Vivitek D8800 User manual

Brand: Vivitek

Model: D8800

Category: Data projectors

Type: User manual

User’s Manual

D8800 Series

Contents

yCopyright 4

yDisclaimer 4

yAbout this manual 4

IMPORTANT SAFETY INSTRUCTIONS 5

yDisposal of old electrical and electronic equipment 6

yImportant Recycle Instructions: 6

INTRODUCTION 7

yAbout This Manual 7

yDescription, Features and Benefits 7

yParts List 8

CONTROLS AND FUNCTIONS 9

yD8800/D8900/D8010W at a Glance 9

yI/O Panel 10

yKEYPAD 11

yRemote control 12

yTo install batteries in the remote control 13

yRange of effective remote control signal reception 13

Installation Considerations 14

yAmbient Light 14

yThrow Distance 14

yModes of installation 15

yAllow at least 50 cm clearance around the exhaust vent. 16

Lens Shift 17

yVertical Lens Shift 17

yHorizontal Lens Shift 17

Connecting the projector to other devices. 18

yHDMI Connection 18

yTrigger connection 18

yIR Input connection 19

yS-VIDEO, VIDEO connection 19

yCOMPONENT connection 20

yRS-232 Connection 20

yLAN Connection 21

Start using the projector - Adjustments 22

yConnecting to AC Power 22

yTurning on the Power 22

yChanging the OSD Language 23

yAdjusting the Picture Orientation 23

yLens Adjustments 24

Start using the projector - Operation 25

ySelecting An Input Source 25

ySelecting an Aspect Ratio 25

yUsing the OSD 25

Start using the projector - OSD Introduction 26

yOSD Menu Tree 26

yOSD Introduction - INPUT 28

yOSD Introduction - PICTURE 31

yOSD Introduction - LAMPS 34

yOSD Introduction - ALIGNMENT 35

yOSD Introduction - CONTROL 39

yOSD Introduction - SERVICE 45

Change Lamp 47

yTo replace the projector lamp1 47

yTo replace the projector lamp2 48

Change Lens 49

yTo replace the projector Lens 49

Change Filter 51

yTo replace the Filter on the left side of the projector 51

yTo replace the Filter on the right side of the projector 52

LED Status 53

yPower LED 53

yStatus LED 53

yLamp1/Lamp2 LED 53

yTemp LED 53

yShutter LED 53

SPECIFICATIONS 54

SERIAL INTERFACE SPECIFICATIONS 55

yTransfer Specifications 55

yRS-232 Commands 55

yIR Codes and Key names 55

yOperations Commands 56

Dimensions 62

Supported Timings 63

Projection Distance and Screen Size 64

yD8800 64

yD8900 67

yD8010W 70

DLP Projector - User’s Manual

This publication, including all photographs, illustrations and software, is protected under international copyright laws,

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or

warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or

fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes

from time to time in the content here without obligation of the manufacturer to notify any person of such revision or

changes.

About this manual

This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible,

relevant information such as an illustration and its description has been kept on one page. This printer-friendly format is

both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print

sections that are relevant to your needs.

DLP Projector - User’s Manual

IMPORTANT SAFETY INSTRUCTIONS

Thank you for your purchase of this quality product! For best performance, please read this manual carefully as it is your

guide through the menus and operation.

1. Read and Keep these instructions.

2. Heed all warnings.

3. Follow all instructions.

4. Do not use this apparatus near water. And not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

5. Clean only with a dry cloth.

6. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.

7. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or

the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electri-

cian for the replacement of the obsolete outlet.

8. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the

point where they exit from the apparatus.

9. Only use the attachments/accessories specified by the manufacturer.

10. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus to avoid injury from tip-over.

11. Unplug this apparatus during lightning storms or when unused for long periods of time.

12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in

any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the ap-

paratus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

13. The +12V trigger only outputs 12V DC signal for triggering. Do not connect to any other power input or output.

This could cause damage to this unit.

14. Keep the packing material in case the equipment should ever need to be shipped.

15. Never look into the lens when the projector is on.

AVOID EYE CONTACT TO THE LIGHT

DLP Projector - User’s Manual

Disposal of old electrical and electronic equipment

(Applicable throughout the European Union and other European countries with separate collection programs)

This symbol found on your product or on its packaging, indicates that this product should not

be treated as household waste when you wish to dispose of it. Instead, it should be handed

over to an applicable collection point for the recycling of electrical and electronic equipment. By

ensuring this product is disposed of correctly, you will help prevent potential negative conse-

quences to the environment and human health, which could otherwise be caused by inappro-

priate disposal of this product. The recycling of materials will help to conserve natural resources.

This symbol is only valid in the European Union. If you wish to discard this product, please

contact your local authorities or dealer and ask for the correct method of disposal.

Important Recycle Instructions:

Lamp(s) inside this product contain mercury. This product may contain other electronic waste

that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local,

state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.

EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG.

DLP Projector - User’s Manual

INTRODUCTION

About This Manual

This User’s Manual describes how to install, set up and operate the D8800/D8900/D8010W. Throughout this manual,

the Projector is referred to as the “D8800/D8900/D8010W.”

Target Audience Vivitek has prepared this manual to help installers and end users get the most out of the D8800/

D8900/D8010W. Vivitek has made every effort to ensure that this manual is accurate as of the date it was printed. How-

ever, because of ongoing product improvements and customer feedback, it may require updating from time to time. You

can always find the latest version of this and other Vivitek product manuals on-line, at www.vivitekcorp.com.

Description, Features and Benefits

The Vivitek D8800/D8900/D8010W provide state-of-the-art technology for full HD (1920 x 1200, WUXGA 16:10) native

resolution for crystal clear, pristine images. The D8800/D8900/D8010W offer incredibly high definition images at to-

day’s highest avail-able resolutions. Equipped with precision optics, the D8800/D8900/D8010W include zoom, focus and

lens shift controls for a throw range of 1.85:1 to 2.40:1. For a smaller throw distance (1.56:1 to 1.86:1), the D8800/D8900/

D8010W can be fitted with a varying optics package (optional) to meet different requirements. Exceptional scaling and

film-to-video (3:2 pull-down) conversion is easily achieved. Combined with Vivitek’s sophisticated parameters for white

balancing, the D8800/D8900/D8010W’s proprietary de-interlacing technology provides the highest level of develop-

ment for gray-scale and color balancing and artifact-free images. Completing this engineering marvel are discrete infra-

red (IR) and RS-232 control, power and source selection controls for seamless, flexible operation.

 Key Features and Benefits

The D8800/D8900/D8010W offer these key features and benefits:

yNative Resolution: 1920 x 1080 (16:10 Native Aspect Ratio).

yDLP system using high-performance Digital Micromirror Device (DMD).

yHDMI 1.3 Input with High-bandwidth Digital Content Protection (HDCP).

yHDTV Compatible.

yExcellent Video Processing on progressive and interlaced video inputs.

 Green Product with:

yLead free solder used for soldering including circuit and component electronics.

yLead free glasses and coatings.

yRecycled paper used in the user manuals and packing cartons.

yEnergy Saving: High efficiency power switching and less than 0.5W power consumption in standby mode.

DLP Projector - User’s Manual

 Additional Features of the D8800/D8900/D8010W

yHorizontal and vertical lens shift.

yKeystone adjustment.

Parts List

Your D8800/D8900/D8010W is shipped with the following items, if any items are missing or damaged, please contact

your dealer or Vivitek Customer Service.

Accessory Box List D8800/D8900/D8010W

Item Manual Assy Q’ty EU/ASIA/US/TWN China

CD-ROM 1

● ●

WARRANTY CARD (US/EUR) 1

●

WARRANTY CARD (CN) 1 -

●

RoHS Card (CN) 1 -

●

QC Pass Card (CN) 1 -

●

Important Information (CN) 1

● ●

POWER CORD 125Vac USA 1

●

POWER CORD 250Vac EUR 1

●

POWER CORD 250Vac CHINA 1 -

●

VGA Signal cable 1

● ●

SCREW M M4*0.7*70 PAN C SUS 1

● ●

BATTERY 2

● ●

REMOTE 1

● ●

MODULE COLOR TYPE COLOR WHEEL 1

● ●

DLP Projector - User’s Manual

CONTROLS AND FUNCTIONS

D8800/D8900/D8010W at a Glance

Air outlet

Adjustable

feet*4

Power inlet

Rear Infre-red window

(remote control)

Power switch

Air inlet

yAir outlet

Warm air exits the projector through this vent. Ensure

that it is not blocked.

yAir inlet

Internal fans draw cool air into the projector through

this vent.

yAdjustable feet

Use these when the projector is installed in a table-

top configuration to level the image and/or adjust the

projection angle.

yPower Inlet

For input power from wall outlet to projector.

yRear Infre-red window

For receive the remote controller’s message.

DLP Projector - User’s Manual

I/O Panel

IN SDI OUT

LAN

HDMI

DVI-D

RGB

B/Pb G/YR/Pr

WIRED REMOTE TRIGGER

RS-232

S-VIEDOVIEDO

ySDI

Connect a BNC cable from a serial digital interface (SDI) device.

yHDMI

Connect an HDMI source.

yDVI

Connect a DVI source.

yComponent

Connect a Component (YUV HS/VS-CS) source.

yWIRED REMOTE

Wired input from a Niles- or Xantech-compatible, infrared (IR) repeater system.

yTRIGGER

(3.5-mm, mini phone jack) Offers 12 (+/- 1.5) V of output for 350mA monitor relay with short circuit protection.

yS-VIDEO

A standard S-Video input for connecting a DVD player, satellite receiver or Super VHS (S-VHS) VCR.

yVIDEO

Standard composite video input for connecting a VCR, laser disc player or other composite video source. Also pro-

vides composite sync input for RGBS sources.

yLAN

Connect an RJ45 ethernet cable.

yRGB

Provides a standard, 15-pin VGA-style connection to either an RGB or component high-definition source, or to a

personal computer.

The D8800/D8900/D8010W automatically detect the input signal resolution.

yRS-232

9-pin D-sub connector for interfacing with a PC or home theater automation/control system.

DLP Projector - User’s Manual

KEYPAD

MENU EXIT

POWER INPUT AUTO SYNC ASPECT OPEN CLOSE

SHUTTER

LENS

SHIFT

FOCUS ZOOM

yPOWER

Use the button to turn on/off the projector.

yINPUT

Press to select a video source. HDMI, DVI, VGA, Component / BNC Composite, S-Video or 3D-SGI.

Press this to re-acquire the current active source.

yASPECT

Press this to change the aspect ratio of the current image.

ySHUTTER

Use the buttons to turn on/off shutter.

yMENU

Press this button to show or hide the OSD menu.

yENTER, , , , 

Use these buttons to select items or settings, adjust settings or switch display patterns.

yEXIT

Press this to go one menu higher or exit the OSD menu.

yLENS SHIFT

Button to shift control of the lens, up/down or left/right.

yFOCUS

Button to focus the projected image.

yZOOM

Button to zoom in/out the lens.

DLP Projector - User’s Manual

y ON

Use this button to turn the projector on.

y OFF

Use this button to turn the projector off.

y FOCUS

Focuses the projected images.

y ZOOM

Zoom in/out the projected image.

y TEST PATTERN

Use this to enter test pattern menu.

y LENS SHIFT

Button to shift control of the lens, up/down or left/right.

y ENTER, , , , 

Use these buttons to select items or settings, adjust settings or switch

display patterns. ENTER: Press to select a highlighted menu item or confirm

a changed setting.

y MENU

Press this button to show or hide the OSD menu.

y EXIT

Press this to go one menu higher or exit the OSD menu.

y INPUT

Press to select a input source.

y PICTURE

Starts the PICTURE function.

y NETWORK

Press this to enter the Network (LAN) menu.

y AUTO SYNC

Press this to re-acquire the current active source.

y ASPECT

Selection Button: Press this button repeatedly to select one of the following

aspect ratios: 16 : 9: For viewing 16:9 DVDs or HDTV programs in their native

aspect ratio.

y PIP

Press this to display the picture-in-picture screen.

y OVERSCAN

Press to select an overscan mode.

y FREEZE

Freeze/unfreezes the on-screen picture.

y LAMP MODE

Press this to select a higher or lower brightness setting.

y 3D MODE

This function is not available for this model.

y INFO.

Starts the SERVICE function.

y LIGHT

Press this to turn on remote control backlight.

y CLEAR

Not available

y SHUTTER

Use the button to turn on/off shutter.

y ID SET

Not available

Remote control

FOCUS ZOOM

LENS SHIFT

TEST

PATTERN

MENU EXIT

POWER

OFF

ENTER

INPUTPICTURE NETWORK

AUTO SYNC

ASPECTPIP

OVERSCAN

FREEZE

LAMP MODE

3D MODE INFO.LIGHT

CLEAR SHUTTERID SET

123

456

Notes on Remote Control Operation

y In most situations, you can simply point the remote control at the screen which will reflect the IR signal from the re-mote back

toward the IR receiver on the projector. In some cases, however, ambient conditions may prevent this. If so, point the remote

control at the projector and try again.

y If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.

y The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting.

DLP Projector - User’s Manual

To install batteries in the remote control

STEP 1 STEP 2 STEP 3

1. Slide the battery compartment cover in the direction of the arrow to remove it.

2. Install two AA batteries with the correct polarity.

3. Replace the cover.

Notes on Batteries

y Make sure that the battery polarities are correct when installing the batteries.

y Do not mix an old battery with a new one or different types of batteries.

y If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage.

Range of effective remote control signal reception

30°

IR Reception eective Angles: 30°

IR Reception eective distance: 10m

10m

Note:

Avoid placing the remote control at places of high temperature or humidity as it could cause the remote control to malfunction.

DLP Projector - User’s Manual

Installation Considerations

Proper installation of your projector will ensure the quality of your display. Whether you are installing a projec-

tor temporarily or permanently, you should take the following into account to ensure your projector performs

optimally.

Ambient Light

In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your images will be noticeably

reduced if light directly strikes the screen, such as when a shaft of light from a window or floodlight falls on the image.

Images may then appear washed out and less vibrant.

Requires separate room Installation cost is usually higher.

Throw Distance

Throw distance is the distance measured from the front of the projector to the screen. This is an important calculation in

any projector installation as it determines whether or not you have enough room to install your projector with a de-sired

screen size and if your image will be the right size for your screen. You can quickly estimate the throw distance by taking

the width of the screen and multiplying it by the lens throw ratio; see the image as following. The result of this calcula-

tion tells you roughly how far back the projector should be positioned from the screen in order to project a focused im-

age large enough to fill the screen.

Screen Width (W)

Throw Distance (TD) = Screen Width (W) x Throw Ratio (TR)

Throw Distance (TD)

Two models of the D8800/D8900/D8010W are available, one with 1.56-1.86:1 lens and the other with 1.85-2.40:1 lens

With optional zoom adaptors throw ratios of 1.24 – 3.0 can be achieved. The standard D8800/D8900/D8010W offer

throw ratios between 1.85:1 and 2.40:1. With the optional, short-throw lens, the D8800/D8900/D8010W offer throw

ratios between 1.56:1 and 1.86:1.

DLP Projector - User’s Manual

Modes of installation

 Frontal projection - desktop installation

Advantages: easy to install can be easily moved or adjusted

easy to operate.

Disadvantage: occupies floor space and limits seating

capacity.

Projector

 Rear projection - desktop installation

Advantage: the projector is completely hidden from plain

view the projector can be easily operated this

setup usually offers better reduction of ambi-

ent noise.

Disadvantage: requires an additional room for installation

relatively higher costs for installation.

Projector

 Frontal projection - ceiling mode

Advantage: does not occupy floor space does not draw

attention to it. Eliminates the possibility that

someone would accidentally move the projec-

tor.

Disadvantage: stricter installation requirements and

conditions; care should be taken during

the installation to ensure the projector has

been securely mounted. Operation of the

projector becomes inconvenient without the

remote control.

Projector

 Rear projection - ceiling mode

Advantage: the projector is completely hidden from plain

view this setup usually offers better reduction

of ambient noise.

Disadvantage: requires an additional room for installa-

tion. Stricter installation requirements and

conditions; care should be taken during

the installation to ensure the projector has

been securely mounted. Operation of the

projector becomes inconvenient without the

remote control.

Projector

DLP Projector - User’s Manual

Allow at least 50 cm clearance around the exhaust vent.

The device need to have enough space to prevent issues as stated in this image.

Side Way

50cm

Or Greater

50cm

Or Greater

Back Side

70cm

Or Greater

Celling Mount

30cm

Or Greater

DLP Projector - User’s Manual

Lens Shift

Vertical Lens Shift

The D8800/D8900/D8010W have a lens shift capability which allows the vertical movement of the image without mov-

ing the projector. Lens shift is generally expressed as a percentage of the screen height. For ceiling mounted projectors,

the lens can be moved 50% (0.6V) downward, while the lens can be moved 50% (0.6V) up or down on a desktop mount-

ed projector.

Desktop Front Projection

Height of projected image

Vertical Shift

Max.

0.5V

Max.

0.5V

Ceiling Front Projection

Vertical Shift

Max.

0.5V

Note:

This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this exam-

ple.

Horizontal Lens Shift

The D8800/D8900/D8010W have a lens shift capability which allows the horizontal movement of the image without

moving the projector. The lens can be moved 10% (0.1H) to the right or left within the housing.

Max.

0.5V

0.1H

0.1H1H

Width of projected image

Shift to Left Shift to Right

Normal Projection Position

Note::

This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this exam-

ple.

DLP Projector - User’s Manual

Connecting the projector to other devices.

Proceed as follows to connect the D8800/D8900/D8010W to your video sources, external controller(s) - if present - and

AC power. When connecting your equipment: •Use the correct signal cables for each source. •Ensure that the cables are

securely connected. Tighten the thumbscrews on connectors that have them. Connecting Source Components to the

D8800/D8900/D8010W Connect your video sources to the D8800/D8900/D8010W as shown and described in the sec-

tions that follow.

HDMI Connection

IN SDI OUT

LAN

HDMI

DVI-D

RGB

B/Pb G/YR/Pr

WIRED REMOTE TRIGGER

RS-232

S-VIEDOVIEDO

DVI Source(s)

(BD/HD-DVD/DVD Player, HD SetTop Box, Game Console etc.)

Trigger connection

If your home theatre system includes a projector screen, screen cover or other 12V Trigger equipment, please connect

such device/equipment to the projector’s 12V Trigger output as illustrated. After you have done so, your screen will lower

automatically whenever you turn on your projector for your convenience.

Tip = +12V

Sleeve = Ground

Retractable screen or other

12V device

Projector Screen

B/Pb G/YR/Pr

WIRED REMOTE TRIGGER

RS-232

S-VIEDOVIEDO

DLP Projector - User’s Manual

IR Input connection

If infrared signals from the remote control cannot reach the projector due to excessive distance or obstructions such as

walls or cabinet doors, you can connect an external IR repeater system to the IR INPUT on the D8800/D8900/D8010W to

extend the range of the remote control.

IR sensor

IR repeater

Remote control

B/Pb G/YR/Pr

WIRED REMOTE TRIGGER

RS-232

S-VIEDOVIEDO

S-VIDEO, VIDEO connection

If the image input device offers both S-Video and Video connection, it is recommended that you choose S-Video to obtain

better image quality. If both the S-Video and Video inputs are connected to the projector, the projector will prioritize S-

Video signal input and image from the Video input will not be played.

IN SDI OUT

LAN

HDMI

DVI-D

RGB

B/Pb G/YR/Pr

WIRED REMOTE TRIGGER

RS-232

S-VIEDOVIEDO

DVD player, VCR, satellite receiver,

LD and so forth

DLP Projector - User’s Manual

COMPONENT connection

Take the 3/5 cabled RGB component video connectors from the source equipment to the projector’s COMPONENT jacks.

IN SDI OUT

LAN

HDMI

DVI-D

RGB

B/Pb G/YR/Pr

WIRED REMOTE TRIGGER

RS-232

S-VIEDOVIEDO

DTV set-top-box or other compo-

nent (YPbPr) input source

Y PbPr

RS-232 Connection

Connect a PC or home theater control/automation system (if present) to the RS-232 port on the D8800/D8900/D8010W.

Use a standard, 9-pin serial cable, wired straight-through.

IN SDI OUT

LAN

HDMI

DVI-D

RGB

Desk Top or Notebook

Page is loading ...

Vivitek D8800 User manual

Brand: Vivitek

Model: D8800

Category: Data projectors

Type: User manual

Download PDF

report

Vivitek D8800 User manual

Vivitek D8800 User manual

Related papers

Other documents