OWNERS MANUAL
BIGHORN PRODUCTS
PO BOX 609
SALEM , SD 57058
www.bighornstabilizer.com
Ph:(833) 582-1170 or (605) 271-4632
US Patent No. 10,883,310 B2
2
SECTION 1: TOP LEVEL ASSEMBLY—EXPLODED VIEW
ITEM NO. DESCRIPTION QTY
1 LADDER SLEEVE - LEFT SIDE 1
2 LADDER SLEEVE- RIGHT SIDE 1
3 FOOT ADJUSTMENT TUBE 2
4 FORMED HANDRAIL 2
5 8" CONNECTING TUBE-SS 2
6 LADDER SLEEVE CAP 2
7 1/4" HEX SCREW 2
8 1/4" NYLON NUT 2
9 CLEVIS PIN 4
10 THUMB SCREW FASTENER 6
3
ITEM 2 (QTY1)
LADDER SLEEVE– RIGHTSIDE
ITEM 1 (QTY1)
LADDER SLEEVE– LEFT SIDE
ITEM 5 (QTY2)
8” CONNECTING TUBE—SS
SECTION 2: PARTS BREAKDOWN
ITEM 3 (QTY2)
FOOT ADJUSTMENT TUBE
ITEM 4 (QTY2)
FORMED HANDRAIL
4
ITEM 9 (QTY4)
CLEVIS PIN ITEM 10 (QTY6)
3/8” THUMB SCREW
SECTION 2: PARTS BREAKDOWN
ITEM 6 (QTY2)
SLEEVE CAP
ITEM 8 (QTY4)
1/4” NYLON NUT
ITEM 7 (QTY4)
1/4” HEX SCREW
5
SECTION 3: ASSEMBLY INSTRUCTIONS
Tools Needed: 5/16” wrench & 3/16” Allen wrench
STEP 1
Assemble 8” connecng tube (item 5) with Ladder sleeve –le side & Ladder sleeve—right side (Item 1 &
2) as shown in gure 1.
Align 8” connecng tube (item 5) holes with Ladder sleeve (Items 1 & 2) holes and insert 1/4” hex screw
(Item 7) and secure by ghtening 1/4” Nylon nut (Item 8).
FIGURE 1: 8” connecng tube installaon
ASSEMBLY PROCESS IS PERFORMED ON THE GROUND
6
SECTION 3: ASSEMBLY INSTRUCTIONS
STEP 3
Aach formed handrail (Item 4) with handrail extension (item 3) for both right & le ladder sleeves.
Align formed handrail (Item 4) holes with handrail extension (item 3) holes. Secure both formed hand-
rail with clevis pin in hole closest to ladder foot. Precise adjustment will be calibrated in step 5.
STEP 2
Aach formed handrail (Item 4) with 8” connecng tube (item 5) for both right & le ladder sleeves.
Align formed handrail (Item 4) holes with 8” connecng tube (item 5) holes such that the formed hand-
rail orients itself as shown in the gure 2. Secure both formed handrails with clevis pin (Item 9).
FIGURE 2: Formed Handrail installaon
FIGURE 3: Foot Adjustment Tube installaon
7
STEP 4
Aach Right and Le Ladder sleeve assembly’s on the top end of ladder. Formed handrail needs to face
the structure or building such that the rubber pad on ladder sleeves can rest as a contact point.
Slide right and le ladder sleeve assembly's unl spring ladder hook is fastened behind the top ladder
rung as shown in gure 4.
Tighten thumb screws (Item 10) to secure Bighorn Stabilizer to ladder in the order as labeled in gure 4
for both right and le assembly’s. Thumb screws will contact inside plate as shown in the secon view
for thumbscrews 2 and 3 only. Thumbscrew no. 1 will contact the ladder directly (Do NOT over ghten).
Ladder Sleeve Caps (Item 6) can be removed should your ladder have factory molded end caps installed.
SECTION 3: ASSEMBLY INSTRUCTIONS
Finger ghten thumb screws only.
Over ghtening may result in damage to ladder.
FIGURE 4: Ladder sleeve installaon
SECTION VIEW: Thumb screw
8
SECTION 4: SAFETY INSTRUCTIONS
Adhere to OSHA recommended standard 4:1 rao 1910.23 for all ladder use.
The base of the ladder should extend 1 foot for every 4 feet of height between the working surface
and the point of contact as shown in gure 5 . When done correctly, the ladder will meet the ground
at a 75-degree angle.
An extension or straight ladder used to access an elevated surface must extend at least 3 feet above
the point of support as shown in gure 5 & 6. A ladder extended to a height of 48 feet or longer re-
quires a 6 foot extension beyond the eave.
FIGURE 6: Ladder Bridge Adherence FIGURE 5: OSHA recommended standard 4:1 rao, 1910.23
Adhere to all warning labels provided by ladder
manufacturer
9
SECTION 4: SAFETY INSTRUCTIONS
Adhere to all warning labels provided by ladder
manufacturer
10
SECTION 5: LADDER BRIDGE USAGE
STEP 5
With Ladder Bridge assembly complete and mounted on ladder, Place ladder against structure or building
such that rubber padding on sleeve assembly’s are facing the structure or building as shown in gure 7.
Aer ladder is securely posioned, climb to top of ladder to place guer hooks inside guer and adjust
foot adjustment tube (item 8) to plaorm of roof as shown in gure 7 below. MUST make ght contact to
the roof as to apply downward pressure. Insert clevis pins in appropriate hole.
For new construcon/bare roof screw foot to bare roof using screw for a more permanent mount.
Enjoy a safe and secure transion to the roof!
FIGURE 7: Ladder Usage
Not designed as an anchor point. Do not
e o to any part of the ladder bridge
11
SECTION 5: LADDER BRIDGE USAGE
STEP 6
Storage and Travel
Ladder Bridge assemblies can be removed from ladder for storage or travel.
Ladder bridge assemblies can be kept on ladder and folded in for travel and storage as shown in gure 8.
FIGURE 8: Travel Mode
12
Warranty
BIGHORN STABILIZER warrants the product to be free of defects in materials and work-
manship for a period of one full year from the date of purchase by the original purchaser.
This limited warranty is valid with the completion of the warranty registration card (included in
the packaging) and is returned to BIGHORN STABILIZER by mail or online
at www.bighornstailizer.com within 30 days from the date of purchase.
During the warranty period, BIGHORN STABILIZER reserves the right at its own discretion to
repair or replace defective parts using new or refurbished parts.
This limited warranty is valid only with the original purchaser and is not transferable.
This limited warranty does not cover any problem that is caused by conditions, malfunctions or
damage not resulting from defects in materials and workmanship.
BIGHORN STABILIZER will not have any liabilities for incidental or consequential dam-
ages caused by the misuse or mishandling of the product.
To obtain warranty service, you must first contact us to determine the problem and the most ap-
propriate solution for you. Your purchase receipt will be required for warranty service.
Return Policy
RETURNS
The original purchaser has 30 days to return an item from the date it was received.
To be eligible for a return, your item must be unused and in the same condition that you re-
ceived it and in the original packaging.
Your items, original receipt, or proof of purchase along with a brief written explanation of
why the product is being returned will be required.
Once we receive your item, we will inspect it and notify you on the status of the refund.
If your item is approved, we will initiate a refund to your credit card (or original method of
payment).
SECTION 6: WARRANTY & RETURN POLICY
13
SHIPPING
You must obtain a return authorizaon number prior to returning your item. Please contact us via
the following email address: returns@bighornstabilizer.com
You will be responsible for shipping costs for your returned item. Shipping costs are non-refundable.
If you receive a refund, the cost of the return shipping will be deducted from your refund.
There may be a handling and restocking fee for your returned item.
CONTACT US
If you have any quesons on how to return your item, please contact us.
SECTION 6: WARRANTY & RETURN POLICY
BIGHORN PRODUCTS
PO BOX 609
SALEM , SD 57058
www.bighornstabilizer.com
Ph:(833) 582-1170 or (605) 271-4632
Email: returns@bighornstabilizer.com
US Patent No. 10,883,310 B2
Made in INDIA
14
SECCIÓN 1: MONTAJE DE NIVEL SUPERIOR - VISTA DESPIECE
ARTÍCULO NO. Descripción candad
1 MANGUITO ESCALERA - LADO IZQUIERDO 1
2 MANGUITO DE ESCALERA - LADO DERECHO 1
3 TUBO DE AJUSTE DEL PIE 2
4 PASAMANOS FORMADO 2
5 8 "CONECTANDO TUBO-SS 2
6 TAPA DE ESCALERA 2
7 TORNILLO HEXAGONAL DE 1/4 " 2
8 TUERCA DE NYLON DE 1/4 " 2
9 PASADOR DE HORQUILLA 4
10 SUJETADOR DE TORNILLO PULGAR 6
15
ARTÍCULO 2 (candad 1)
MANGUITO DE ESCALERA
- LADO DERECHO
ARTÍCULO 1 (candad 1)
MANGUITO ESCALERA
- LADO IZQUIERDO
ARTÍCULO 5 (candad 2)
8 "CONECTANDO TUBO-SS
SECCIÓN 2: DESGLOSE DE PIEZAS
ARTÍCULO 3 (candad 2)
TUBO DE AJUSTE DEL PIE
ARTÍCULO 4 (candad 2)
PASAMANOS FORMADO
16
ARTÍCULO 9 (candad )
PASADOR DE HORQUILLA
ARTÍCULO 10 (candad 6)
SUJETADOR DE TORNILLO PULGAR
SECCIÓN 2: DESGLOSE DE PIEZAS
ARTÍCULO 6 (candad 2)
TAPA DE ESCALERA
ARTÍCULO 8 (candad 4)
TUERCA DE NYLON DE 1/4 "
ARTÍCULO 7 (candad 4)
TORNILLO HEXAGONAL DE 1/4 "
17
SECCIÓN 3: INSTRUCCIONES DE MONTAJE
Herramientas necesarias: llave de 5/16" y llave Allen de 3/16"
PASO 1
Ensamble el tubo de conexión de 8 ”(arculo 5) con el manguito de la escalera - lado izquierdo y el
manguito de la escalera - lado derecho (Arculo 1 y 2) como se muestra en la gura 1.
Alinee los oricios del tubo de conexión de 8 ”(elemento 5) con los oricios de la manga de la escalera
(elementos 1 y 2) e inserte el tornillo hexagonal de 1/4” (elemento 7) y asegúrelo apretando la tuerca
de nailon de 1/4 ”(elemento 8).
FIGURA 1: Instalación del tubo de conexión de 8 ”
EL PROCESO DE MONTAJE SE REALIZA EN EL TERRENO
18
SECCIÓN 3: INSTRUCCIONES DE MONTAJE
PASO 3
Fije el pasamanos formado (arculo 4) con la extensión del pasamanos (arculo 3) para las mangas de la
escalera derecha e izquierda.
Alinee los oricios formados del pasamanos (elemento 4) con los oricios de la extensión del pasa-
manos (elemento 3). Asegure ambos pasamanos formados con un pasador de horquilla en el oricio
más cercano al pie de la escalera. El ajuste preciso se calibrará en el paso 5.
PASO 2
Fije el pasamanos formado (arculo 4) con un tubo de conexión de 8 ”(arculo 5) para las mangas de la
escalera derecha e izquierda.
Alinee los oricios del pasamanos formado (arculo 4) con los oricios del tubo de conexión de
8”(arculo 5) de manera que el pasamanos formado se oriente como se muestra en la gura 2. Asegure
ambos pasamanos formados con un pasador de horquilla (arculo 9).
FIGURA 2: Instalación de pasamanos formado
FIGURA 3: Instalación del tubo de ajuste del pie
19
PASO 4
Coloque el ensamblaje de la manga de la escalera derecha e izquierda en el extremo superior de la
escalera. El pasamanos formado debe estar orientado hacia la estructura o el edicio de manera que la
almohadilla de goma de las mangas de la escalera pueda descansar como un punto de contacto.
Deslice el ensamblaje de la manga de la escalera derecha e izquierda hasta que el gancho de la escalera
de resorte esté sujeto detrás del peldaño superior de la escalera como se muestra en la gura 4.
Apriete los tornillos de mariposa (arculo 10) para asegurar el estabilizador Bighorn a la escalera en el
orden que se indica en la gura 4 para los conjuntos derecho e izquierdo. Los tornillos de mariposa en-
trarán en contacto con la placa interior como se muestra en la vista en sección para los tornillos de mar-
iposa 2 y 3 únicamente. Tornillo de mariposa no. 1 entrará en contacto con la escalera directamente
(NO apriete demasiado).
Las tapas de la manga de la escalera (arculo 6) se pueden quitar si su escalera ene tapas de extremo
moldeadas de fábrica instaladas.
SECCIÓN 3: INSTRUCCIONES DE MONTAJE
Apriete los tornillos de mariposa con los dedos
únicamente. Apretar demasiado puede dañar la
escalera.
FIGURA 4: Instalación de la manga de escalera
VISTA DE LA SECCIÓN: Tornillo de mariposa
20
SECCIÓN 4: INSTRUCCIONES DE SEGURIDAD
Adhiérase a la proporción estándar 4: 1 recomendada por OSHA 1910.23 para todo uso de escaleras.
La base de la escalera debe extenderse 1 pie por cada 4 pies de altura entre la supercie de trabajo
y el punto de contacto como se muestra en la gura 5. Cuando se hace correctamente, la escalera se
encontrará con el suelo en un ángulo de 75 grados.
Una extensión o escalera recta ulizada para acceder a una supercie elevada debe extenderse al
menos 3 pies por encima del punto de apoyo como se muestra en las guras 5 y 6. Una escalera ex-
tendida a una altura de 48 pies o más requiere una extensión de 6 pies más allá del alero.
FIGURA 6: Adherencia del puente de FIGURA 5: Relación estándar recomendada de OSHA 4: 1,
Adhiera a todas las equetas de advertencia
proporcionadas por la escalera
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
