

NOTE

1. All hot conductors and neutral wires present in RELOC cable, drop

cable.

2. G option required for OFC xture cables.

3. Ground wire will include poke-in wire connector.

4. Visit RELOC® to order with RELOC systems.

2 of 2

RRL RELOC®-Ready Luminaire

RRL

Position # Function

Standard Wiring Applications

120V,277V,347V

1Hot 1 X X

2Hot 2 X X

3Hot 3 X

4Neutral XXXX

Wiring Instruction RRLA RRLB RRLC RRLAB

DIMENSIONS

Dimensions are shown in inches (millimeters)

LOAD SIDE

Connects to Fixture. Installed on

xture at factory or by customer.

LINE SIDE

Connects to RELOC Fixture Cable.

Installed on Reloc cable at the factory.

WIRING INSTRUCTIONS

Pin position and conductor functions by voltage.

Position # Function

Normal and Emergency

Applications 120V, 277V, 347V

1Hot 1 X X

2Hot 2 X X

3Hot 3 X

4Neutral X X

Wiring Instruction RRLAE RRLABE

Position # Function

Class I Class II Wiring Ap-

plications 120V, 277V

1Hot 1 X

2 Data 1, Positive ( + ) X

3 Data 2, Common ( - ) X

4Neutral X

Wiring Instruction RRLC12S

Position # Function

Two Neutral Applications

120V, 277V, 347V

1Hot 1 X

2Hot 2 X X

3 Neutral 2 X X

4Neutral 1 X

Wiring Instruction RRL22N RRL122N

Position # Function

Special Industrial Voltage

Applications 208V, 240V, 480V

1Hot 1 X

2Hot 2 X

3Hot 3

4Hot 4 X X

Wiring Instruction RRLA RRLB

Position # Function

Class I Class II Wiring

Applications 208V, 240V, 480V

1Hot 1 X

2 Data 1, Positive ( + ) X

3Data 2, Common ( - ) X

4Hot 2 X

Wiring Instruction RRLC12S

Lithonia Lighting BLT4 BLT Best In Value Low Profile LED Luminaire Owner's manual

Lithonia Lighting BLT4 BLT Best In Value Low Profile LED Luminaire Owner's manual

Lithonia Lighting BLT4 BLT Best In Value Low Profile LED Luminaire Owner's manual

Related papers

Other documents