Salicru SPS 1100 One User manual

SPS.ONE

UNINTERRUPTIBLE POWER SUPPLY (UPS)

USER'S MANUAL

2 SALICRU

3

General index

1. INTRODUCTION.

1.1. ACKNOWLEDGEMENT LETTER.

2. INFORMATION FOR SAFETY.

2.1. USING THIS MANUAL.

2.1.1. Conventions and used symbols.

3. QUALITY AND STANDARD GUARANTEE.

3.1. DECLARATION OF THE MANAGEMENT.

3.2. STANDARD.

3.3. ENVIRONMENT.

4. PRESENTATION.

4.1. VIEWS.

4.1.1. Equipment views.

4.1.2. Legend corresponding to the equipment views.

4.2. CONTENTS.

4.3. OPERATING PRINCIPLE.

4.3.1. Quality performances.

5. INSTALLATION .

5.1. LOCATION AND STORAGE CONDITIONS.

5.2. CONNECTING THE EQUIPMENT TO MAINS FOR FIRST

TIME OR AFTER TWO MONTHS OF NO USE.

5.3. CONNECTION OF LOADS.

5.4. CONNECTION OF MODEM/PHONE LINE.

5.5. CONNECTION OF COMMUNICATION CABLE.

5.6. DOWNLOAD AND INSTALLATION OF THE SOFTWARE.

5.7. START UP/SHUTDOWN OF THE EQUIPMENT.

5.7.1. Start up/shutdown of the SPS.ONE.

5.7.2. Shutdown of the SPS.ONE.

6. TROUBLESHOOTING GUIDE.

7. GENERAL TECHNICAL SPECIFICATIONS.

SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS)USER'S MANUAL

4 SALICRU

SALICRU

1. INTRODUCTION.

1.1. ACKNOWLEDGEMENT LETTER.

We would like to thank you in advance for the trust you have

placed in us by purchasing this product. Read this instruction

manual carefully in order to be familiar with its contents, be-

cause as much you understand and know the equipment, the

higher will be the satisfaction degree, safety level and func-

tionality optimization.

We remain at you entire disposal for any further information or

any query you should wish to make.

Yours sincerely.

• The equipment here described can cause important

physical damages due to wrong handling. This is why,

the installation, maintenance and/or fixing of the here de-

scribed equipment must be done by our staff or specifi-

cally authorised.

• Although no effort has been spared to guarantee that the

information in this manual is complete and accurate, we are

not responsible of any errors or omissions that may exist.

The images included in this document are for mere illustra-

tion and may not accurate represent the parts of the equip-

ment showed. However, the differences that may arise will

be smoothed or solved with the correct labelling on the unit.

• According to our policy of constant evolution, we reserve

the right to modify the specifications, operating or

described actions in this document without fore-

warning.

• All reproduction, copy, third party concession, modi-

fication or part or total translation of this manual or

document, in any form or medium, without the previous

written authorization of our firm, it is prohibited, reserving

of the complete and exclusive property right over itself.

5

2. INFORMATION FOR SAFETY.

2.1. USING THIS MANUAL.

The user's manual of the equipment is available in our website

for the customers, being able to be on-line readed or down-

loaded as appropiate.

Together with the own document, it is needed to have access to

the EK266*08 document as regards to «Safety instructions».

Read this manual carefully before making the erection or com-

missioning, location change, setting or any king of handling in

the equipment

The purpose of the manual is to provide the information relating

to safety and explanations over the installation and operating

procedures of the equipment. Read them carefully and follow

the stated steps in the established order.

Compliance as regards to «Safety instructions» is

mandatory, being the user the legal responsible

regarding to its observance and application.

The equipments are delivered duly labelled for the correct iden-

tification of each of its parts, and together with the instructions

of this user’s manual allowing doing any of the commissioning

and erection operations, in an easy, ordered way, without doubt.

Finally, once the equipment is installed and in operation, it is

recommended to keep the documentation in a safe and easy

access place, for future consults or doubts that could arise.

The following terms are used in the document to be referred to:

• «SPS.ONE, equipment, system, unit or UPS».- Uninter-

ruptible Power Supply SPS.ONE.

Depending on the context of the sentence, it can be re-

ferred to the UPS or to itself together with the batteries

indistinctly.

• «Batteries or accumulators».- Group or set of elements

that store the electron flow through electrochemical means.

• «S.T.S.».- Service and Technical Support.

• «client, installer, operator or user».- Both are used and

for the sense, to be referred to the fitter and/or operator,

who will make the corresponding actions, being able to fall

in that person the responsibility of making the respective

actions when acting in the name or on behalf of himself.

2.1.1. Conventions and used symbols.

Some symbols can be used and shown in the equipment, bat-

teries and/or user’s manual context.

For more information, see section 1.1.1 of EK266*08 document

relating to «Safety Instructions».

SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS)USER'S MANUAL

6 SALICRU

3. QUALITY AND STANDARD GUARANTEE.

3.1. DECLARATION OF THE MANAGEMENT.

Our target is the client’s satisfaction, therefore this Manage-

ment has decided to establish a Quality and Environmental

policy, by means of installation a Quality and Environmental

Management System that becomes us capable to comply the

requirements demanded by the standard ISO 9001 and ISO

14001 and by our Clients and concerned parts too.

Likewise, the enterprise Management is committed with the

development and improvement of the Quality and Environ-

mental Management System, through:

• The communication to all the company about the importance

of satisfaction both in the client’s requirements and in the legal

and regulations.

• The Quality and Environmental Policy diffusion and the fixa-

tion of the Quality and Environment targets.

• To carry out revisions by the Management.

• To provide the needed resources.

3.2. STANDARD.

The SPS.ONE product is designed, manufactured and com-

mercialized in accordance with the standard EN ISO 9001 of

Quality Management Systems and certified by the organism

SGS. The marking shows the conformity to the EEC Direc-

tive by means of the application of the following standards:

• 2006/95/EC of Low Voltage Safety.

• 2004/108/EC of Electromagnetic compatibility (EMC).

According with the harmonised norms and certified by an ex-

ternal laboratory. The reference norms are:

• EN-IEC 62040-1. Uninterruptible power supply (UPS). Part

1-1: General and safety requirements for UPS’s used in ac-

cessible areas by end-users.

• EN-IEC 60950-1. IT equipments. Safety. Part 1: General

requirements.

• EN-IEC 62040-2. Uninterruptible power supply (UPS). Part

2: EMC requirements.

The manufacturers responsibility is excluded in the

event of any modification or intervention in the product

by the customer’s side.

This is a product for both professionals and home work-

stations use.

Declaration of conformity CE of the product is at the

client disposal under previous request to our headquar-

ters offices.

3.3. ENVIRONMENT.

This product has been designed to respect the environment

and has been manufactured in accordance with the standard

ISO 14001.

Equipment recycling at the end of its useful life:

Our company commits to use the services of authorised so-

cieties and according to the regulations, in order to treat the

recovered product at the end of its useful life (contact your dis-

tributor).

Packaging:

To recycle the packaging, follow the legal regulations in force,

depending on the particular standard of the country where the

equipment is installed.

Batteries:

The batteries mean a serious danger for health and environ-

ment. The disposal of them must be done in accordance with

the standards in force.

7

4. PRESENTATION.

4.1. VIEWS.

4.1.1. Equipment views.

Figures 1 and 5 show the illustrations of the equipments ac-

cording to the model. Nevertheless and as the product is in

constant evolution, some discrepancies or small contradictions

can arise. So, if any questions, the labels in the own equipment

will prevail.

Any values as regards to features or specifications can

be checked in the nameplate. Act in your installation

accordingly.

9

10

11

12

9

10

11

12

9

10

13

14

15

16

17

SPS.500.ONE, SPS.700.ONE

and SPS.900.ONE

SPS.1100.ONE SPS.1500.ONE

and SPS.2000.ONE

Fig. 1. SPS.ONE front views.

4

5

6

3

1

7

3

1

8

7

5

6

3

2

7

4

3

SPS.500.ONE, SPS.700.ONE

and SPS.900.ONE

SPS.1100.ONE SPS.1500.ONE

and SPS.2000.ONE

Fig. 2. Rear views with schuko outlets.

SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS)USER'S MANUAL

8 SALICRU

4

5

6

3

1

3

1

8

2

7

5

6

3

4

3

SPS.500.ONE, SPS.700.ONE

and SPS.900.ONE

SPS.1100.ONE SPS.1500.ONE

and SPS.2000.ONE

Fig. 3. Rear views with UK outlets.

4

5

6

3

1

7

3

1

8

7

5

6

3

2

7

4

3

SPS.500.ONE, SPS.700.ONE

and SPS.900.ONE

SPS.1100.ONE SPS.1500.ONE

and SPS.2000.ONE

Fig. 4. Rear views with French outlets.

4

5

6

3

2

7

8

5

6

2

7

2

7

3

4

3

SPS.500.ONE, SPS.700.ONE

and SPS.900.ONE

SPS.1100.ONE SPS.1500.ONE

and SPS.2000.ONE

Fig. 5. Rear views with IEC outlets.

9

4.1.2. Legend corresponding to the equipment views.

1. Input power cord with power plug in its end.

2. IEC inlet to supply the equipment (models with no

power cord 1 only).

3. Outlets.

4. USB communication port.

5. RJ input connector, to protect the overvoltages in the

modem or telephone lines.

6. RJ output connector, for modem or telephone lines.

7. Input protection, depending on the model by means of

thermal switch or fuse.

8. Fan of the equipment (SPS.1500.ONE and SPS.2000.

ONE models only).

9. ON/OFF button of the equipment.

10. Red colour led ON. Equipment in fault mode. Also if this

led is blinking with the same modulation as the acoustic

alarm, it warns that the equipment is reaching the end of

back up time.

11. Green colour led ON. Equipment in AC mode - output

power supply comes from input mains-.

12. Yellow colour led blinking. Equipment in Battery mode

-the output comes from the internal battery-.

13-16. Green colour led ON. Depending on the status of led 17

means:

With led 17 ON -Equipment in AC mode-, it shows the

load level connected at the output from 0 to 25%, from

26 to 50, from 51 to 75 % and from 76 to 100 % respec-

tively.

With the led 17 blinking -Equipment in Battery mode-, it

shows the battery capacity level from 0 to 25%, from 26

to 50, from 51 to 75 % and from 76 to 100 % respectively.

17. Green colour led, which shows that the status of the

equipment depending if it is ON or blinking:

ON, equipment in AC mode -output power supply comes

from the input mains-.

Blinking, equipment in Battery mode -output power

supply comes from the internal battery-.

4.2. CONTENTS.

Inside the packaging of the equipment is supplied:

• SPS.ONE equipment.

• Quick guide.

• USB communication cable.

• Power cord (models with IEC input connector 2 only).

4.3. OPERATING PRINCIPLE.

• Basically, it is an Uninterruptible Power Supply (UPS) with

Line-interactive technology, which gives the best protection

solution for the IT equipments or their environments for

both home and professional use (small business, offices,

shops,…).

• The use of the Boost&Buck AVR technology -permanent

stabilization of the power supply-, gives a double advan-

tage, a better care of the connected loads and a less use of

the UPS batteries.

• In case of input mains fault, thanks to the batteries it sup-

plies electrical power to keep the loads ON.

• In order to complete the offered safety, it also has a data

line protection to protect it from any transient voltage in

that line.

• The communication through the USB port between the UPS

and the IT system (communication cable included) and the

monitoring software which runs under Windows, Linux,

Unix and Mac have to be highlighted.

4.3.1. Quality performances.

• Line-interactive technology.

• Control by microprocessor, which guarantees a high reli-

ability.

• Boost&Buck AVR permanent stabilization.

• USB interface in any model of the series.

• Monitoring software for Windows, Linux, Unix and Mac.

• Data / phone / internet line protection.

• One ON/OFF button to make more friendly and easier its

use.

• Protection against overloads, short-circuits and transients.

• Intelligent battery charger, which makes shorter the av-

erage recharging time.

• Battery recharging with the equipment OFF.

• Cold-start function, UPS can be started up through the bat-

teries.

• Automatic restart up when input mains is restored.

SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS)USER'S MANUAL

10 SALICRU

5. INSTALLATION .

• Read and respect the Safety Information, described

in section 2 of this document. To obviate some of

the indications stated in it, can cause a serious or very se-

rious injuries to persons in direct contact or in the vicinity,

as well as breakdowns in the equipment and/or loads con-

nected to itself.

• Check that all data of the nameplate are the required ones

by the installation.

• Once the equipment is unpacked and before proceeding, in-

spect and check it in order to see that everything is the right

conditions. Otherwise contact with the dealer.

• Depending on the morphology and sector or oper-

ating environment, there could be some connection

and use restrictions of the equipment:

 Due to its connection.

– Equipments with power cord with plug and outlets

(not hard-wired).

It can be connected by personnel with no specific

training, so in general the same end-user in home

environments can do it.

 Due to its use.

– Equipments with no terminal strip, in general the

ones destined for home environments and in a

lesser extent in shops and industrial or other sec-

tors.

Personnel with no specific training can use

them, just with the simple help of the user's

manual.

• Any connection of the equipment including the com-

munication one (interface), will be done with all the

switches turned off and with no voltage present (power

supply switch of the UPS to «Off»).

• Do not forget that the UPS is an energy generator, so

the end-user has to take the necessary precautions

against direct or indirect contacts.

5.1. LOCATION AND STORAGE CONDITIONS.

• Install the UPS in a protected area ad free of excessive hu-

midity and with a suitable ventilation.

• Locate the UPS 20cm far from other units in order to avoid

interferences.

• Do not start up the equipment where the temperature and

humidity exceed the allowed limits(see the technical speci-

fications).

20 cm 20 cm

5.2. CONNECTING THE EQUIPMENT TO MAINS FOR

FIRST TIME OR AFTER TWO MONTHS OF NO USE.

• Plug in mains power plug 1 to an AC outlet.

In those models with IEC inlet , a cable is supplied together

with the equipment. Insert the IEC connector into its base 2

and the mains power plug of the other end to the AC outlet.

• To get better results, charge the batteries

for 4 hours at least, before using it for

first time or after a period of time longer

than two months of no use.

Otherwise, the reaction of the SPS.ONE

can be unsatisfactory in case of black-

outs during the first hours of operation.

Becuase its capacity of response during

unexpected blackouts of the AC mains is

conditioned to the stored energy in the

batteries.

• The battery is charged by plugging the equipment to mains

only.

5.3. CONNECTION OF LOADS.

• Plug the loads in the outlets 3, located in the rear side of

the unit.

• Do not connect a laser printer or

scanner to the UPS. They can

damage the unit and/or deplete the en-

ergy stored in the batteries, which is re-

served for a more critical and sensitive

loads.

5.4. CONNECTION OF MODEM/PHONE LINE.

Connect the modem/phone line to the RJ 5 connector at the

back of the UPS. Connect the modem/phone cable to the RJ 6

connector of the equipment.

5.5. CONNECTION OF COMMUNICATION CABLE.

• To make possible unattended UPS start up and shutdown

and the monitoring of its status, connect one of the ends of

the communication cable to connector 4 of the USB port of

the SPS.ONE and the other end to the communication port

of the PC.

11

• With the monitoring software installed in the PC, the UPS

start up / shutdown can be set, as well as to follow up

its status. Follow the next steps before downloading and

installing the monitoring software:

5.6. DOWNLOAD AND INSTALLATION OF THE

SOFTWARE.

• The monitoring software downloading is free provided that

the user is log in and the equipment too in the site:

support.salicru.com

• In the same log in, in the initial page there is a shortcut to

«ACTIVATION GUIDE». Follow the stated steps.

• Once the log in is done, the software of the related equip-

ment can be downloaded through the site :

support.salicru.com/software

• For its installation proceed as any other software.

• When the PC is started up, the monitoring software will be

show as an orange icon in the system tray, near the clock.

5.7. START UP/SHUTDOWN OF THE EQUIPMENT.

5.7.1. Start up/shutdown of the SPS.ONE.

• With the SPS.ONE completely shutdown, press the button

9 to start up the equipment.

• When starting up the equipment, an internal autotest is

done, so all the leds light. This process takes some sec-

onds, after that, the UPS supplies output voltage coming

from mains or the batteries.

Regardless of the start up is done with mains or over the

batteries (no mains), the autotest will be done.

• Start up the loads.

5.7.2. Shutdown of the SPS.ONE.

• Shutdown the loads.

• Shutdown the equipment by pressing the button 9.

SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS)USER'S MANUAL

12 SALICRU

6. TROUBLESHOOTING GUIDE.

Use the following table to solve the minor problems that can

be found:

Problem Possible cause Solutions

No LED is ON in

the front panel.

Low battery.

Charge the UPS for 6 hours

at least.

Battery fault.

Replace the battery by another

of the same type.

UPS is not ON.

Press the UPS start up button

again.

Acoustic

alarm beeps

permanently

with AC mains

correct.

UPS is overloaded.

Disconnect some loads first.

Before start the unit up

again, check that the load is

connected according to the

power specifications of the

unit.

Short back up

time in case of

blackout.

UPS is overloaded. Disconnect some critical loads.

Battery voltage is

too low.

Charge the UPS for 6 hours

at least.

Faulty battery, due

to a high ambient

temperature or

wrong operation.

Replace the battery by another

of the same type.

Mains is

correct, but the

equipment is in

battery mode.

Main power plug is

not well connected.

Reconnect the main power

plug to mains suitably.

Table 1. Troubleshoowting guide table.

• If you are log in the site:

support.salicru.com

, you will have access to:

support.salicru.com/troubleshooting

, to consult an extended troubleshooting guide of the equip-

ment, a part from other services that there will be available

for the mere fact of being only logged.

13

7. GENERAL TECHNICAL SPECIFICATIONS.

MODEL 500 700 900 1100 1500 2000

Power(VA) 500 700 900 1100 1500 2000

Power (W) 250 360 480 600 900 1200

Technology Line-interactive

INPUT

Voltage 220 / 230 / 240 V AC.

Range 162-290 V AC.

Nominal frequency 50 / 60 Hz.

Frequency

autosensing

Yes.

Stabilization Buck/Boost AVR.

OUTPUT

Voltage (V AC) 220 / 230 / 240 V AC.

Voltage accuracy

(1)

± 10 %.

Frequency

(1)

50 / 60 ± 1 Hz.

Wave shape

(1)

Simulated sinewave

Available outlets Schuko (DIN), French (FR), UK, IEC.

Transfer time 2-6 ms typical, 10 ms maximum.

PROTECTION

Input

Rearmable thermal or fuse (depending on the

model).

Complete protection

Overload, battery discharge and charger

overcurrent.

Data line Tel./Fax, modem, ADSL internet.

BATTERY

Type

Pb-Ca sealed maintenance free, 3-5 years design

lifetime.

Charge time 4-6 hours to recharge the 90% of the capacity.

Battery

replacement

warning

Yes.

User hot swap Yes.

Capacity (Ah) 4,5 7 9 7 9 9

Number 1 2 2 2

FUNCTIONS

ColdStart Yes.

Autotest In each start up.

Automatic Restart

up

Yes, after the end of autonomy and mains is

restored.

VISUAL INDICATIONS

AC mode led Green colour, ON.

Battery mode led

Modo Batería

Yellow colour, blinking.

Fault led / End of

autonomy

Red colour, ON.

Battery charge

level bar

- Green colour.

Connected load

level bar

- Green colour.

MODEL 500 700 900 1100 1500 2000

ACOUSTIC ALARM

Battery mode Modulated every 10 sec..

Low battery Modulated every 1 sec..

Overload Modulated every 0,5 sec..

Battery

replacement

Modulated every 2 sec..

Fault Continuous.

COMMUNICATION

Port USB 2.0.

Software Ready for Windows, Linux, Unix and Mac.

Download from support.salicru.com

GENERALS

Maximum altitude 2400 m. a.s.l..

Relative humidity Up to 90 % non-condensing.

Temperature 0.. 40 ºC.

Acoustic noise at

1 m.

< 40 dB.

STANDARDS

Safety EN-IEC 62040-1, EN-IEC 60950-1.

Electromagnetic

compatibility. (EMC)

EN-IEC 62040-2.

Quality and

Environmental

management

ISO 9001 and ISO 14001.

DIMENSIONS AND WEIGHT

Depth (mm) 287 350 397

Width (mm) 100 146 146

Height (mm) 142 160 205

Net weight (Kg) 3,55 4,25 4,9 8,0 11,1 11,5

(1)

Battery mode.

Table 2. General technical specifications.

SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS)USER'S MANUAL

14 SALICRU

: .............................................................................................................................................................................................................

.........................................................................................................................................................................................................................

15

: .............................................................................................................................................................................................................

.........................................................................................................................................................................................................................