Engine
Printable View (831 KB)
Installation
All vehicles
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
2. Raise the engine high enough to clear the No. 1 crossmember, then position the engine into the vehicle.
Vehicles with automatic transmission
3. Align the torque converter studs with the holes in the engine flywheel, then lower the engine onto the engine mount towers.
Vehicles with manual transmission
4. Lower the engine onto the engine mount towers.
All vehicles
5. Remove the Heavy Duty Floor Crane and the Diesel Engine Lifting Bracket.
Vehicles with automatic transmission
SECTION 303-01C: Engine — 6.0L Diesel 2005 F-Super Duty 250-550 Workshop Manual
INSTALLATION
Procedure revision date: 04/07/2005
Special Tool(s)
Diesel Engine Lifting Bracket
(D83T-6000-B) 303-D043
Adapter for 303-D043
303-D043-02
Adapter for 303-D043
303-D043-01
Heavy Duty Floor Crane
014-00071
Wrench, Fan Clutch Nut
303-591
Material
Item Specification
SAE 15W-40 Super Duty Motor Oil
XO-15W40-QSD or equivalent
WSS-M2C171-D
Motorcraft Premium Gold Engine Coolant
VC-7-A (in California, Oregon and New Mexico VC-7-B, in Canada CVC-
7-A)
WSS-M97B51-
A1
R-134a Refrigerant
YN-19
WSH-M17B19-A
High Temperature Nickel Anti-Seize Lubricant
XL-2
ESE-M12A4-A
Page
1
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
6. Remove the transmission jack.
7. Install the transmission-to-engine mounting bolts.
8. Install the new torque converter-to-flywheel retaining nuts.
9. Install the flywheel housing cover.
All vehicles
10. NOTE: RH shown, LH similar.
Install the LH and RH side engine mount retaining nuts.
11. Remove the engine lifting eye from the right side cylinder head.
12. Install the manufacturer's lifting bracket.
Page
2
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
13. Remove the two engine lift adapters.
14. Position the turbocharger outlet pipe.
15. Install the transmission cooler tube bracket and nut.
16. Install the left rear valve cover stud.
17. Install the fuel injector control module bracket and nuts.
Page
3
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
Late build vehicles
18. Connect the exhaust pressure sensor tube fitting to the exhaust manifold and install the exhaust pressure sensor retaining nut.
19. Install the heat shield and bolts.
20. Position the turbocharger adapter pipes. Install the gasket and bolts.
All vehicles
21. NOTE: To aid in installation, make sure the turbocharger Marmon clamp stud is positioned toward the drivers side.
Position the turbocharger adapter pipe.
22. NOTE: Left side shown, right side similar.
NOTE: Use a half-moon wrench to aid in accessing the fasteners.
NOTE: Apply anti-seize lubricant to the threads prior to installing the bolts.
Loosely install the bolts for the turbocharger adapter pipe.
Page
4
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
23. Position back the block heater and starter wiring.
24. Connect the block heater electrical connector.
25. Connect the starter wiring and install the solenoid cap.
26. Connect the ground strap on the right head and install the bolt.
Vehicles with automatic transmission
27. Install the automatic transmission fluid indicator and tube.
All vehicles
28. Position back the wiring and connect the crankshaft position (CKP) sensor electrical connector.
Page
5
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
Vehicles with A/C
29. Install the A/C compressor and bolts.
30. Remove the cap or plug and install a new O-ring seal. Install the A/C hose and retaining nut.
31. Connect the A/C high-pressure switch and the clutch electrical connectors.
All vehicles
32. Connect the RH glow plug electrical connector and wire retainer.
33. Connect the glow plug module electrical connectors. Connect the pushpin retainer and the injection control pressure (ICP) sensor electrical connector.
Page
6
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
34. NOTE: Only one retainer shown.
Connect the wire retainers on the valve cover studs.
35. Connect the ground cable and the ground stud.
36. Install the battery cable bracket and the nut.
37. Position the power steering pump and install the lower bolt.
38. Install the power steering pump upper bolts.
Page
7
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
39. NOTE: Only one standoff shown.
Install the stator standoffs.
40. Connect the fuel lines and install the clips. For additional information, refer to Section 310-00.
41. Install the lower radiator hose and clamp.
42. Connect the heater hose at the front cover.
43. Connect the camshaft position (CMP) sensor electrical connector.
Page
8
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
44. Connect the 12-pin and 8-pin electrical connectors.
45. Connect the powertrain control module (PCM) electrical connector.
46. Connect the LH glow plug electrical connector.
47. Install the battery tray and bolts.
48. Install the intake manifold. For additional information, refer to Intake Manifold in this section.
49. Tighten the nuts at the turbocharger adapter pipe flange.
Page
9
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
50. Install the upper radiator support and bolts.
51. NOTE: Cover position back for clarity.
Connect the body feed cable and install the retaining nut.
52. Install the transmission oil cooler.
53. NOTE: Remove the caps or plugs as needed.
Connect the transmission cooler hoses.
54. Install the power steering cooler and bolts.
Page
10
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
55. Position back the power steering cooler tubes and install the tubes in the retaining clip.
56. NOTE: Remove the caps or plugs as needed.
Connect the power steering hoses and tighten the clamps.
57. Install the front bumper.
58. Install the radiator grille opening panel reinforcement. For additional information, refer to Section 501-02.
Vehicles with A/C
59. Install the A/C condenser assembly. For additional information, refer to Section 412-01.
All vehicles
60. Install the charge air cooler. For additional information, refer to Section 303-12.
61. Install the air cleaner assembly. For additional information, refer to Section 303-12.
62. Install the cooling fan stator. For additional information, refer to Section 303-03.
Vehicles with manual transmission
63. Install the clutch disc and pressure plate. For additional information, refer to Section 308-01.
64. Install the transmission. For additional information, refer to Section 308-03.
All vehicles
65. Fill the motor with clean engine oil.
66. Connect the LH and RH battery cables. For additional information, refer to Section 414-01.
67. Fill the cooling system. For additional information, refer to Section 303-03.
68. Cycle the key three times prior to starting the vehicle to avoid the possibility of air lock in the fuel system.
69. Fill and bleed the power steering system. For additional information, refer to Section 211-00.
70. Check and fill the transmission.
Page
11
of
11
2005 F
-
Super Duty 250
-
550 Workshop Manual
1/4/2010
http://www.fordtechservice.dealerconnection.com/pubs/content/~WS5O/~MUS~LEN/20/S5
...
/
