luminii LETO 44 Mini P Installation guide

luminii
Brand
luminii
Model
LETO 44 Mini P
Type
Installation guide

The luminii LETO 44 Mini P is a versatile lighting fixture suitable for dry indoor locations, offering both AC and DC power options. It features a single feed cable for pendant mounting, allowing for easy installation and adjustment of the cable length to achieve the desired height. With its sleek design and magnetic trim plate, the LETO 44 Mini P provides a modern and customizable lighting solution for various applications.

The luminii LETO 44 Mini P is a versatile lighting fixture suitable for dry indoor locations, offering both AC and DC power options. It features a single feed cable for pendant mounting, allowing for easy installation and adjustment of the cable length to achieve the desired height. With its sleek design and magnetic trim plate, the LETO 44 Mini P provides a modern and customizable lighting solution for various applications.

LETO 44 Mini P
1 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Read and follow these
instructions before installing or
maintaining this product
Veuillez lire et suivre ces
instructions avant l’installation ou
l’entretien de ce produit
• This product is suitable for DRY INDOOR
LOCATIONS ONLY
• Make sure this product is NOT on the same
circuit as inductive loads, (e.g. fluorescent bulbs,
discharge bulbs, ventilation fans, etc...)
• Do not switch on line voltage until all wiring is
complete
• Incorrect wiring will result in irreparable damage
to LED and power supply
• This product should only be installed by a
licensed electrician
• Ce produit convient pour une installation DANS
UN ENDROIT SEC SEULEMENT
• Assurer vous que des charges inductives ne se
retrouvent pas sur le même circuit que ce produit,
(i.e. fluorescent, ampoules à décharge,
ventilateurs, etc...)
• Compléter les branchements avant de mettre
sous tension
• Un branchement incorrect créerait des
dommages irréparables à l’alimentation et au DEL
• Ce produit devrait être uniquement installé par un
électricien qualifié
Warranty
Garantie
• This product must be installed in accordance
with all applicable installation codes and
ordinance
• Limited five (5) years warranty
• Warranty is void in the eventuality of
unauthorized modifications and/or improper use
• Ce produit doit être installé conformément au
code d’installation et autres normes applicables
• Garantie limitée de cinq (5) ans
• La garantie est non valide advenant une
modification non autorisée ou un usage non
approprié
Powered Aircraft
AC P4 / DC P5
For powered aircraft height
adjustment, see P6
Feed Suspended
AC P2 / DC P3
954 SEMI-RECESSED CANOPY
Overview / Vue d’ensemble
LETO 44 Mini P
2 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Turn screws until housing is secured in place
(arms will rotate and clamp down on ceiling)
9-25mm
Pendant: Single Feed Cable (AC Connection)
Finish ceiling installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose the driver.
2
Make electrical connections and use appropriate
strain relief.
3
Reassemble housing and insert into ceiling. Push
aside to leave room for canopy.
Unscrew gripper plate and separate from canopy.
7
Connect dimming controls to included cable
clamps. Insert wires and canopy into ceiling.
5
Loosen set screw and adjust cable to desired
height. Cut and reconnect wire if needed.
8
Re-attach gripper to canopy and slide trim plate
up until held in place by magnets.
9
1
4 6
LETO 44 Mini P
3 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Pendant: Single Feed Cable (Remote DC Connection)
1
Finish ceiling installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose fixture
wiring. Cylinder housing is used as DC junction
box.
2
Make electrical connections and use appropriate
strain relief.
3
4
Reassemble housing and insert into ceiling. Push
aside to leave room for canopy.
Unscrew gripper plate and separate from canopy.
7
Insert canopy into ceiling.
5
Loosen set screw and adjust cable to desired
height. Cut and reconnect wire if needed.
8
Re-attach gripper to canopy and slide trim plate
up until held in place by magnets.
9
6
Turn screws until housing is secured in place
(arms will extend and clamp down on ceiling)
9-25mm
LETO 44 Mini P
4 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
6
Turn screws until housing is secured in place
(arms will extend and clamp down on ceiling)
9-25mm
Pendant: Powered Aircraft Cable (AC Connection)
1
Finish ceiling installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose the driver.
2
Make electrical connections and use appropriate
strain relief.
3
4
Reassemble housing and insert into ceiling. Push
aside to leave room for canopy.
Connect dimming controls to included cable
clamps. Insert wires and canopy into ceiling.
5
Slide trim plate up until held in place by magnets.
7
LETO 44 Mini P
5 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Pendant: Powered Aircraft Cable (Remote DC Connection)
1
Finish ceiling installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose fixture
wiring. Cylinder housing is used as DC junction
box.
2
Make electrical connections and use appropriate
strain relief.
3
4
Reassemble housing and insert into ceiling. Push
aside to leave room for canopy.
Insert canopy into ceiling.
5
Slide trim plate up until held in place by magnets.
7
6
Turn screws until housing is secured in place
(arms will extend and clamp down on ceiling)
9-25mm
LETO 44 Mini P
6 Rev July 26, 2021 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Unscrew gripper plate separate from canopy.
2
Loosen set screw and adjust cable to desired
height.
3
If cables develop a twist, loosen set screw and
cycle cable through the gripper 4-5 times.
5
Cut excess cable leaving ~3” above gripper.
Make electrical connections using appropriate
hardware.
4
Tighten screws, re-attach gripper plate to canopy
and slide trim plate up until held in place by
magnets.
6
Remove trim plate from the canopy
1
Height Adjustment: Powered Aircraft Cable
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

luminii LETO 44 Mini P Installation guide

luminii
Brand
luminii
Model
LETO 44 Mini P
Type
Installation guide

The luminii LETO 44 Mini P is a versatile lighting fixture suitable for dry indoor locations, offering both AC and DC power options. It features a single feed cable for pendant mounting, allowing for easy installation and adjustment of the cable length to achieve the desired height. With its sleek design and magnetic trim plate, the LETO 44 Mini P provides a modern and customizable lighting solution for various applications.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents