1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove collar loop (D) from chain (H) by removing quick link (E).
3. Install mounting plate (B) to the junction box and secure with
mounting screws (C).
4. Secure collar loop (D) to mounting plate (B) using pliers to tighten
locknut.
5. Install canopy (F) to collar loop (D) and secure with collar ring (G).
6. Determine desired overall length, and amount of chain (H) needed.
Shorten chain using chain pliers. (Keep extra chain)
7. Remove hex nut (U) and spring washer (V) from rod (Q), then thread
rod (Q) to cluster (R).
NOTE: It is recommended to have a helper assist in supporting the
fixture for steps 8-10.
8. Feed fixture wire and ground wire through bottom hole of spider on
shade (J), then install shade (J) to rod (Q) securing with spring
washer (V) and hex nut (U).
9. Thread fixture loop (I) to the threaded nipple.
10. Attach chain (H) to collar loop (D) and fixture loop (I) using quick
links (E). Secure quick links (E).
Antigua Medium Drum Chandelier
Item # CHC 5016
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Chain Pliers
Slip Joint Pliers Measuring Tape Wire Cutters
Wire Strippers
NOTICE:
US
M
L
I
D
S
E
T
LED
C
B
D
E
I
J
K
L
N
M
P
Q
R
M
F
G
H
A
V
U
Bulbs not included
Diagram 1
Diagram 2
Diagram 3
Y
S
T
Y
X
K
L PERSONS REQUIRED: Two
K (25 pcs)
L (12 pcs)
Antigua Medium Drum Chandelier
Item # CHC 5016
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
11. Thread fixture wire and ground wire through chain (H).
NOTE: When you reach the collar loop (D), ensure there is no tension
on the wires. Cut excess wires, being sure to leave enough to reach
the junction box.
12. Separate two sides of molded wire, and strip insulation on each 5/8".
13. Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully.
14. Twist all fixture wires together, and slip through center hole of collar
loop (D).
NOTE: Untwist wires and separate to prepare for connection.
15. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (A).
NOTE: It is imperative that the fixture is grounded.
16. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually
white) using wire nut (A).
17. Connect fixture hot wire (smooth with markings) to the supply hot
wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
18. Make sure all wire connections are tight, then carefully tuck into the
junction box.
19. Install canopy (F) to collar loop (D) and secure with collar ring (G).
NOTE: It is recommended to have a helper assist in supporting the
fixture for steps 20.
NOTICE:
US
M
L
I
D
S
E
T
LED
C
B
D
E
I
J
K
L
N
M
P
Q
R
M
F
G
H
A
V
U
Bulbs not included
Diagram 1
Diagram 2
Diagram 3
Y
S
T
Y
X
K
L
K (25 pcs)
L (12 pcs)
Antigua Medium Drum Chandelier
Item # CHC 5016
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
20. Install shade (M) to shade (J), securing with hanging rods (L) and
locking pins (K). Repeat for shades (N , M & P). See diagram 2.
21. Install light bulbs into the sockets.
22. Thread finial (Y) to threaded nipple on bottom of cluster (R).
Diffuser Option:
23. Thread rod (S) to threaded nipple on bottom of cluster (R).
24. Attach rubber washer (T) to either side of diffuser (X), then install to
rod (S) and secure with finial (Y). See diagram 3.
NOTE: Do not overtighten otherwise glass could become damaged.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
Not use abrasive or chemical agents.
NOTICE:
US
M
L
I
D
S
E
T
LED
C
B
D
E
I
J
K
L
N
M
P
Q
R
M
F
G
H
A
V
U
Bulbs not included
Diagram 1
Diagram 2
Diagram 3
Y
S
T
Y
X
K
L
K (25 pcs)
L (12 pcs)
Antigua Medium Drum Chandelier
Item # CHC 5016
UNPACKING NOTICE
Please follow instructions below to avoid possible damages caused by
improper removal.
NOTICE:
US
M
L
I
D
S
E
T
LED
1. Open box and remove top layer of packaging.
2. Evenly lift shade in areas indicated by arrows (see diagram) until
clear of packaging. Place on clean, soft surface.
NOTE: Remove slowly to avoid damages.
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
VISUAL COMFORT CHC5017AB-NAB User manual
-
-
-
-
-
-
-
-
-
Other documents
-
urban ambiance UHP2783 Installation guide
-
Savoy House 3-1773-6-320 User manual
-
Currey and Company 9492 Installation guide
-
Ralph Lauren RL5790 Ancram Large Empire Chandelier Operating instructions
-
YOUKAIN HDLP-51114 User manual
-
-
-
Visual Comfort Studio CHC 1474GI-NP Installation guide
-
circa LIGHTING PB 5045 User manual
-
