Linortek ITRIXX­-WFMN Wireless WiFi Hour Meter Operating instructions

ITRIXX­-WFMN Wireless WiFi Hour Meter
Brand
Linortek
Model
ITRIXX­-WFMN Wireless WiFi Hour Meter
Type
Operating instructions

Linortek ITRIXX­-WFMN Wireless WiFi Hour Meter is a versatile IoT controller and runtime meter designed to monitor and record the runtime hours of up to two different pieces of equipment. With its digital and analog inputs, and relay outputs, it offers various triggering and notification options. The device can be easily integrated into existing equipment to track usage and maintenance intervals. The WiFi connectivity enables remote monitoring and data collection, allowing you to access runtime information and manage your equipment efficiently.

Linortek ITRIXX­-WFMN Wireless WiFi Hour Meter is a versatile IoT controller and runtime meter designed to monitor and record the runtime hours of up to two different pieces of equipment. With its digital and analog inputs, and relay outputs, it offers various triggering and notification options. The device can be easily integrated into existing equipment to track usage and maintenance intervals. The WiFi connectivity enables remote monitoring and data collection, allowing you to access runtime information and manage your equipment efficiently.

ThankyouforpurchasingtheLinortekITrixxWFMNWirelessHourMeter.TheiTrixxisanIoTcontrollerandruntimemeterwith
digitalinputs,analoginputsandrelayoutputscapableoftrackingruntimehoursofuptotwodifferentpiecesofequipment.Forthe
completesettinginstructions,pleaserefertotheiTrixxWFMNOwnersandOperationManual,whichcanbedownloadedhere:
https://www.linortek.com/downloads/documentations/
WHAT'SINTHEBOX
Pleaseinspectthecontentsofyourproductkit.EachSERVERissentinitsownboxandincludes:
____OneiTrixxWFMNSERVER
____One12VDCPowerSupply
____2WagoConnectors
____One2.2kOhmResistorKit
____iTrixxWFMNQuickSetupInstruction
ITRIXXWFMNWIRECHART
Thereis1cableontheiTrixxWFMNDi,and3cablesontheiTrixxWFMNADi.Fromthetoptobottom,theyaremarkedascable1,
2,3.Seethechartbelowforexplanation.
Cable1:AnalogInputs(foriTrixxWFMNADionly)
Cable2:RelayOutputs(foriTrixxWFMNADionly)
Cable3:DigitalInputsandPowerInput
WireColor Function Note
Green Ain1 Analog1
Brown Return
Red 5V If12Vsensor,usa12Vpowersupply
White Ain2 Analog2
Blue Return
Black 5V If12Vsensor,usa12Vpowersupply
WireColor Function Note
Brown Relay1NC Relay1
Green Relay1C
Red Relay1NO
Blue Relay2NC Relay2
White Relay2C
Black Relay2NO
iTrixxWFMNDiHardware iTrixxWFMNADiHardware
1
ITRIXXWFMNQUICKSETTINGINSTRUCTION
w/WPA2EnterpriseVersionSoftware
ITRIXXWFMNWIRECHART
Thereis1cableontheiTrixxWFMNDi,and3cablesontheiTrixxWFMNADi.Fromthetoptobottom,theyaremarkedascable1,
2,3.Seethechartbelowforexplanation.
Cable1:AnalogInputs(foriTrixxWFMNADionly)
Cable2:RelayOutputs(foriTrixxWFMNADionly)
Cable3:DigitalInputsandPowerInput
2
WireColor Function Note
Red 1248VDC PowerInput
Black Ground
Green DIN1A Input1,524VDC.Ifusingavoltage
above12VDCforadigitalinput,you
mustusea2.2Kohmresistor.
White DIN1C
Brown DIN2A Input1,524VDC.Ifusingavoltage
above12VDCforadigitalinput,you
mustusea2.2Kohmresistor.
Blue DIN2C
ACTIVATETHEMETER
TheITrixxWFMNisdesignedtobeintegratedintoexistingequipmenttomonitorruntime.InstallingyouriTrixxwillinvolvetapping
circuitsontheequipmentyouintendtomonitor.
TheiTrixxHourMeterhastwoseparatehourcounters.Thehourcountersmaybeactivatedinanumberofdifferentways.
1.InthesimplestsetuptheiTrixxmaybeactivatedwheneverpowerisappliedtotheunit.Inthiscase,iftheiTrixxison,itis
counting.AvoltagethresholdisprovidedsotheiTrixxmaystopcountingaspowerislosttopreventmemorycorruption.Inthis
way,youonlyneedtoconnecttheiTrixxtothesamepowersourceoftheequipmentyouwishtocollectrunningdata,noother
wiringrequired.
2.Youmayalsouseoneoftheinputstoturncountingonandoff.TherearetwodigitalinputsintheiTrixx.Thedigitalinputs
allowiTrixxtodetectanexternalon/offstateofasensor.
Tousethemeteronamobileequipment,aconstant1248VDCpowersourcefromabattery,andaseparate548VDCcircuitthat
turnsonandoffwiththevehicle.AconstantpowersourceispreferabletopoweryourWifimeterbecauseitwillalwaysbeon.If
themeterhastobootupwhenyourequipmentispoweredon,youmaynothaveanaccuratereading.TheWiFimeteratidle
drawsapproximately70mA.Itwillnotdrainthebatteryunlessitisleftforanexceptionallylongtime.
3.Alternatively,itcanbeconfiguredtofollowoneoftherelayssuchthatwhentherelayisactivatedtheiTrixxwillcount(for
iTrixxWFMNADiunitonly).TherelaysontheiTrixxWFMNADiaredrycontactrelaysandnormallyopen.
MostcommonusecaseistowireadigitalinputtothesamepowersourceofyouriTrixxServertotriggerthemeter,sowhenyour
equipmentison,iTrixxiscounting.
MAKECONNECTIONS
RelayConnection(iTrixxWFMNADi)
YouriTrixxWFMNADiserverhastwo5VDCrelayoutputs.Theserelaysarelimitedtoa5Vsignalandareprewiredtotheoutsideof
theenclosure.Thereare3positionsontheterminalNO(NormallyOpen),C(Common),andNC(NormallyClosed).
Additionally,thereisaswitchforeachrelayontheboard.Foradrycontactrelay,pushtheswitchtotheright,todrivea5VDC
signal,pushtheswitchtotheleft.(SeeBoardLayoutReferencesectiontolocatetherelayoutputwires).
AnoteofCAUTION:Theseunitsaregroundisolated.AlwaysconnectsothatpowerloopisonlyconnectedtotheiTrixxunit.Do
NOTuseexternalgroundconnections.DoingsomaydamagetheSERVERorPOEoriginatingdevice.
DigitalInputsConnection
iTrixxservershave2digitalinputs(524VDC)builtintotheboard.ThedigitalinputsallowtheSERVERtodetectanexternalon/off
stateofasensor.WiththisinformationtheSERVERcandisplaywhetheraninputisonoroff,counteventsinaresettableornon
resettablecounter,andcalculatethefrequency(suchasforuseasatachometer)ortheperiodoftheinput.SeeBoardReference
Layoutpagetolocatethedigitalinputwires.Acircuitthatswitchesonandoffwithyourequipmentcanbewiredtothisdigitalinput
todetectwhetherornotyourmachineisrunning.Note:Ifusingacircuitabove12VDCyoumustincludea2.2kohmresistor
betweenthetappedcircuitandtheiTrixx.TheiTrixxwillonlydetectavoltageonthiscircuitandwillnotdrawanypowerorinterfere
withthiscircuit.DoNOTexceed24VDConyourdigitalinput.Oncewired,seethesectionSetupTriggerstotriggerthehour
counterorsetupnotifications.Forhowtousearesistorforthedigitalinput,pleaserefertothediagrambelow:
Therearetwomodesofoperationforthedigitalinputs:ISOLATEDandPULLUP.ThesearesetatthefactorytoPULLUPby
default.
1)ISOLATEDmodeallowsyoutodirectlydrivetheiTrixx’soptoisolatorwithanexternalvoltagethoughaninternal1K
resistor.Thisvoltagemaybeintherangeof5VDCto24VDCsupplyingaminimumof2mAoramaximumof30mAtothe
optoisolatordiode.Thereisnootherinternalconnectiontothisvoltagesoitisanisolatedinput.TheDINinthismodewill
defaulttoaLowstate.Tosetthismode,movetheDINswitchtotheright(Towardscenterofboard).
2)PULLUPmodeconnectsa1Kresistortoaninternalvoltageallowingyoutouseasimpleswitch(suchasamagnetic
doorswitch)acrossterminals1and2.Whentheswitchisactivatedasignalissenttotheinput.Thesemodesareselected
bytheswitchontheserver(seetheBoardLayoutforreference).TheDINinthismodewilldefaulttoaHighstate.To
setthismode,movetheDINswitchtotheLeft(Towardsedgeofboard).
Caution:Ifyouintendtouseisolatedmode,verifyinputswitchissettoISObeforeapplyinganexternalvoltage.Doingotherwise
maydamagetheSERVERorPOEoriginatingdevice.
TowireyourequipmenttotheiTrixx’sdigitalinput,identifyacircuitof5–24VDCthatswitchesonandoffwithyourequipment.
WirethistoDIN1orDIN2onyouriTrixx.
AnalogInputsConnection(iTrixxWFMNADi)
TheanaloginputsallowtheSERVERtoreadthevalueofexternalequipment.iTrixxWFMNADihas2analoginputs(5v420mA)built
intotheboard.The2analoginputwiresareconnectedtononisolated05Vcurrentsensorswhichmaybeconnectedtoavarietyof
devicessuchastemperatureorpressuresensors.TheSERVERprovidesagroundandpowerconnectionsothatmeasurementscan
bemadewithoutexternalvoltagereferences.Youshoulduseasensorthatisisolatedsothattheitmakesnoconnectiontoaremote
ground.Thisinformationcanbesettotriggeranotification.Thereare3wiresforeachanaloginput,seeBoardReferenceLayout
pagetolocatetheanaloginputwires.
AnoteofCAUTION:Theseunitsaregroundisolated.AlwaysconnectsothatpowerloopisonlyconnectedtotheiTrixxunit.Do
NOTuseexternalgroundconnections.DoingsomaydamagetheSERVERorPOEoriginatingdevice.
OnceyouarefinishedwiringtheiTrixxtoyourequipment,youmaythenpoweronyourequipmentorreconnectthevehicle’sbattery
andconfigureyourdevice.
3
CONNECTTOYOURNETWORK
1.BeforepoweringuptheiTrixx
ToconfigureyouriTrixx,youwillneedthefollowinginformationduringthesetupprocess,wesuggestyoutogatherthatinformation
beforeputtingyourdeviceinProvissioningMode,becauseonceyouputyourdeviceinProvisioningMode,youwillhave2minutesto
connectittoyournetworkbeforethismodetimesout.
1)Yournetworkname,usernameandpasswordforWPA2Enterprisesecurityprotocol.
2)Writedownthelast6charactersofyourdevice’sMACaddress,thiswillbethepasswordtologintoyouriTrixxserver
whenyouconfigthesoftwareonTelnet.YoucanfindtheMACaddressatthebackofyourdevice.
3)UseyourwebbrowsertoconnecttheiTrixxServertoyournetwork,onlyFirefoxbrowseriscurentlysupported.SincetheiTrixx
configpageisnotencrypted,youneedtodisabletheHTTPSOnlymodeonyourbrowserfirst.TodisabletheHTTPSOnlymode,
openyourFirefoxbrowser,gotoSettingsPrivacy&SecuritySetting,scrolldowntothebottomofthepage,ontheHTTPSOnly
Modesection,selectDon’tEnableHTTPSOnlyMode.
4)UseTelnetclientforinitialsetupofyouriTrixxdevice.TouseTelnetonWindows8.1orWindows10,followthestepsbelow:
•OpenControlPanel
•SelectPrograms
•UnderProgramsandFeaturesselectTurnWindowsfeaturesonoroff
•ScrolldownandselectthecheckboxforTelnetClientandclickOK
5)DownloadtheHourCollectordesktopAppfromourwebsitedownloadpage,thisfreetoolcanhelpyoutofindtheIP
addressonyournetwork,aswellasfordatacollection/monitoring.Beforedownloading,ensureyourcomputerhasJavainstalled.
Javaisavailablefordownloadhere:https://www.java.com/en/.TheHourCollectorappwillautomaticallylocateyouriTrixxand
allowsforquickaccess.TheHourCollectorappwillnotimmediatelylocatetheiTrixxifnotconnectedviaEthernet.TheiTrixxwill
appearoncetheHourCollectorupdatesafterreceivingdatafromiTrixxdevices.TheHourCollectorappupdateseverytwominutesby
default.Youcandownloadthistoolhere:https://www.linortek.com/downloads/supportprogramming/
2.PoweringiTrixx
YouriTrixxserverissuppliedwitha12VDCpowersupply.YoumaypoweryouriTrixxserverusingthispowersupplyforinitialsetup
andsoftwareconfiguration.Onceyourinitialsetupiscompleted,youcanwireyouriTrixxtoyourequipmentbytappingintoa12–
48VDCcircuitonyourequipment.
ToconnecttheiTrixxtothe12VDCpowersupply,findtheRED(+)andBlack()wiresfromCable3,connecttheREDwiretothe
positivewireofthepowersupply,BLACKwire3tothenegativewire(markedwithwhitestrip)onthepowersupply.Oncepowered,
youriTrixxserverisreadytobeconnectedtoyournetwork.
3.ConnectingiTrixxtoWiFiNetwork
ToconnecttheiTrixxtoyournetwork,followthestepsbelow:
1)OpenthecoveroftheiTrixx,locatetheDFLTbutton,pushandholdtheDFLTbuttonwithapaperclipuntiltheblueLEDstarts
flashing.YourdeviceisnowinProvisioningMode.Youhave2minutestoconnectittoyournetworkbeforethismodetimesout.
OncetheProvisioningmodetimesout,youwillneedtorepeatthefirststepandputitinProvisioningmode.
2)UseaWiFienabledPCoramobiledevicetoconnecttoyourserver’sAP(WiFienableddeviceisonlyrequiredfortheinitial
setup,onceyouhaveconnectedyouriTrixxtoyournetwork,youcanuseanyPConthesamenetworktoconfigthedevice).If
youuseaPC,clicktheNetworkiconattherightsidecorner,theiTrixxwillbedisplayedasaWiFinetworknamed
WiFiHM_xx:xx:xx(Thex’smakeupthelast6charactersofyourdevice’sMACaddress)
3)Whenpromptedenterthepassword:wifihmpsk
4)Onceconnectedyoumayreceiveamessagestatingthereisnointernetconnection.Disregardthismessage.
5)OpenyourFirefoxwebbrowser,typeinthisURL:http://192.168.1.1.Note:Pleasemakesureyourbrowserdoesn’tchangehttp
tohttps!
6)EnteryourWiFinetworkname,selectWPA2EnterprisefromtheSecuritybox,entertheUsernameandPassphraseforyour
network.
7)ClickConnect.TheBlueLEDonyourdevicewillstopblinkingandstayonsolid.YouriTrixxserverisnowconnectedtoyour
network,atthistime,yourcomputershouldconnectbacktoyournetwork.Ifit’snotautomaticallyswitchedtoyournetwork,click
thenetworkicononyourcomputer,andselectthesamenetworkyouriTrixxconnectedtoinourpreviousstep.
Troubleshooting:IfyouareunabletoconnecttheiTrixxtoyourWiFinetwork(errormessage:rejecttoconnect),thisisbecause
yourWiFisecurityblocksunrecognizedSSIDs,pleasecontactyourITdepartmenttowhitelisttheSSIDfortheiTrixxdevice.
MAKECONNECTIONS
RelayConnection(iTrixxWFMNADi)
YouriTrixxWFMNADiserverhastwo5VDCrelayoutputs.Theserelaysarelimitedtoa5Vsignalandareprewiredtotheoutsideof
theenclosure.Thereare3positionsontheterminalNO(NormallyOpen),C(Common),andNC(NormallyClosed).
Additionally,thereisaswitchforeachrelayontheboard.Foradrycontactrelay,pushtheswitchtotheright,todrivea5VDC
signal,pushtheswitchtotheleft.(SeeBoardLayoutReferencesectiontolocatetherelayoutputwires).
AnoteofCAUTION:Theseunitsaregroundisolated.AlwaysconnectsothatpowerloopisonlyconnectedtotheiTrixxunit.Do
NOTuseexternalgroundconnections.DoingsomaydamagetheSERVERorPOEoriginatingdevice.
DigitalInputsConnection
iTrixxservershave2digitalinputs(524VDC)builtintotheboard.ThedigitalinputsallowtheSERVERtodetectanexternalon/off
stateofasensor.WiththisinformationtheSERVERcandisplaywhetheraninputisonoroff,counteventsinaresettableornon
resettablecounter,andcalculatethefrequency(suchasforuseasatachometer)ortheperiodoftheinput.SeeBoardReference
Layoutpagetolocatethedigitalinputwires.Acircuitthatswitchesonandoffwithyourequipmentcanbewiredtothisdigitalinput
todetectwhetherornotyourmachineisrunning.Note:Ifusingacircuitabove12VDCyoumustincludea2.2kohmresistor
betweenthetappedcircuitandtheiTrixx.TheiTrixxwillonlydetectavoltageonthiscircuitandwillnotdrawanypowerorinterfere
withthiscircuit.DoNOTexceed24VDConyourdigitalinput.Oncewired,seethesectionSetupTriggerstotriggerthehour
counterorsetupnotifications.Forhowtousearesistorforthedigitalinput,pleaserefertothediagrambelow:
Therearetwomodesofoperationforthedigitalinputs:ISOLATEDandPULLUP.ThesearesetatthefactorytoPULLUPby
default.
1)ISOLATEDmodeallowsyoutodirectlydrivetheiTrixx’soptoisolatorwithanexternalvoltagethoughaninternal1K
resistor.Thisvoltagemaybeintherangeof5VDCto24VDCsupplyingaminimumof2mAoramaximumof30mAtothe
optoisolatordiode.Thereisnootherinternalconnectiontothisvoltagesoitisanisolatedinput.TheDINinthismodewill
defaulttoaLowstate.Tosetthismode,movetheDINswitchtotheright(Towardscenterofboard).
2)PULLUPmodeconnectsa1Kresistortoaninternalvoltageallowingyoutouseasimpleswitch(suchasamagnetic
doorswitch)acrossterminals1and2.Whentheswitchisactivatedasignalissenttotheinput.Thesemodesareselected
bytheswitchontheserver(seetheBoardLayoutforreference).TheDINinthismodewilldefaulttoaHighstate.To
setthismode,movetheDINswitchtotheLeft(Towardsedgeofboard).
Caution:Ifyouintendtouseisolatedmode,verifyinputswitchissettoISObeforeapplyinganexternalvoltage.Doingotherwise
maydamagetheSERVERorPOEoriginatingdevice.
TowireyourequipmenttotheiTrixx’sdigitalinput,identifyacircuitof5–24VDCthatswitchesonandoffwithyourequipment.
WirethistoDIN1orDIN2onyouriTrixx.
AnalogInputsConnection(iTrixxWFMNADi)
TheanaloginputsallowtheSERVERtoreadthevalueofexternalequipment.iTrixxWFMNADihas2analoginputs(5v420mA)built
intotheboard.The2analoginputwiresareconnectedtononisolated05Vcurrentsensorswhichmaybeconnectedtoavarietyof
devicessuchastemperatureorpressuresensors.TheSERVERprovidesagroundandpowerconnectionsothatmeasurementscan
bemadewithoutexternalvoltagereferences.Youshoulduseasensorthatisisolatedsothattheitmakesnoconnectiontoaremote
ground.Thisinformationcanbesettotriggeranotification.Thereare3wiresforeachanaloginput,seeBoardReferenceLayout
pagetolocatetheanaloginputwires.
AnoteofCAUTION:Theseunitsaregroundisolated.AlwaysconnectsothatpowerloopisonlyconnectedtotheiTrixxunit.Do
NOTuseexternalgroundconnections.DoingsomaydamagetheSERVERorPOEoriginatingdevice.
OnceyouarefinishedwiringtheiTrixxtoyourequipment,youmaythenpoweronyourequipmentorreconnectthevehicle’sbattery
andconfigureyourdevice.
4
CONNECTTOYOURNETWORK
1.BeforepoweringuptheiTrixx
ToconfigureyouriTrixx,youwillneedthefollowinginformationduringthesetupprocess,wesuggestyoutogatherthatinformation
beforeputtingyourdeviceinProvissioningMode,becauseonceyouputyourdeviceinProvisioningMode,youwillhave2minutesto
connectittoyournetworkbeforethismodetimesout.
1)Yournetworkname,usernameandpasswordforWPA2Enterprisesecurityprotocol.
2)Writedownthelast6charactersofyourdevice’sMACaddress,thiswillbethepasswordtologintoyouriTrixxserver
whenyouconfigthesoftwareonTelnet.YoucanfindtheMACaddressatthebackofyourdevice.
3)UseyourwebbrowsertoconnecttheiTrixxServertoyournetwork,onlyFirefoxbrowseriscurentlysupported.SincetheiTrixx
configpageisnotencrypted,youneedtodisabletheHTTPSOnlymodeonyourbrowserfirst.TodisabletheHTTPSOnlymode,
openyourFirefoxbrowser,gotoSettingsPrivacy&SecuritySetting,scrolldowntothebottomofthepage,ontheHTTPSOnly
Modesection,selectDon’tEnableHTTPSOnlyMode.
4)UseTelnetclientforinitialsetupofyouriTrixxdevice.TouseTelnetonWindows8.1orWindows10,followthestepsbelow:
•OpenControlPanel
•SelectPrograms
•UnderProgramsandFeaturesselectTurnWindowsfeaturesonoroff
•ScrolldownandselectthecheckboxforTelnetClientandclickOK
5)DownloadtheHourCollectordesktopAppfromourwebsitedownloadpage,thisfreetoolcanhelpyoutofindtheIP
addressonyournetwork,aswellasfordatacollection/monitoring.Beforedownloading,ensureyourcomputerhasJavainstalled.
Javaisavailablefordownloadhere:https://www.java.com/en/.TheHourCollectorappwillautomaticallylocateyouriTrixxand
allowsforquickaccess.TheHourCollectorappwillnotimmediatelylocatetheiTrixxifnotconnectedviaEthernet.TheiTrixxwill
appearoncetheHourCollectorupdatesafterreceivingdatafromiTrixxdevices.TheHourCollectorappupdateseverytwominutesby
default.Youcandownloadthistoolhere:https://www.linortek.com/downloads/supportprogramming/
2.PoweringiTrixx
YouriTrixxserverissuppliedwitha12VDCpowersupply.YoumaypoweryouriTrixxserverusingthispowersupplyforinitialsetup
andsoftwareconfiguration.Onceyourinitialsetupiscompleted,youcanwireyouriTrixxtoyourequipmentbytappingintoa12–
48VDCcircuitonyourequipment.
ToconnecttheiTrixxtothe12VDCpowersupply,findtheRED(+)andBlack()wiresfromCable3,connecttheREDwiretothe
positivewireofthepowersupply,BLACKwire3tothenegativewire(markedwithwhitestrip)onthepowersupply.Oncepowered,
youriTrixxserverisreadytobeconnectedtoyournetwork.
3.ConnectingiTrixxtoWiFiNetwork
ToconnecttheiTrixxtoyournetwork,followthestepsbelow:
1)OpenthecoveroftheiTrixx,locatetheDFLTbutton,pushandholdtheDFLTbuttonwithapaperclipuntiltheblueLEDstarts
flashing.YourdeviceisnowinProvisioningMode.Youhave2minutestoconnectittoyournetworkbeforethismodetimesout.
OncetheProvisioningmodetimesout,youwillneedtorepeatthefirststepandputitinProvisioningmode.
2)UseaWiFienabledPCoramobiledevicetoconnecttoyourserver’sAP(WiFienableddeviceisonlyrequiredfortheinitial
setup,onceyouhaveconnectedyouriTrixxtoyournetwork,youcanuseanyPConthesamenetworktoconfigthedevice).If
youuseaPC,clicktheNetworkiconattherightsidecorner,theiTrixxwillbedisplayedasaWiFinetworknamed
WiFiHM_xx:xx:xx(Thex’smakeupthelast6charactersofyourdevice’sMACaddress)
3)Whenpromptedenterthepassword:wifihmpsk
4)Onceconnectedyoumayreceiveamessagestatingthereisnointernetconnection.Disregardthismessage.
5)OpenyourFirefoxwebbrowser,typeinthisURL:http://192.168.1.1.Note:Pleasemakesureyourbrowserdoesn’tchangehttp
tohttps!
6)EnteryourWiFinetworkname,selectWPA2EnterprisefromtheSecuritybox,entertheUsernameandPassphraseforyour
network.
7)ClickConnect.TheBlueLEDonyourdevicewillstopblinkingandstayonsolid.YouriTrixxserverisnowconnectedtoyour
network,atthistime,yourcomputershouldconnectbacktoyournetwork.Ifit’snotautomaticallyswitchedtoyournetwork,click
thenetworkicononyourcomputer,andselectthesamenetworkyouriTrixxconnectedtoinourpreviousstep.
Troubleshooting:IfyouareunabletoconnecttheiTrixxtoyourWiFinetwork(errormessage:rejecttoconnect),thisisbecause
yourWiFisecurityblocksunrecognizedSSIDs,pleasecontactyourITdepartmenttowhitelisttheSSIDfortheiTrixxdevice.
NetworkListSample WiFiConnectionPage
FINDTHEIPADDRESS
BeforeusingTelnettoconfigtoyouriTrixx,youwillneedtofinditsIPaddressfromyournetwork.
Theeasiestwaytofindyourserver’sIPaddressisbyusingtheLinortekHourCollectorapp.OnceyouopentheHourCollectorApp,it
willdisplayalliTrixxdevicesthatyouhaveinstalledonthesamenetwork.Ifyoucan’tfindtheIPaddress,presstheRESETbutton
withapaperclipanditwillidentifyuponreboot.
Youmayalsofindyourdevice’sIPaddressbysigningontoyourrouterandsearchingthelistofconnecteddevices.YouriTrixxhour
meterwillbeidentifiedonyourrouterasWiFiHM_xxxxxxwherethex’sarethelast6charactersofthedevice’sMACaddress.
TheHourCollectorappwilldisplaythefollowinginformation:
PROGRAMITRIXXFROMTELNET
YouwillneedtouseaTelnetclienttoconfigureyouriTrixxserver.ToconfigureTelnetonWindows8.1orWindows10,followthese
steps:
1)OpenControlPanel
2)SelectPrograms
3)UnderProgramsandFeaturesselectTurnWindowsfeaturesonoroff
4)ScrolldownandselectthecheckboxforTelnetClientandclickOK
ToconnecttotheiTrixxserverusingyourPC,followthesesteps:
1)SearchCommandPromptonyoursearchbar(Windows10),clickandopenCommandPrompt
2)Entertelnetnnn.nnn.nnn.nnn30316wherenisyourdevice’sIPaddress
3)Onceconnected,itwillpromptyouforapassword.Bydefault,thispasswordisthelast6charactersofitsMACaddress–
withoutcolonsandalllowercase–whichcanbefoundprintedontheenclosureortheHourCollectorApp.(ex:cd56ef)
4)Afterenteringyourpassword,allavailablecommandswillbelistedinthecommandpromptwindow.Fordetailsofhowtouse
thecommands,pleaserefertothemanualAppendix1:AvailableCommands.
YoucanalsodownloadaTCPTelnetappforamobiledevicetobeabletosendTelnetcommandstotheWFMNprovidedthemobile
deviceisalsoconnectedtothesameWiFinetwork(doesnotworkoncellularnetwork).
5
ITRIXXSERVERBASICCONFIGURATION
Toconfigureyourserver,youwillneedtoissuecommandsviatheTelnetterminal.Thissectionwillcoverthebasicconfigurationof
yourdevice.Forafulllistofcommandsandsyntax,seethefollowingpages.
IMPORTANTNOTE:Makecertaintousethesavecommandaftermakingchangesotherwiseyourchangeswillbelostwhenyour
serverreboots.
1.Namingyourserver
TomakeyouriTrixxservermoreidentifiableonyournetwork,enterserver=<name>replacing<name>withyourdesiredserver
name.
2.SettingTimeandDate
Bydefault,yourserverisconfiguredforGMT.Toadjustthetimezone,entertimezone=xwherexisyourtimezoneoffset.For
example:timezone=5forEST,timezone=4forEDTifyouareinEasternDayLightSavingtime.Tocheckyourserver’stime,
youmayenterthecommand:time.Thiswilldisplaythecurrenttimeanddateformattedas:yyyymmddThhmmssfollowedbythe
timezoneoffset(ISO8601).Forexample:20200422T1330000400for4/22/20201:30pmGMT4.
YoumayalsosetyourpreferredNTPserverandupdateinterval.Bydefault,youserverusestheNTPserver:time.nist.govand
updatesthetimeevery11minutes.TochangetheNTPserver,enterntphost=<NTPhostname>(ex:ntphost=time.nist.gov).
Tochangetheupdatefrequency,usethecommandntpperiod=xwherexistheupdatefrequencyinminutes(ex:ntpperiod=11)
Note:IfyoubuildadedicatednetworkfortheiTrixxtocollectmachinedatawithoutinternetconnection,theiTrixxserverwillnotbe
abletoreachtheNTPserverandupdateitstime.TomaketheiTrixxservertogetthetimefromyourcomputer,youneedtodisable
theNTPhostwiththiscommand:
ntphost=
OnceyouclicktheDiscoverbuttonontheHourCollectordesktopapp,itwillsendUDPmessagewithcurrentdate/timetotheiTrixx
server.(Thisfeatureisavailableforsoftwareversion0.58.0v.andup)
6
SETUPTRIGGERS
AfterconfiguringyouriTrixxserver,youcanconfiguretriggerstoactivatethedifferentfeaturesofyourdevice.Triggersyntax
consistsof3variables:asource(whatactivatesthetrigger),avalue(therequiredconditionofthesource),andthetarget(what
todo).Continuereadingforadescriptionofeachvariable.Eachvariableisseparatedbyacomma.
TheTriggercommandconfiguresdifferenttypesoftriggersandtheiractions.Thiscommandalsoproduceshandy`triggersdump`
outputaftercreatingthenewtrigger.Youcanuse`save`commandtosaveconfiguredtriggersoitisavailableafterreboot.
Formoreinformationofhowtosetuptriggers,pleaserefertotheproductfullmanualSetupTriggerssections,which
canbedownloadedathttps://www.linortek.com/downloads/documentations/
Herearesomesamplesforthetrigger:
•Toactivaterelay1every30minutes,usethecommand:trigger=time,00.30,relay.1
•Toactivaterelay2everyhour,usethecommand:trigger=time,01.00,relay.2
•Tosendareportevery1.5hoursstartingfrom8thApr2020,6:00pm,usethecommand:
trigger=time,01.30:20200408T1800,report
•Toactivaterelay.1at4thJuly2020,12am,usethecommand:trigger=time,:20200704T0000,relay.1
•Whenrelay2ison,iTrixxstartscountinghourmeter2:trigger=relay.2,high,hm.2
•Whendigitalinput1ison,iTrixxstartscountinghourmeter1:trigger=din.1,high,hm.1
•Wheninputvoltagegreater/equalto3v,iTrixxstartscountinghourmeter1:trigger=voltmon,ge.3:0,hm.1
•Whenanaloginput2valuelessthan3.5,turnrelay2on,whenvalueishigherthan4.1resetthetrigger:
trigger=ain.2,lt.3.5:4.1,relay.2
•Whenhourmeter1isequalto100,sendreport:trigger=hm.1,eq.100,report
•Whentemperatureisgreater/equalto40,turnrelay1on,whentemperatureisbelow35,thetriggerisreset:
trigger=tsensor,ge.40:35,relay.1
•Whenaccelerometervalueisgreaterthan5,sendreport,whenaccelerometerisbelow1,thetriggerisreset:
trigger=shock,gt.5:1,report
Togetareportwhendigitalinput1isstayingonformorethan5minutesyouneedtosettwotriggers:
•trigger=din.1,high,duration.1(Whendigitalinput1ison,iTrixxstartscountingduration1)
•trigger=duration.1,ge.300,report(Whenduration1isgreater/equalto5minutes,sendreport)
Toviewexistingtriggers,usethecommandtriggersdump.Thiscommandwilllistallconfiguredtriggersinanumberedlist.To
deleteatrigger,usethecommandtriggerdelete=xwherexcorrespondstothenumberlistedfromthetriggersdumpcommand.
DATAMONITORING
OnceyouriTrixxiswiredandconfigured,itwillperiodicallyreportitsdataoveryournetwork.Youcanuseanycomputeronthe
samenetworktomonitorthedatausingtheHourCollectorapp,DataCollectorapp,orpublishthehourreadingsasMQTTmessage
andmonitorthedataremotelyfromyourCMMSorothercustomdatabaseaslongastheysubscribetothetopiconyourbrocker.
Fordetailsofhowtousedifferenttoolsfordatamonitoring,pleaserefertotheproductfullmanualDataMonitoringsection.
Forcompleteproductdocumentation,currentsoftware,webpagesandvariousutilities,visithttps://www.linortek.com/downloads/.
Theproductmanual,aswellassoftwareupdates,areavailablefordownload.
CONTACTSUPPORT
Ifyouneedassistanceonsettingyourdevices,pleasefeelfreetocontactus:
Phone:(001)3364856199
Email:[email protected]
Youcanalsostartachatfromourwebsitetoreachoursupportteams.
WinstonSalem,NC27127
[email protected]
Informationsubjecttochangewithoutnotice. www.linortek.com
0150800010C
1022R003V003
PrintedinU.S.A.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Linortek ITRIXX­-WFMN Wireless WiFi Hour Meter Operating instructions

ITRIXX­-WFMN Wireless WiFi Hour Meter
Brand
Linortek
Model
ITRIXX­-WFMN Wireless WiFi Hour Meter
Type
Operating instructions

Linortek ITRIXX­-WFMN Wireless WiFi Hour Meter is a versatile IoT controller and runtime meter designed to monitor and record the runtime hours of up to two different pieces of equipment. With its digital and analog inputs, and relay outputs, it offers various triggering and notification options. The device can be easily integrated into existing equipment to track usage and maintenance intervals. The WiFi connectivity enables remote monitoring and data collection, allowing you to access runtime information and manage your equipment efficiently.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents