Lightolier IS:6706 User manual

Type
User manual

Lightolier IS:6706 is a surface mount fixture intended for installation in accordance with the National Electrical Code and local regulations. It is suitable for ceiling installation and comes with mounting screws for easy installation. The fixture supports the use of recommended lamp wattage and type as marked on the fixture. It features a diffuser with notches that align with diffuser brackets on the ceiling pan, allowing for easy locking and unlocking of the diffuser.

Lightolier IS:6706 is a surface mount fixture intended for installation in accordance with the National Electrical Code and local regulations. It is suitable for ceiling installation and comes with mounting screws for easy installation. The fixture supports the use of recommended lamp wattage and type as marked on the fixture. It features a diffuser with notches that align with diffuser brackets on the ceiling pan, allowing for easy locking and unlocking of the diffuser.

(FIG. 2):
DIFFUSER NOTCHES pass over DIFFUSER BRACKETS.
7. To remove DIFFUSER, rotate counterclockwise until
SLOTS and secure in place by tightening MOUNTING SCREWS.
SCREWS are fully engaged in narrow portion of KEYHOLE
Green fixture wire(s) must also be connected to
grounding terminal or ground lead inside OUTLET BOX.
and connections back into OUTLET BOX.
Use WIRE NUTS (local hardware item). Push supply wires
to grounding terminal or ground lead inside OUTLET BOX.
fixture wire is a ground wire and must be connected
fixture lead to neutral (white) supply lead. Uninsulated
black fixture lead to hot (black) supply lead; white
3. While supporting CEILING PAN make electrical connections:
5. Install recommended lamp(s).
SLOTS in CEILING PAN. Slide CEILING PAN until MOUNTING
head of MOUNTING SCREWS to come through KEYHOLE
4. Position CEILING PAN over MOUNTING SCREWS and allow
SLIDE
BRACKETS
DIFFUSER
DIFFUSER
KEYHOLE SLOT
CEILING PAN
SCREWS
MOUNTING
WIRE NUTS
OUTLET BOX
FIG. 1
1. Make sure that power to OUTLET BOX is off.
OUTLET BOX.
INSTRUCTIONS FOR INSTALLATION OF DISCUS SURFACE MOUNT FIXTURES
2. Partially thread MOUNTING SCREWS supplied into
Note: This instruction sheet covers several fixture styles.
Ceiling pan, assembly, lamp type, and diffuser may vary
from that shown, although installation is the same.
locked in position.
CEILING PAN and rotate clockwise until DIFFUSER is
CEILING PAN. Gently push DIFFUSER upward against
CAUTION: USE ONLY LAMP WATTAGE AND
 TYPE MARKED ON FIXTURE.
INSTALLATION (FIG. 1):
6. Align DIFFUSER NOTCHES with DIFFUSER BRACKETS on
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local
regulations. To assure full compliance with local codes and regulations, check with your local electrical
inspectorbefore installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
Page 1 of 1A0200
WARNING: (RISK OF FIRE) SUPPLY WIRING MUST BE RATED
90˚ C. FOR CEILING INSTALLATION OF MODELS 
6700MS213N1 & 6706MS213N1 ONLY. MOST DWELLINGS
BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED FOR 60˚ C.
CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALL
IS:6706
NOTCHES
DIFFUSER
DIFFUSER
CEILING PAN
BRACKETS
DIFFUSER
OUTLET BOX
FIG. 2
UN-LOCK
LOCK
631 Airport Road, Fall River, MA 02720
LIGHTOLIER a GENLYTE THOMAS company.
  • Page 1 1

Lightolier IS:6706 User manual

Type
User manual

Lightolier IS:6706 is a surface mount fixture intended for installation in accordance with the National Electrical Code and local regulations. It is suitable for ceiling installation and comes with mounting screws for easy installation. The fixture supports the use of recommended lamp wattage and type as marked on the fixture. It features a diffuser with notches that align with diffuser brackets on the ceiling pan, allowing for easy locking and unlocking of the diffuser.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI