Hampton Bay HB2051-35 Installation guide

Page is loading ...

Page 2

Thank you for purchasing this Hampton Bay Four Light Bath Fixture.

This product has been manufactured with the highest standards of safety

and quality.

1. Easy to install.

2. For energy savings this fixture has been engineered to safely use a

Self Ballasted Compact Fluorescent Lamp in place of an

incandescent lamp.

FEATURES:

Before returning to your local Home Depot, please call our Customer

Service Team at 1-877-527-0313 or visit www.homedepot.com. Please

reference your SKU (108-898) or UPC (046335943230).

QUESTIONS, PROBLEMS, MISSING PARTS:

Page 3

TOOLS REQUIRED FOR INSTALLATION AND ASSEMBLY

(not included):

CAUTION:

1. Before starting installation of this fixture or removal of a previous

fixture, disconnect the power by turning off the circuit breaker or by

removing the fuse at the fuse box.

2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY

ELECTRICAL QUESTIONS. If you have any non-electrical

questions about this fixture, please call our Customer Service Team at

1-877-527-0313 or visit www.homedepot.com. Please reference your

SKU (108-898) or UPC (046335943230).

3. KEEP your receipt and these Instructions for Proof of Purchase.

Safety

goggles

Wire

strippers

Phillips

screwdriver

Electrical

tape

Wire

cutters

4 Light Bulbs (100

watt maximum or

CFL equivalent)

Drill ¼” Drill

bit

Pencil

Hammer

Level

Page 4

1 ea Main Fixture

Body (#1)

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

ASSEMBLY INSTRUCTIONS:

1. Carefully unpack the fixture. Lay out all parts on a clean surface.

2. Before continuing Assembly please proceed to the Installation Instructions.

3. Connect the Fixture Ground Wire (#18) and the Supply Ground Wire (#19) together

using a Wire Nut (#17). (Fig. 1)

4. Place the Main Fixture Body (#1) over the Wall Plate (#7). Slide the Socket Cups (#4)

over the Sockets (#3), to secure the Main Fixture Body (#1) onto the Wall Plate (#7).

(Fig. 1)

5. Install up to a 100 watt Light Bulb (#22) or Listed SBCFL (Self-Ballasted Compact

Fluorescent Lamp [not provided]) in each Socket (#3) of the Main Fixture Body (#1).

Do not exceed a 100 watt incandescent light bulb, or a 26 watt SBCFL. (Fig. 2)

4 ea Socket

Cups (#4)

Page 5

1. Main

Fixture Body

ASSEMBLY:

3. Socket

4. Socket Cup

22. Light Bulb

1. Main

Fixture Body

3. Socket

Fig. 1

Fig. 2

18.Fixture Ground Wire

19.Supply Ground Wire

17.Wire Nut

Top View

Page 6

PARTS INCLUDED FOR INSTALLATION (parts are not to

scale):

2 ea Wall

Anchors (#9)

2 ea Ball Nuts

(#21)

3 ea Wire

Nuts (#17)

2 ea Outlet Box

Screws (#12)

1 ea Wall Plate (#7)

INSTALLATION INSTRUCTIONS:

1. Place the Wall Plate (#7) over the Outlet Box (#6), aligning the mounting slots of the Wall Plate (#7) with the mounting holes

of the Outlet Box (#6), as shown. Use a level to make sure the Wall Plate (#7) is straight. (Fig. 3)

2. Mark the location of the Keyhole Slots (#8) of the the Wall Plate (#7) onto the wall. Remove the Wall Plate (#7) from the

wall. (Fig. 3)

3. Drill a ¼” hole at the narrow end of each Keyhole Slot (#8) marking on the wall. Carefully hammer a Wall Anchor (#9) into

each Drilled Hole (#10). (Fig. 3)

4. Attach the Black Supply Wire (#13) to the Black Fixture Wire (#14) and the White Supply Wire (#15) to the White Fixture

Wire (#16) using Wire Nuts (#17). (Fig. 3) Wrap all wire connections with electrical tape for a more secure connection.

Note: If you have electrical questions, consult your local electrical code for approved grounding methods.

5. Feed the Supply Ground Wire (#19) through the Wire Hole (#20) of the Wall Plate (#7). (Fig. 3)

6. Replace the Wall Plate (#7) over the Outlet Box (#6), aligning the narrow end of each Keyhole Slot (#8) with its respective

Wall Anchor (#9). Feed the Anchor Screws (#11) through the Keyhole Slots (#8) and thread them into the Wall Anchors (#9)

until the Wall Plate (#7) is flush against the wall. Additionally, feed the Outlet Box Screws (#12) through the mounting slots

of the Wall Plate (#7) and thread them into the mounting holes of the Outlet Box (#6), as shown. Pull the power supply wires

out from the Outlet Box (#6) and through the center hole of the Wall Plate (#7). (Fig. 3)

7. Please proceed back to the Assembly Instructions.

8. Installation is complete. Turn on power at the circuit breaker or fuse box. Turn the light switch on to activate the fixture.

2 ea Anchor

Screws (#11)

8. Keyhole Slot

9. Wall Anchor

10.Drilled Hole

11.Anchor Screw

12.Outlet Box

Screw

13.Black Supply Wire

14.Black Fixture Wire

15.White Supply Wire

16.White Fixture

Wire

17.Wire Nut

20.Wire Hole

INSTALLATION:

19. Supply

Ground Wire

7. Wall Plate

6. Outlet Box

Page 7

Fig. 3

Possible Cause Corrective Action

1. Power is off. 1. Make sure power supply is on.

2. Faulty switch. 2. Test or replace switch.

1. Bulb is burned out 1. Replace light bulb.

2. Faulty wire connection. 2. Check wiring.

Fuse blows or circuit breaker

trips when light is turned on.

1. Crossed wires or power wire is grounding

out.

1. Check wire connections.

Bulb will not turn on.

Lights will not turn on.

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean

water, never a solvent) to wipe the surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the

circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly

dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the

fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft

cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a

period of five (5) years from date of purchase. This warranty applies only to the original consumer

purchaser and only to products used in normal use and service. If this product is found to be defective, the

manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of of the product at

the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse,

accident, modifications, alterations, neglect or mishandling. This warranty shall not apply to any product

that is found to have been improperly installed, set-up, or used in any way not in accordance with the

instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of

an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to

faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product,

such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not

warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a

particular purpose, other than the warranty contained herein. The manufacturer specifically

disclaims any liability and shall not be liable for any consequential or incidental loss or damage,

including but not limited to any labor/expense costs involved in the replacement or repair of said

product.

Page 8

MANUAL DE INSTRUCCIONES

LUMINARIO PARA BAÑO DE QUATRO LUCES

HOME DEPOT SKU# 108-898 (UPC# 046335943230)

Page 9

Page is loading ...

MODE D’INSTALLATION

APPLIQUE DE SALLE DE BAIN

À CUATRO LUMIÈRES

HOME DEPOT UGS N° 108-898 (CUP N° 046335943230)

Page 17

Page is loading ...

Hampton Bay HB2051-35 Installation guide

Hampton Bay HB2051-35 Installation guide

in other languages

Related papers

Other documents