Home Decorators Collection HB7262A-293 Installation guide

HOME

DECORATORS

C O L L E C T I O N

Exterior Wall Lantern

Leeds

OMSID 204294436

(Mystic Bronze Finish)

INSTRUCTION MANUAL

Page 1

HB7362A-293 E/S/F

Thank you for purchasing this Home Decorators Collection exterior

light fixture. This product has been manufactured with the highest

standards of safety and quality.

FEATURES:

1. Exterior Incandescent Wall Lantern in Mystic Bronze Finish.

2. Timeless elegant design.

3. Solid cast aluminum resists elements.

4. For energy savings this fixture has been engineered to safely use a

Self Ballasted Compact Fluorescent Lamp in place of an

incandescent lamp.

5. Easy to assemble and install.

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local Home depot, please call our Customer

Service Team at 1-800-986-34600 or visit www.homedepot.com. Please

reference your OMSID (204294436 Mystic Bronze Finish fixture).

Page 2

CAUTION:

1. Before starting installation of this fixture or removal of a previous

fixture, disconnect the power by turning off the circuit breaker or

by removing the fuse at the fuse box.

2. CONSTULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY

ELECTRICAL QUESTIONS.

3. If you have any non-electrical questions about this fixture, please

contact our Customer Service Team at 1-800-986-3460 or visit

www.homedepot.com. Please reference your OMSID (204294436

Mystic Bronze Finish fixture).

4. Keep your receipt and these Instructions for Proof of Purchase.

TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION

(not included):

Page 3

Exterior Silicon

Rubber Sealant

Wire Strippers

Wire Cutters

Safety Glasses Electrical Tape

Light Bulb (100 W Max.

or CFL equivalent)

Phillips Screwdriver Flathead Screwdriver

PARTS INCLUDED (parts are not to scale):

Page 4

(3) Wire Nuts

(2) Bracket

Mounting Screws

(2) Fixture

Mounting Screws

(1) Mounting Bracket (2) Hex Nuts(2) Lock Nuts

(2) Cage Screws

(1) Fixture Body (1) Cage

INSTALATION & ASSEMBLY:

1. Carefully unpack the fixture. Lay out all parts on a clean surface.

2. Thread the Fixture Mounting Screws (#6) into the provided holes of the

Mounting Bracket (#7) as shown. Thread the Hex Nuts (#9) onto the Fixture

Mounting Screws (#6), as shown. Do not tighten the Hex Nuts (#9) at this

time.

3. Pull the power supply wires out from the Outlet Box (#4), and mount the

Mounting Bracket (#7) to the Outlet Box (#4), using the Bracket Mounting

Screws (#8).

4. Attach the Black Supply Wire (#5) to the Black Fixture Wire (#12) and the

White Supply Wire (#16) to the White Fixture Wire (#13) using Wire Nuts

(#14). Connect the Fixture Ground Wire (#11) and the Supply Ground Wire

(#15) together using a Wire Nut (#14). Wrap all wire connections with

electrical tape for a more secure connection. Note: If you have electrical

questions, consult your local electrical code for approved gro unding methods.

Page 5

10. Wall

Plate

13. White

Fixture Wire

11. Fixture

Ground Wire

14. Wire

Nut

5. Black

Supply

Wire

4. Outlet

Box

7. Mounting

Bracket

8. Bracket

Mounting

Screw

9. Hex

Nut

6. Fixture

Mounting

Screw

16. White

Supply Wire

15. Supply

Ground Wire

12. Black

Fixture Wire

Fig. 1

3. Lock

Nut

Page 6

INSTALLATION & ASSEMBLY (cont.):

5. Place the Wall Plate (#10) over the Outlet Box (#4) and onto the Fixture

Mounting Screws (#6), and adjust the Fixture Mounting Screws (#6) until

they protrude out from the Wall Plate (#10) 1/4". Remove the Wall Plate

(#10) and secure the position of the Fixture Mounting Screws (#6) by

tightening the Hex Nuts (#9) against the Mounting Bracket (#7). Place the

Wall Plate (#10) back onto the Fixture Mounting Screws (#6), and secure it

into place using the Lock Nuts (#3) provided.

6. After installing the fixture, caulk the upper

2/3s of the Wall Plate (#10) to mounting

surface. Leave the bottom 1/3 un-caulked

for drainage of any water that might leak

drainage of any water that might leak into

the enclosure. The manufacturer

recommends a non-drying exterior caulking

material. A good example is a clear silicone

rubber sealant for exterior use.

7. Install up to a 100 watt Light Bulb (#2) or

Listed SBCFL (Self-Ballasted Compact

Fluorescent Lamp [not provided]) in the

socket of the Main Fixture Body (#1). Do

not exceed a 100 watt incandescent light

bulb, or a 26 watt SBCFL.

8. Attach the Cage to the Main Fixture Body

using the provided Cage Screws.

9. Installation is complete. Turn on power at

the circuit breaker or fuse box. Turn the

light switch on to activate the fixture.

Fig. 2

Page 7

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use

clean water, never a solvent) to wipe the glass and surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning off

the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly

dampened clean cloth (use clean water, never a solvent) to wipe the inside glass and

interior surface of the fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry

soft cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a

period of three (3) years from date of purchase. This warranty applies only to the original consumer

purchaser and only to products used in normal use and service. If this product is found to be defective, the

manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement for the product at

the manufacturer’s discretion, provided that the product ahs not been damaged through misuse, abuse,

accident, modifications, alterations, neglect, or mishandling. This warranty shall not apply to any product

that is found to have been improperly installed, set-up, or used in any way not in accordance with the

instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of

an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to

faculty material or workmanship. This warranty shall not apply to the finish on any portion of the product,

such as surface and/or weathering, as this is considered normal wear and tear.

The manufacturer does not warrant and specially disclaims any warranty, whether express or implied

of fitness for a particular purpose, other than the warranty contained herein. The manufacture

specifically disclaims any liability and shall not be liable for any consequential or incidental loss or

damage, including but not limited to any labor/expense cost involved in the replacement or repair of

said product.

Symptom Possible Cause Corrective Action

1. Power is off. 1. Make sure power supply is on.

2. Faulty switch. 2. Test or replace switch.

3. Faulty wire connection. 3. Check wiring.

Fuse blows or circuit breaker

trips when light is turned on.

1. Crossed wires or power wire is grounding

out.

1. Check wire connections.

Light will not turn on.

Page is loading ...

Home Decorators Collection HB7262A-293 Installation guide

Home Decorators Collection HB7262A-293 Installation guide

in other languages

Related papers

Other documents