VISUAL COMFORT CHC 1141 User manual

Type
User manual

VISUAL COMFORT CHC 1141 is a stunning chandelier that can elevate the ambiance of any room with its elegant design and warm, inviting light. This fixture features multiple arms with sockets for light bulbs, allowing you to customize the brightness and mood of your space. Installation requires basic tools and electrical knowledge, but the detailed instructions provided guide you through each step, ensuring a safe and successful setup. With its timeless design and high-quality construction, VISUAL COMFORT CHC 1141 promises years of beautiful illumination.

VISUAL COMFORT CHC 1141 is a stunning chandelier that can elevate the ambiance of any room with its elegant design and warm, inviting light. This fixture features multiple arms with sockets for light bulbs, allowing you to customize the brightness and mood of your space. Installation requires basic tools and electrical knowledge, but the detailed instructions provided guide you through each step, ensuring a safe and successful setup. With its timeless design and high-quality construction, VISUAL COMFORT CHC 1141 promises years of beautiful illumination.

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove collar loop (D) from chain (G) by removing quick link (V).
3. Install mounting plate (B) to the junction box and secure with
mounting screws (C).
4. Secure collar loop (D) to mounting plate (B) using pliers to tighten
locknut.
5. Install canopy (E) to collar loop (D) and secure with collar ring (F).
6. Determine desired overall length, and amount of chain (G) needed.
Shorten chain using chain pliers. (Keep extra chain)
7. Attach chain (G) to collar loop (D) and fixture loop (W) using quick
links (V). Secure quick links (V).
8. Install fixture arms (U) to center plate (Y) and secure with
washers (J) and lock nuts (K). (See diagram 1)
NOTE: Check that the arms are spaced evenly before final tightening.
9. Connect all neutral wires (ribbed) from three (3) of the fixture arms (U)
with jumper wire (ribbed) and fixture neutral wire (ribbed), then secure
with wire nut (I). Repeat with remaining three (3) wires on opposite
side of fixture. See diagram 2.
10. Connect all hot wires (smooth with markings) from three (3) of the
fixture arms (U) with jumper wire (smooth with markings) and fixture
hot wire (smooth with markings), then secure with wire nut (I).
Repeat with remaining three (3) wires on opposite side of fixture.
See diagram 2.
Bernardo Large Chandelier
Item # CHC 1141
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Chain Pliers
Slip Joint Pliers Measuring Tape Wire Cutters
Wire Strippers
NOTICE:
E
F
V
V
C
G
W
D
B
A
H
Diagram 3
Bulbs not included
US
M
L
I
D
S
E
T
J
K
SI
Y
N
L
O
N
M
Q
R
U
X
J
K
Y
Diagram 1
Diagram 2
Arm
neutral wires
Fixture neutral wire
Jumper
hot wire
Arm
hot wires
Jumper
neutral wire
Fixture hot wire
Bernardo Large Chandelier
Item # CHC 1141
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
11. Install metal bowl (L) to threaded nipple (S) and secure with metal
ring (M).
12. Attach rubber washers (N) to either side of glass bowl (O) and install
to threaded nipple (S) and secure with finial (Q).
13. Thread fixture wire and ground wire through chain (G).
NOTE: When you reach the collar loop (D), ensure there is no tension
on the wires. Cut excess wires, being sure to leave enough to reach
the junction box.
14. Separate two sides of molded wire, and strip insulation on each 5/8".
15. Loosen collar ring (F) and let canopy (E) slip down chain (G) carefully.
16. Twist all fixture wires together. Slip through center hole of collar
loop (D).
NOTE: Untwist wires and separate to prepare for connection.
17. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 3). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (A).
NOTE: It is imperative that the fixture is grounded.
18. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually
white) using wire nut (A).
19. Connect fixture hot wire (smooth with markings) to the supply hot
wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
20. Make sure all wire connections are tight, then carefully tuck into the
junction box.
NOTICE:
E
F
V
V
C
G
W
D
B
A
H
Diagram 3
Bulbs not included
US
M
L
I
D
S
E
T
J
K
SI
Y
N
L
O
N
M
Q
R
U
X
J
K
Y
Diagram 1
Diagram 2
Arm
neutral wires
Fixture neutral wire
Jumper
hot wire
Arm
hot wires
Jumper
neutral wire
Fixture hot wire
Bernardo Large Chandelier
Item # CHC 1141
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
21. Install canopy (E) to collar loop (D) and secure with collar ring (F).
22. Place discs (R) and tubes (X) onto arms (U).
23. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
Not use abrasive or chemical agents.
NOTICE:
E
F
V
V
C
G
W
D
B
A
H
Diagram 3
Bulbs not included
US
M
L
I
D
S
E
T
J
K
SI
Y
N
L
O
N
M
Q
R
U
X
J
K
Y
Diagram 1
Diagram 2
Arm
neutral wires
Fixture neutral wire
Jumper
hot wire
Arm
hot wires
Jumper
neutral wire
Fixture hot wire
  • Page 1 1
  • Page 2 2
  • Page 3 3

VISUAL COMFORT CHC 1141 User manual

Type
User manual

VISUAL COMFORT CHC 1141 is a stunning chandelier that can elevate the ambiance of any room with its elegant design and warm, inviting light. This fixture features multiple arms with sockets for light bulbs, allowing you to customize the brightness and mood of your space. Installation requires basic tools and electrical knowledge, but the detailed instructions provided guide you through each step, ensuring a safe and successful setup. With its timeless design and high-quality construction, VISUAL COMFORT CHC 1141 promises years of beautiful illumination.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI