ADTRAN MX3112 Job Aid

Brand: ADTRAN

Model: MX3112

Type: Job Aid

C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

For more information, refer to the MX3112 System Manual (P/N 61189901L1-1) available online at www.adtran.com.

MX3112

Controller Card

P/N: 1189901L2

CLEI: M3CU180B_ _

MX3112 CONTROLLER CARD

LED STATUS FOR ACTIVE MX3112 CONTROLLER CARD

ACT z Green.............................................. Normal (All OK)

z/z Green/Amber (Alternating)............ Normal and console open

4 Red (Flashing)................................ Card has failed

z Amber ............................................ Software update in progress

z/z Red/Amber (Alternating)............... Card has failed and console open

ALM z Green.............................................. No critical, major, or minor alarms

z Red ................................................. Major or minor alarm in progress

4 Red (Flashing)................................ Critical alarm in progress

DS3 { Off.................................................. Copper (DSX-1) mode selected

z Green.............................................. Normal (DS3 OK)

z Red ................................................. AIS, OOF, RAI, or Idle

4 Red (Flashing)................................ DS3 LOS

4 Red (Flashing once per event) ....... Single/Burst DS3 code violations during

previous second

z/z Red/Green (Alternating) ................ DS2 OOF

z Amber ............................................ In test (locally originated)

4 Amber (Flashing) ........................... In test (remotely originated)

DSX-1 STAT { Off .................................................. All DSX-1 ports are disabled

z Green.............................................. Enabled DSX-1 ports normal (All OK)

z Red ................................................. Non-critical alarm (AIS) on an enabled

DSX-1 port

4 Red (Flashing)................................ LOS on an enabled port

4 Red (Flashing once per event) ....... Single/Burst RX DSX-1 code violations during

previous second

DSX-1 TEST { Off .................................................. No DSX-1 tests in progress

4 Red (Flashing once per event) ....... Single/Burst pattern errors on DSX-1 test

z Amber ............................................ In test (locally originated)

4 Amber (Flashing) ........................... In test (remotely originated)

ETHERNET 1-4 { Off .................................................. Link not established

z Green.............................................. Link established

LED STATUS FOR STANDBY MX3112 CONTROLLER CARD

ACT 4 Green (Flashing) ............................ Normal (All OK)

z Amber ............................................ Software update in progress

4 Amber (Flashing) ........................... Not ready or software mismatch

4 Red (Flashing)................................ Card failure

ALM { Off .................................................. Permanent state during standby

DS3 { Off .................................................. Permanent state during standby

DSX-1 STAT { Off .................................................. Permanent state during standby

DSX-1 TEST { Off .................................................. Permanent state during standby

ETHERNET 1-4 { Off .................................................. Permanent state during standby

FRONT PANEL SWITCH

ACO Depress to disable any audible alarms only. Any active visual alarms will remain active.

DESCRIPTION

The ADTRAN

MX3112 Controller Card is a plug-in unit for the MX3 Chassis (P/N 1189001L1) that

provides two application modes, Copper mode and DS3 mode. In Copper mode, the MX3112 provides

twelve DS1 ports that can be bonded for transporting the traffic of up to four client Ethernet ports. In DS3

mode, sixteen of the DS3 tributaries can be bonded for transporting the traffic of up to four client Ethernet

ports. Features of the MX3112 Controller Card include:

♦ 1:1 redundancy

♦ Hot-swappable

♦ NEBS Level 3 compliant

The MX3112 Controller Card requires the following modules to be installed in the MX3 Chassis:

♦ MX3 4-Port 10/100Base-T Ethernet Module (P/N 1189902L1) must be installed in module slot

A (lower

slot)

♦ MX3 Fan Module (P/N 1189007L1)

INSTALLATION AND TURNUP

Ensure all MX3 Chassis wiring has been completed. The MX3112 Controller Card uses the following MX3

rear panel connections:

♦

BNC IN/OUT A for DS3

♦

T/R (IN)/(OUT) amphenol connectors, pins 1-12 and 33-44 for DSX-1 ports 1-12

♦

AUX INPUTS 1-8 for Auxiliary Alarms 1-4; pins sense open and closed relay contacts and are not polarity

sensitive

♦

ALARM CONTACTS for critical, major, and minor alarms

NOTE: For the second and third bulleted items above, see the tables in the Pin Assignments section on the

reverse page.

After unpacking the unit, inspect it for damage. If damage has occurred, file a claim with the carrier and then

contact ADTRAN Customer Service. For more information, refer to the warranty.

This module occupies a controller card slot in the MX3 Chassis. Follow the steps listed below to install the

MX3112 Controller Card.

1. If installed, remove the Blank Plug (P/N 1189005L1) from the controller card slot.

WARNING: For configurations utilizing a single MX3112 Controller Card, a Blank Plug must be

installed in the the empty controller card slot.

2. Pull the ejector latches at the left and right sides of the MX3112 Controller Card front panel from their

latched or closed positions.

3. Gently, but firmly, slide the MX3112 Controller Card into the upper or lower controller card slot taking

note of the left and right guide grooves in the chassis. Simultaneously, apply thumb pressure at the left

(on the ADTRAN logo) and right (on the part number) of the MX3112 Controller Card to ensure a good

seat of the MX3112 Controller Card pins into the backplane connector.

4. Push the ejector latches to the left/right against the front panel until engaged.

The MX3112 Controller Card initializes and begins a self-test upon insertion into an active MX3 Chassis.

When the self-test completes, the LEDs reflect the true state of the MX3112 Controller Card.

61189901L2-22B

0705

MX3112 Controller Card

MX3 4-Port Ethernet ModuleMX3 Fan Module

*61189901L2-22B*

PRICING AND AVAILABILITY 800.827.0807

TECH SUPPORT 800.726.8663

RETURN FOR REPAIR 256.963.8722

www.adtran.com

61189901L2-22B

Warranty: ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service.

Warranty information can be found online at www.adtran.com/warranty

MX3112 CONTROLLER CARD

CONNECT AND LOGON

♦ Use the front panel RS-232 DB-9 connector on the active MX3112 Controller Card to provision the

MX3112 system via a VT100 terminal or VT100 terminal emulation software such as HyperTerminal.

♦ Provision the terminal port as follows:

♦ Data Rate: any up to 115200 bps

♦ Asynchronous Data Format: eight data bits, no parity (none), one stop bit, and no flow control

♦ The default username is ADMIN and default password is PASSWORD (both are uppercase)

PIN ASSIGNMENTS

WARNING: The DS3, Alarm, DSX-1, and Ethernet interfaces MUST NOT be metallically connected to

interfaces that connect to the Outside Plant (OSP) or its wiring. These interfaces are

designed for use as intra-building interfaces only. The addition of primary protectors is not

sufficient protection in order to connect these interfaces metallically to OSP wiring.

OPERATIONAL SPECIFICATIONS

QUICK SETUP MENU

To simplify the installation process, all of the basic configuration options necessary to get the MX3112

running are grouped together on the Quick Setup menu.

After installing the unit and successfully logging on, the MX3112 Main menu appears. From the Main menu,

select

Quick Setup, and press ENTER.

The Quick Setup screen allows configuration of such items as application mode, DS1 bonding assignments,

Ethernet client port configuration, as well as, system date, time, and IP address information.

T/R (IN)/(OUT) Amp Connector Pin List Aux Inputs 1 - 8 Pin List

Pin Function Pin Aux Inputs Function

1 Ring 1 Tip 1 33 1, 2 Alarm 1

2 Ring 2 Tip 2 34 3, 4 Alarm 2

3 Ring 3 Tip 3 35 5, 6 Alarm 3

4 Ring 4 Tip 4 36 7, 8 Alarm 4

5 Ring 5 Tip 5 37

6 Ring 6 Tip 6 38

7 Ring 7 Tip 7 39

8 Ring 8 Tip 8 40

9 Ring 9 Tip 9 41

10 Ring 10 Tip 10 42

11 Ring 11 Tip 11 43

12 Ring 12 Tip 12 44

32 FGND FGND 64

Specification Description

Input Voltage –48 VDC Systems: –42 VDC to –60 VDC

–24 VDC Systems: –22 VDC to –27 VDC

+24 VDC Systems: +22 VDC to +27 VDC

Temperature Operation: –40°C to +65°C

Storage: –40°C to +85°C

Relative Humidity Up to 95% noncondensing

MAPPING AND BONDING GROUP ASSIGNMENTS

COMPLIANCE

Refer to the MX3112 Controller Card Compliance Notice (P/N 61189901L2-17) for detailed

compliance information.

DS3 Mode

DS3

Tributary

Assignment

DS3

Tributary

Assignment

DS3

Tributary

Assignment

1 DSX-1 Port 1 13 User Assigned Bonding Group 25 User Assigned Bonding Group

2 DSX-1 Port 2 14 User Assigned Bonding Group 26 User Assigned Bonding Group

3 DSX-1 Port 3 15 User Assigned Bonding Group 27 User Assigned Bonding Group

4 DSX-1 Port 4 16 User Assigned Bonding Group 28 User Assigned Bonding Group

5 DSX-1 Port 5 17 User Assigned Bonding Group

6 DSX-1 Port 6 18 User Assigned Bonding Group

7 DSX-1 Port 7 19 User Assigned Bonding Group

8 DSX-1 Port 8 20 User Assigned Bonding Group

9 DSX-1 Port 9 21 User Assigned Bonding Group

10 DSX-1 Port 10 22 User Assigned Bonding Group

11 DSX-1 Port 11 23 User Assigned Bonding Group

12 DSX-1 Port 12 24 User Assigned Bonding Group

Copper Mode

DS1 Port Assignment

1 User Assigned Bonding Group

2 User Assigned Bonding Group

3 User Assigned Bonding Group

4 User Assigned Bonding Group

5 User Assigned Bonding Group

6 User Assigned Bonding Group

7 User Assigned Bonding Group

8 User Assigned Bonding Group

9 User Assigned Bonding Group

10 User Assigned Bonding Group

11 User Assigned Bonding Group

12 User Assigned Bonding Group

ADTRAN MX3112 Job Aid

ADTRAN MX3112 Job Aid

Related papers

Other documents