Sunco Lighting ‎SHG-40W-2PK 4FT LED Grow Light for Indoor Plants 40W Installation guide

‎SHG-40W-2PK 4FT LED Grow Light for Indoor Plants 40W
Sunco Lighting
Brand
Sunco Lighting
Model
‎SHG-40W-2PK 4FT LED Grow Light for Indoor Plants 40W
Type
Installation guide
The Brighter Choice.
40W GROW LIGHT
Install Guide and Manual
COMPONENTS
EASY INSTALLATION
1.
2.
4.
7.
3.
5.
6.
9.
8.
Turn off circuit breaker that provides power to
the light switch.
Mounting surface must be able to support the
weight of the fixture.
Depending on your lighting plan, space any
additional anchors accordingly.
• Link up to 4 shop lights together
Insert the “V” hook ends into the slots in
the light fixture end cap. Repeat steps on
the opposite side.
Hang the loose ends of the chain onto the
Screw Eye hooks in the ceiling.
Drill pilot holes 46.75 inches apart. Insert two
plastic anchors, then screw each eye hook into
an anchor.
Install a “V” hook into one end of the chain link
provided. Loop one S Hook onto the other end of
the chain.
• Repeat with second chain.
Use pliers to crimp ends and secure as needed.
Plug the power cord into an electrical outlet.
Turn on the circuit breaker and test the light.
• Distance between lamp and plant surface
should be between 12 - 39 inches.
Suspension Install Required Tools: Drill, Ladder, Hammer,
Pliers, Tape Measure, Pencil.
To install on plaster board:
• Minimum 3/8 inch thickness required
• Minimum #8 eye hook screws with plastic anchors,
or expansion bolts (not included)
Turn Power OFF
Connect to
additional
shop light(s)
Connect to
Power Outlet
46.75” apart
12”- 39”
WARNING SPECIFICATIONS
Voltage
Wattage
Damp
Steel+PC
2.70lbs
5 years
120V
40W
Housing
Weight
Warranty
Suitable for Locations Ingress
All electrical connections must be in accordance with local and National Electric Code
(N.E.C.) standards. Consult a qualified electrician if you are unfamiliar with proper elec-
trical wiring connections. Please review
instructions carefully before proceeding.
WARNING: Risk of fire or electric shock. Do not alter, relocate or remove wiring during
installation.
This fixture complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
NOTE: Not for use with dimmers. Do not install directly over a heat source.
Chain Link “S” Hook Screw Eye Hook Plastic Anchor Screw
X4X6X2X4X2
Front
Side
The Brighter Choice.
40W GROW LIGHT
Install Guide and Manual
EASY INSTALLATION
1.
2.
4.
6.
3.
5.
8.
7.
Turn off circuit breaker that provides power to
the light switch.
Mounting surface must be able to support the
weight of the fixture.
• Plaster board should be 3/8 inch thick.
Depending on your lighting plan, space any
additional anchors accordingly.
• Link up to 4 shop lights together
Distance from the lamp to the plant surface
should be 12-39 inches.
Install four plastic anchors 46.25 inches apart
and 4.4 inches apart. Insert a screw into each
anchor.
• Gap between cap nut and ceiling
should be 0.33 inches.
Lift fixture up to screws and slide to one side to
secure into place. Fixture should be firmly fixed
against screws.
Plug the power cord into an electrical outlet.
Turn on circuit breaker and test light.
Turn Power OFF
Turn Power ON
46.25”
4.4”
0.33”
0.14”
Connect to
additional
shoplight(s)
Connect to
Power Outlet
12”- 39”
Direct Mount Installation Required Tools: Drill, Ladder, Hammer,
Pliers, Tape Measure, Pencil.
WARNING
LIGHT DISTRIBUTIONCOMPONENTS
All electrical connections must be in accordance with local and National
Electric Code (N.E.C.) standards. Consult a qualified electrician if you are
unfamiliar with proper electrical wiring connections. Please review instructions
carefully before proceeding.
WARNING: Risk of fire or electric shock. Do not alter, relocate or remove wiring
during installation.
This fixture complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: Not for use with dimmers. Do not install directly over a heat source.
Chain Link “S” Hook Screw Eye Hook Plastic Anchor Screw
X4X6X2X4X2
  • Page 1 1
  • Page 2 2

Sunco Lighting ‎SHG-40W-2PK 4FT LED Grow Light for Indoor Plants 40W Installation guide

‎SHG-40W-2PK 4FT LED Grow Light for Indoor Plants 40W
Sunco Lighting
Brand
Sunco Lighting
Model
‎SHG-40W-2PK 4FT LED Grow Light for Indoor Plants 40W
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents