Page is loading ...
Page 2
Thank you for purchasing this Hampton Bay Four Light Bath Fixture.
This product has been manufactured with the highest standards of safety
and quality.
1. Easy to install.
2. For energy savings this fixture has been engineered to safely use a
Self Ballasted Compact Fluorescent Lamp in place of an
incandescent lamp.
FEATURES:
Before returning to your local Home Depot, please call our Customer
Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU (108-898) or UPC (046335943230).
QUESTIONS, PROBLEMS, MISSING PARTS:
Page 3
TOOLS REQUIRED FOR INSTALLATION AND ASSEMBLY
(not included):
CAUTION:
1. Before starting installation of this fixture or removal of a previous
fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY
ELECTRICAL QUESTIONS. If you have any non-electrical
questions about this fixture, please call our Customer Service Team at
1-877-527-0313 or visit www.homedepot.com. Please reference your
SKU (108-898) or UPC (046335943230).
3. KEEP your receipt and these Instructions for Proof of Purchase.
Safety
goggles
Wire
strippers
Phillips
screwdriver
Electrical
tape
Wire
cutters
4 Light Bulbs (100
watt maximum or
CFL equivalent)
Drill ¼” Drill
bit
Pencil
Hammer
Level
Page 4
1 ea Main Fixture
Body (#1)
PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
ASSEMBLY INSTRUCTIONS:
1. Carefully unpack the fixture. Lay out all parts on a clean surface.
2. Before continuing Assembly please proceed to the Installation Instructions.
3. Connect the Fixture Ground Wire (#18) and the Supply Ground Wire (#19) together
using a Wire Nut (#17). (Fig. 1)
4. Place the Main Fixture Body (#1) over the Wall Plate (#7). Slide the Socket Cups (#4)
over the Sockets (#3), to secure the Main Fixture Body (#1) onto the Wall Plate (#7).
(Fig. 1)
5. Install up to a 100 watt Light Bulb (#22) or Listed SBCFL (Self-Ballasted Compact
Fluorescent Lamp [not provided]) in each Socket (#3) of the Main Fixture Body (#1).
Do not exceed a 100 watt incandescent light bulb, or a 26 watt SBCFL. (Fig. 2)
4 ea Socket
Cups (#4)
Page 5
1. Main
Fixture Body
ASSEMBLY:
3. Socket
4. Socket Cup
22. Light Bulb
1. Main
Fixture Body
3. Socket
Fig. 1
Fig. 2
18.Fixture Ground Wire
19.Supply Ground Wire
17.Wire Nut
Top View
Page 6
PARTS INCLUDED FOR INSTALLATION (parts are not to
scale):
2 ea Wall
Anchors (#9)
2 ea Ball Nuts
(#21)
3 ea Wire
Nuts (#17)
2 ea Outlet Box
Screws (#12)
1 ea Wall Plate (#7)
INSTALLATION INSTRUCTIONS:
1. Place the Wall Plate (#7) over the Outlet Box (#6), aligning the mounting slots of the Wall Plate (#7) with the mounting holes
of the Outlet Box (#6), as shown. Use a level to make sure the Wall Plate (#7) is straight. (Fig. 3)
2. Mark the location of the Keyhole Slots (#8) of the the Wall Plate (#7) onto the wall. Remove the Wall Plate (#7) from the
wall. (Fig. 3)
3. Drill a ¼” hole at the narrow end of each Keyhole Slot (#8) marking on the wall. Carefully hammer a Wall Anchor (#9) into
each Drilled Hole (#10). (Fig. 3)
4. Attach the Black Supply Wire (#13) to the Black Fixture Wire (#14) and the White Supply Wire (#15) to the White Fixture
Wire (#16) using Wire Nuts (#17). (Fig. 3) Wrap all wire connections with electrical tape for a more secure connection.
Note: If you have electrical questions, consult your local electrical code for approved grounding methods.
5. Feed the Supply Ground Wire (#19) through the Wire Hole (#20) of the Wall Plate (#7). (Fig. 3)
6. Replace the Wall Plate (#7) over the Outlet Box (#6), aligning the narrow end of each Keyhole Slot (#8) with its respective
Wall Anchor (#9). Feed the Anchor Screws (#11) through the Keyhole Slots (#8) and thread them into the Wall Anchors (#9)
until the Wall Plate (#7) is flush against the wall. Additionally, feed the Outlet Box Screws (#12) through the mounting slots
of the Wall Plate (#7) and thread them into the mounting holes of the Outlet Box (#6), as shown. Pull the power supply wires
out from the Outlet Box (#6) and through the center hole of the Wall Plate (#7). (Fig. 3)
7. Please proceed back to the Assembly Instructions.
8. Installation is complete. Turn on power at the circuit breaker or fuse box. Turn the light switch on to activate the fixture.
2 ea Anchor
Screws (#11)
8. Keyhole Slot
9. Wall Anchor
10.Drilled Hole
11.Anchor Screw
12.Outlet Box
Screw
13.Black Supply Wire
14.Black Fixture Wire
15.White Supply Wire
16.White Fixture
Wire
17.Wire Nut
20.Wire Hole
INSTALLATION:
19. Supply
Ground Wire
7. Wall Plate
6. Outlet Box
Page 7
Fig. 3
Possible Cause Corrective Action
1. Power is off. 1. Make sure power supply is on.
2. Faulty switch. 2. Test or replace switch.
1. Bulb is burned out 1. Replace light bulb.
2. Faulty wire connection. 2. Check wiring.
Fuse blows or circuit breaker
trips when light is turned on.
1. Crossed wires or power wire is grounding
out.
1. Check wire connections.
Bulb will not turn on.
Lights will not turn on.
TROUBLESHOOTING:
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean
water, never a solvent) to wipe the surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the
circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly
dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the
fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft
cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a
period of five (5) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of of the product at
the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect or mishandling. This warranty shall not apply to any product
that is found to have been improperly installed, set-up, or used in any way not in accordance with the
instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of
an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to
faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product,
such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not
warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a
particular purpose, other than the warranty contained herein. The manufacturer specifically
disclaims any liability and shall not be liable for any consequential or incidental loss or damage,
including but not limited to any labor/expense costs involved in the replacement or repair of said
product.
Page 8
MANUAL DE INSTRUCCIONES
LUMINARIO PARA BAÑO DE QUATRO LUCES
HOME DEPOT SKU# 108-898 (UPC# 046335943230)
Page 9
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
MODE D’INSTALLATION
APPLIQUE DE SALLE DE BAIN
À CUATRO LUMIÈRES
HOME DEPOT UGS N° 108-898 (CUP N° 046335943230)
Page 17
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
