Lightolier IS:5543 User manual

Brand: Lightolier

Model: IS:5543

Type: User manual

Lightolier IS:5543 is a ceiling-mounted light fixture designed for indoor use. It features a diffuser ring with three auxiliary mounting holes for secure installation on various ceiling materials. The fixture supports multiple lamp types and wattages, as specified by the manufacturer. It includes a socket and lamp support clip for easy lamp installation and removal. The diffuser can be cleaned using a soft damp cloth and can be removed for thorough cleaning by releasing the retaining springs. The fixture complies with the National Electrical Code and IOCSI regulations.

READAND UNDERSTANDTHESEINSTRUCTIONSBEFOREINSTALLINGFIXTURE

INSTRUCTION SHEET NO.

sfixtureisintendedforinstallationinacmrdanmwiththeNational

Electrical Code and IOCSIregulations.

assure full mmpfiance with local @ales and regulations, deck with your Iocsl electrical inspector before

,allation.

To prevent electrical shock, turn off electrify at fuse box before proceeding.

IS:5543

Retain these instructions for maintenance reference,

1292 Page 1 of 1

INSTRUCTIONS FOR INSTALLATION

XTURE ASSEMBLY AND INSTALLATION:

1, Thread MOUNTING SCREWS intoOUTLET BOX.

2, Wtile supportingCEILING PAN make

electrical connections black fixture lead orfixlureleadwithouttracer marksto (hot)blacksupplylead;white fixturelead

or fixtureleadwithtracer mark10(neutral)whitesupplylead. Uninsulatedwire isa groundand mustbe connectedto groundhgtarminalorgroundlead inside

OUTLET BOX, Use WIF?ENUTS(localhardware

item). Push supply wires and wirenutmnnecfions backintoOUTLET BOX.

3. PositionCEILING PANover MOUNTING SCREWS andallowheadsofMOUNTING SCREWS tocomethroughtheKEYHOLE SLOTS inCEILING PAN. Secure

in place by tightening MOUNTING SCREWS,

4, Using the thrae AUXILIARY MOUNTING HOLES in CEILING PAN, secure CEILING PAN to ceiing using wood screws, toggle bolls,

oralternate fasleners (not

provided) depending on ceiling material,

5, lnstdl recommend lamps by inseiling base of lamp into SOCKET and snapping lamp into LAMP SUPPORT CLIP,

CAUTION Use lamp waftage and type as marked on fixture,

6, Align holes in

DIFFUSERRINGASSEMBLYwithMOUNTINGSTUDSonCEILINGPANandallowSTUDStopasslhroughlheholes.Secure in place bylhreadhg

KNOBS onto each MOUNTING STUDS,

)IFFUSER CLEANING AND REMOVAL:

)iffusercan be cleaned using a soft damp cloth, Should DIFFUSER need to be removed

.om diffuser ring for cleaning, follow steps below.

Whie gently pving back on one RETAINING SPRING (use a slotted screw diver)

push upon OIFFUSER allowing DIFFUSER to snap away from three RETAINING

SPRING (Ffg, 2).

!.’ Clean DIFFUSER.

1,’ Reinsfdl DIFFUSER bygeotly pushing DIFFUSER down into DIFFUSER RING until

all three RETAfNING SPRINGS engage on the edge of Ihe DIFFUSER and

DIFFUSER sits flush inside DIFFUSER RING.

NOTE: Ifsupply wires are located within three inches of

ballast, usewire rated

for at least 90° C.

WARNING-(RISK OF FIRE) MOST DWELLINGS

BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED

60” C. CONSULT A QUALIFIED ELECTRICIAN

BEFORE INSTALLATION.

DIFFu

FIG. i

1.1<5

I“ITC>I.IE la”EWH’,!W%YU

Lightolier IS:5543 User manual

Lightolier IS:5543 User manual

Lightolier IS:5543 User manual

Related papers

Other documents