Hoshizaki HS-5462 User manual

Brand: Hoshizaki

Model: HS-5462

Type: User manual

Hoshizaki HS-5462 is an optional heated overflow drain pan kit designed for Steelheart Refrigerator Series Upright models. It helps prevent water damage by collecting and safely draining excess water from the refrigerator. The kit includes a heated overflow drain pan, bracket, drain elbows, vinyl hoses, wire harness, self-drilling hex screws, nylon tie mounts, nylon ties, wire clamp, bushing, junction box, and wiring label. It can be installed on 1-section, 2-section, and 3-section refrigerators. The heated overflow drain pan has a power cord that connects to the refrigerator's power supply.

2A9185-011

Hoshizaki Optional Heated Overow Drain Pan Kit

HS-5462

For Use with Steelheart Refrigerator Series Upright Models

Installation Instructions

Check to ensure that all parts are included:

Index

No. Description

Part

Number Qty

1 Heated Overow Drain Pan 3B0185-01 1

2 Heated Overow Drain Pan Bracket 3B0247-01 1

3 Drain Elbow (1 and 2) 4A1017-01 2

4 Vinyl Hose A (15 1/8 in. (385 mm)) 7725-1923 1

5 Vinyl Hose B (68 in. (1727 mm)) 7725-1923 1

6 Wire Harness (8 ft. (2 m)) 4A6586-01 1

7 Self-Drilling Hex Screw 7B03I1210 8

8 Nylon Tie Mount 437618-01 8

9 Nylon Tie 8911-0200 8

10 Wire Clamp 4A0809-03 1

11 Bushing 428394-01 2

12 Junction Box 3B0361-01 1

13 Wiring Label 3B0115-01 1

WARNING

• The appliance should be serviced only by qualied service personnel to reduce the risk of death, electric

shock, serious injury, or re.

• No installation or service should be undertaken until the technician has thoroughly read these instructions.

Failure to follow these instructions will adversely affect safety, performance, component life and warranty

coverage, and may result in costly water damage.

• To reduce the risk of electric shock, do not touch the plug with damp hands. Move the power switch to the

"OFF" position, then unplug the appliance from the electrical outlet before servicing.

Installation Instructions - Repeat these instructions for second kit on 3-section models

1) Unplug the appliance from the electrical outlet.

2) Move the appliance out to access the rear of the appliance.

3) Remove the front, control, right side, and top panels from the appliance. See Fig. 1.

4) Remove the nylon tie connecting the existing drain hose to the evaporator drain pipe. Remove the existing drain hose and discard.

See Fig. 2.

Fig. 1

Model Shown: R1A-FS

Top Panel

Right

Side Panel

Existing

Drain Hose

Nylon Tie

Fig. 2

Front Panel

Control Panel

Evaporator

Drain Pipe

2A9185-011

6) Connect one end of vinyl hose A (15-1/8 in. (385 mm)) provided in this kit, to the open end of drain elbow 1 and route it to the

back of the appliance under the channel cover. See Fig. 4.

7) Connect one end of the 2nd elbow provided in this kit, to the open end of vinyl hose A

(15-1/8 in. (385 mm)). See Fig. 4.

NOTICE! Be sure drain elbow 2 is properly positioned on vinyl hose A

(15-1/8 in. (385 mm)).

8) Place the heated overow drain pan provided in this kit, into the heated overow drain pan bracket provided in this kit. See Fig. 5.

Fig. 4

Channel Cover

Fig. 5

Heated Overow

Drain Pan Assembly

Heated Overow Drain

Pan Bracket

Fig. 3

Drain Elbow 1

Evaporator Drain Pipe

5) Connect one end of a drain elbow provided in this kit, to the evaporator drain pipe. See Fig. 3. NOTICE! Be sure drain elbow 1 is

properly positioned on the evaporator drain pipe.

Rear

Front

Heated Overow

Drain Pan

Front

Rear

Model Shown: R1A-FS

Heated Overow Drain

Pan Power Cord

Heated Overow Drain

Pan Power Cord

Model Shown: R1A-FS

Vinyl Hose A

Evaporator Drain Pipe

Drain Elbow 1

Drain Elbow 2

Evaporator Drain Pipe

Drain Pan Heater

2A9185-011

15-3/4 in.

(400 mm)

12-7/8 in.

(327 mm)

2 in.

(51 mm)

9) Mount the heated overow drain pan assembly.

1-Section and 3-Section: From the rear of the appliance, measure from the right side (and from the left side for 3-section models)

of the appliance 13-3/4 in. (349mm) and up from the bottom 1-3/4 in. (44 mm) to 2 in. (51 mm) and place a mark. See Fig. 6.

Next, place the heated overow drain pan assembly at the rear and beneath the appliance, ush to the bottom, and with the center

mounting hole lined up to the mark made. See Fig. 6. Lift the heated overow drain pan assembly ush against the rear panel of the

appliance and secure using 4of the self-drilling hex screws provided in this kit. The heated overow drain pan power cord should be

on the left side from the rear view.

Fig. 6

2 in.

(51 mm)

Self-Drilling

Hex Screws

Heated Overow Drain

Pan Power Cord

Heated Overow Drain Pan Assembly

Model Shown: R1A-FS

Place Mark on 1 and 3-Section Here

Fig. 7

Self-Drilling

Hex Screws

Heated Overow Drain

Pan Power Cord

Heated Overow Drain Pan Assembly

Model Shown: R2A-FS

Place Mark on 2-Section Here

2-Section: From the rear of the appliance, measure from the left side of the appliance 15-3/4 in. (400 mm) and up from the bottom

1-3/4 in. (44 mm) to 2 in. (51 mm) and place a mark. See Fig. 7. Next, place the heated overow drain pan assembly at the rear and

beneath the appliance, ush to the bottom, and with the center mounting hole lined up to the mark made. See Fig. 7. Lift the heated

overow drain pan assembly ush against the rear panel of the appliance and secure using 4of the self-drilling hex screws provided

in this kit. The heated overow drain pan power cord should be on the left side from the rear view.

10) Connect one end vinyl hose B (68 in. (1727 mm)) to the open end of drain elbow 2. See Fig. 8. Place the other end of vinyl hoseB

(68 in. (1727 mm)) into the heated overow drain pan assembly as shown in Fig. 9. NOTICE! Be sure vinyl hose B is properly

positioned on drain elbow 2.

Fig. 8

Fig. 9

Model Shown: R1A-FS

Vinyl Hose B

Drain Elbow 2

Heated Overow Drain Pan Assembly

Vinyl Hose A

Vinyl Hose B

2A9185-011

11) Route vinyl hose B as straight as possible down the back of the appliance. Next, mark then drill three 1/4 in. holes for the nylon tie

mounts. See Fig. 10. NOTICE! Do not drill deeper than 1 in. (25 mm). Drilling deeper could penetrate the interior cabinet wall.

12) Insert a nylon tie mount provided with this kit, into each hole drilled in step 11.

13) Route one end of a nylon tie provided with this kit, into each of the nylon tie mounts. Wrap the nylon ties around vinyl hose B. Do not

tighten at this time.

14) Remove vinyl hose B from the heated overow drain pan. Conrm there are no kinks in vinyl hose B, then measure vinyl hose B so

that vinyl hose B extends a minimum of 1 in. (25 mm) into the heated overow drain pan but not deep enough to touch the bottom

of the heated overow drain pan or the heating element. Once the correct amount of hose length is determined, mark the distance

needed and cut vinyl hoseB to that length.

15) Tighten the nylon ties around vinyl hose B. Be sure not to over tighten or pinch vinyl hose B.

Fig. 10

Model Shown: R1A-FS

Heated Overow Drain Pan

Drain Elbow 2

Nylon Tie Mount

1/4 in. Drilled

Holes

Heated Overow Drain

Pan Power Cord

Vinyl

Hose B

Drain Elbow 2

Vinyl Hose B

Nylon Tie

Heated Overow Drain

Pan Power Cord

Fig. 12

Fig. 11

16) Locate the labeled "Drain Pan Heater" wires located in the front area of the appliance. Once located, remove the factory wire

connector caps and plug the wire harness wires provided in this kit, into the "Drain Pan Heater" wires. See Fig. 11. Connect the wire

harness ground (GND) wire to the grounding screw on top of the cabinet. See Fig. 11. NOTICE! Ground wire must be connected

and secure.

17) Route the wire harness from the front of the appliance, between the condenser and evaporator case, over vinyl hose A, and through

the opening under the channel cover (if applicable). See Fig. 12.

Model Shown: R1A-FS

Wire Harness

and Routing

Vinyl Hose A

Drain Elbow 1

Wire Harness

Power Wires

Wire Harness

Ground Wire

Drain Pan Heater

Power Wires

Drain Pan Heater

Power Wires

2A9185-011

Heated Overow Drain Pan

19) Place 1 bushing provided in this kit, on the wire harness and the other bushing on the heated overow drain pan power cord.

Next, place the connection between the heated overow drain pan power cord and the wire harness female connector in the junction

box provided in this kit, then snap the bushings into the top and bottom openings of the junction box.

20) Raise the junction box until the overow drain pan power cord is tight with no slack, then place against the appliance no less than

2 in. (51 mm) from the side of the appliance.

21) Level the junction box, then secure to the appliance using the self-drilling hex screws provided in this kit. See Fig. 14.

22) Route the excess wire harness wire from the junction box to the front area of the appliance. Coil the excess wire harness wires, then

secure with nylon tie. Be sure wire harness wires are clear of moving objects.

23) Secure the heated overow drain pan power supply cord to the appliance, using the self-drilling hex screw and wire clamp provided

in this kit. See Fig. 14. Notice! Conrm the overow drain pan power cord and the wire harness are free of obstructions.

Fig. 13

Model Shown: R1A-FS

Heated Overow Drain

Pan Power Cord

Wire Harness

Wire Harness Cap

Wire Harness

and Heated

Overow Drain

Pan Power Cord

Connection

Wire Harness

Vinyl Hose B

Drain Elbow 2

18) Continue routing the wire harness down the back of the appliance. Next, remove the wire harness cap from wire harness female

connector, then plug the heated overow drain pan power cord into the wire harness female connector. See Fig. 13.

Heated Overow Drain

Pan Power Cord

Junction

Box

Self-Drilling

Hex Screws

Bushings

Fig. 14

Wire

Harness

2 in. min.

(51 mm)

Heated Overow Drain

Pan Power Cord

Wire Harness

Wire Clamp

Self-Drilling

Hex Screw

Model Shown: R1A-FS

Junction

Box

2A9185-011

24) Place three marks as shown in Fig. 15, then drill three 1/4 in. holes for the nylon tie mounts. NOTICE! Do not drill deeper than 1 in.

(25 mm). Drilling deeper could penetrate the interior cabinet wall.

25) Insert a nylon tie mount provided with this kit, into each hole drilled in step 24. Next, route one end of a nylon tie provided with this

kit, into each of the nylon tie mounts, then wrap the nylon ties around wire harness and tighten.

26) Replace the panels in their correct positions.

27) Place the wiring label provided with this kit, over the existing wiring label.

28) Move the appliance back to its original position. Ensure that the heated overow drain pan assembly does not make contact with the

back wall or another surface. Plug the appliance into the electrical outlet.

Fig. 15

Model Shown: R1A-FS

Heated Overow Drain Pan

Wire

Harness

Drain Elbow 2

Nylon Tie Mount

1/4 in. Drilled

Holes

Heated Overow Drain

Pan Power Cord

Nylon Tie

Drain Elbow 2

Wire

Harness

Heated Overow Drain

Pan Power Cord

Hoshizaki HS-5462 User manual

Hoshizaki HS-5462 User manual

Hoshizaki HS-5462 User manual

Related papers

Other documents