Aries 3044 Installation guide

Aries
Brand
Aries
Model
3044
Type
Installation guide

Aries 3044 will spruce up your 1998-2000 Ford Ranger & Mazda B-Series Pickups while providing essential protection. Here is a concise overview of its capabilities:

  • Front-end protection: Shield your pickup's front end from minor impacts and off-road hazards with this sturdy grill guard.

  • Easy installation: Follow the included instructions for a straightforward installation process using the provided mounting hardware.

  • Durable construction: Made from high-quality materials, this grill guard is built to withstand the rigors of daily use and outdoor elements.

  • Enhanced aesthetics: Upgrade the appearance of your pickup with the sleek and rugged design of the Aries 3044 grill guard.

Aries 3044 will spruce up your 1998-2000 Ford Ranger & Mazda B-Series Pickups while providing essential protection. Here is a concise overview of its capabilities:

  • Front-end protection: Shield your pickup's front end from minor impacts and off-road hazards with this sturdy grill guard.

  • Easy installation: Follow the included instructions for a straightforward installation process using the provided mounting hardware.

  • Durable construction: Made from high-quality materials, this grill guard is built to withstand the rigors of daily use and outdoor elements.

  • Enhanced aesthetics: Upgrade the appearance of your pickup with the sleek and rugged design of the Aries 3044 grill guard.

PARTS LIST:
Qty Description Qty Description
1 Grill Guard 2 12mm Lock Nuts
1 Driver/Left Upper Brace Bracket (Ranger) 4 12mm ID x 35mm OD Flat Washers
1 Passenger/Right Upper Brace Mounting Bracket (Ranger) 2 10mm x 30mm Hex Bolts
1 Driver/Left Upper Brace Bracket (Mazda) 2 10mm Lock Nuts
1 Passenger/Right Upper Brace Bracket (Mazda) 4 10mm ID x 27mm OD Flat Washers
2 12mm x 100mm Hex Bolts
Drive
r
/
Left Side
Brace Bracket
Mazda only
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. From underneath vehicle locate the existing slotted holes in both side of the frame just behind
the bumper, with assistance attach the grill guard to the inner side of frame using the 12mm x
100mm Hex bolts, 12mm flat washers & the 12mm lock nuts (Note; due to variances in
plastic below bumper some models may need trimming or notching of the plastic to
allow for adjustment of grill guard.) Snug hardware, but do not tighten hardware at this time.
3. Locate the factory bolts which are near the top back side of front bumper, these can be
accessed from either reaching through the gap between the bottom of the grill and the top of
bumper or from the underneath, depending on the space available, remove these factory bolts
and attach upper brace brackets for your vehicle type (refer to diagram below for bracket
selection of vehicle type driver & passenger sides) secure these brackets with the factory
bolts. Snug but do not tighten hardware at this time. Secure the other ends of brackets to the
grill guard with the 10mm fasteners, Snug hardware, but do not tighten hardware at this time.
4. Once all hardware is installed align your grill guard to vehicle, and tighten all hardware,
Do periodic inspections to the installation to make sure all hardware is secure and tight.
Page 1 of 2 4/8/2011
INSTALLATION INSTRUCTIONS
1998-2000 Ford Ranger & Mazda B-Series Pickups
Part 3044 / 3044-2
Passenge
r
/
Right
Side Brace Bracket
Ranger only
Drive
r
/
Left Side
Brace Bracket
Ranger only
Passenge
r
/
Right
Side Brace Bracket
Mazda only
To protect your investment, wax this product after installing. Regular waxing is recommended to
add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives
that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish.
Mild soap may be used also to clean the Product.
For gloss black finishes: Mild soap may be used to clean the Product.
Page 2 of 2 4/8/2011
Secure to frame with
(1) 12mm x 100mm Hex bolt
(2) 12mm flat washers
(1) 12mm Lock nut
Driver side shown
U
pp
er Brace bracket Passen
g
er side
(
Ran
g
er Onl
y)
Upper Brace bracket
Driver side (Mazda Only)
Installs to inside of grill
guard
Frame
Secure to grill guard with
(1) 10mm x 30mm Hex bolt
(2) 10mm flat washers
(1) 10mm Lock nut
  • Page 1 1
  • Page 2 2

Aries 3044 Installation guide

Aries
Brand
Aries
Model
3044
Type
Installation guide

Aries 3044 will spruce up your 1998-2000 Ford Ranger & Mazda B-Series Pickups while providing essential protection. Here is a concise overview of its capabilities:

  • Front-end protection: Shield your pickup's front end from minor impacts and off-road hazards with this sturdy grill guard.

  • Easy installation: Follow the included instructions for a straightforward installation process using the provided mounting hardware.

  • Durable construction: Made from high-quality materials, this grill guard is built to withstand the rigors of daily use and outdoor elements.

  • Enhanced aesthetics: Upgrade the appearance of your pickup with the sleek and rugged design of the Aries 3044 grill guard.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents