Equinox Systems EQLED162 User Manuals

Equinox Systems
Brand
Equinox Systems
Model
EQLED162
Category
Stroboscopes & disco lights
Type
User Manuals

This manual is also suitable for

Order codes:
EQLED162 - Black Housing
EQLED162A - White Housing
Maxi Batt
User Manual
www.prolight.co.uk Maxi Batt User Manual
2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CARE-
FULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablemainssupplyvoltageis
between100~240VAC,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.
• Thisunitisnotintendedforxedinstallation.
• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• Thislightingxtureisforprofessionaluseonly-itis
notdesignedfororsuitableforhouseholduse.The
productmustbeinstalledbyaqualiedtechnicianin
accordancewithlocalterritoryregulations.Thesafetyof
theinstallationistheresponsibilityoftheinstaller.The
xturepresentsrisksofsevereinjuryordeathduetore
hazards,electricshockandfalls.
• Warning!RiskGroup2LEDproductaccordingto
EN62471.Donotviewthelightoutputwithoptical
instrumentsoranydevicethatmayconcentratethebeam.
• WARRANTY:Oneyearfromdateofpurchase.
www.prolight.co.uk Maxi Batt User Manual
3
Product overview & technical specications
RechargeablelithiumbatterypoweredLEDParcansutilising1WRGBW
LEDsforstageorwallwashing.Withnocablestoconnectyouarefree
tosetupthextureswhereveryouwant.Theinternalbatterywillkeepa
chargeforupto4hours(fullon)fromasinglecharge.Functionoptions
andDMXaddressingcanbechangedusingthe4buttonLEDdisplayor
controlledbythesuppliedIRremotecontrol.
•24x1WLEDs(R:6,G:6,B:6,W:6)
•Beamangle:25°
•1,102Lux@2m(fullon)
•DMXchannels:5or8selectable
•Staticcolour,colourchange,colour
fade,auto,soundactiveandmaster/
slavemodes
•0-100%dimmingandvariablestrobe
•4pushbuttonmenuwithLEDdisplay
•Bracketallowsformultipleriggingor
oorstandingapplications
•Rechargeablebattery
forwirelessapplications
•Maximumruntime:
6hours(singlecolour)
•Chargingtime:5hours(max.)
•DC12Vcharginginput
(viatheincludedcharger)
•3-PinXLRinput/output
•Fancooled
Maxi Batt
Specications Maxi Batt
Powerconsumption 30W
Powersupply 100~240V,50/60Hz
Battery 12V4400mAh
Dimensions 230x200x155mm
Weight 1.1kg
Ordercode EQLED162-Blackhousing
EQLED162A-Whitehousing
0m 1m 2m 3m 4m 5m
25° - Lux
FULL ON
R
G
B
W
4400
824
2140
274
1360
1102
206
535
68.4
341
489
91.6
238
30.4
152
25°
275
51.5
134
17.1
85.3
176
33
85.6
10.9
54.6
200mm
230mm
155mm
*WARNING!Charginginputonly
viatheapprovedchargersupplied.
Thismustnotbeusedwitha
standardDCpowersupply.
MODE
DMX IN DMX OUT
POWER
UP DOWN ENTER
08
09
MODE
DMX IN DMX OUT
POWER
UP DOWN ENTER
02 02
01 01
03
07
06 04
05
01-Bracket
02-Brackettighteningknobs
03-LEDdisplay
04-Functionbuttons
05-Microphone
06-3-PinDMXinput
07-3-PinDMXoutput
08-On/offbutton
09-12VDCcharginginput*
Inthebox:
1 x xture, 1 x charger
& 1 x user manual
www.prolight.co.uk Maxi Batt User Manual
4
Operating instructionsOperating instructions
MENU
C F 0 1
Colour fade mode 1
C F 0 1
C F 9 9
C J 0 1
Colour change mode
C J 0 1
C J 9 9
C P 0 1
Colour fade mode 2
C P 0 1
C P 9 9
C t 0 1
Strobe mode
C t 0 1
C t 9 9
Slave mode
S L A u
Auto mode
d E n o
Sound active mode
S o u d
r G b
g. 0 0 0
r. 2 5 5
r. 0 0 0
g. 2 5 5
b. 0 0 0
b. 2 5 5
y. 0 0 0
y. 2 5 5
Manual dimming mode
A 0 0 1
DMX address & channel settings (8CH mode)
A 0 0 1
A 5 1 1
d 0 0 1
DMX address & channel settings (5CH mode)
d 0 0 1
d 5 1 1
www.prolight.co.uk Maxi Batt User Manual
5
Operating instructions
DMX mode:
OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomes
tocustomisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitof
thextureandeachxtureindependently.
ToaccesstheDMXaddressandchannelmodefor5channelDMX,pressthe“MENU”buttonontherear
oftheunittoshowd001ontheLEDdisplay.Thisisnowin5channelmode.Nowpressthe“ENTER”
buttonandusethe“UP”and“DOWN”buttonstosettherequiredDMXaddress.Pressthe“ENTER”
buttontoconrmthesetting.Pressthe“ENTER”buttontoconrmthesetting.
ToaccesstheDMXaddressandchannelmodefor8channelDMX,pressthe“MENU”buttonontherear
oftheunittoshowA001ontheLEDdisplay.Thisisnowin8channelmode.Nowpressthe“ENTER”
buttonandusethe“UP”and“DOWN”buttonstosettherequiredDMXaddress.Pressthe“ENTER”
buttontoconrmthesetting.Pressthe“ENTER”buttontoconrmthesetting.
8 channel mode:
Channel Value Function
CH1 000-255 Masterdimmer(0-100%)
CH2 000-255 Red(0-100%)
CH3 000-255 Green(0-100%)
CH4 000-255 Blue(0-100%)
CH5 000-255 White(0-100%)
CH6 000-255
Automode(slow-fast)(CH1-5
mustbeusedwiththischannel)
CH7 000-255
Strobemode(slow-fast)(CH1-5
mustbeusedwiththischannel)
CH8
000-050 Nofunction
051-100 Staticcolours
101-199 Colourfade(slow-fast)
200-250 Colourchange(slow-fast)
251-255 Soundactive
5 channel mode:
Channel Value Function
CH1 000-255 Masterdimmer(0-100%)
CH2 000-255 Red(0-100%)
CH3 000-255 Green(0-100%)
CH4 000-255 Blue(0-100%)
CH5 000-255 White(0-100%)
www.prolight.co.uk Maxi Batt User Manual
6
Colour fade mode 1:
Toaccesscolourfademode1,pressthe“MENU”buttonontherearoftheunittoshowCF01
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
speedbetweenCF01~CF99.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Value: 01 - 99 (01 = slow speed, 99 = fast speed)
Colour change mode:
Toaccesscolourchangemode,pressthe“MENU”buttonontherearoftheunittoshowCJ01
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
speedbetweenCJ01~CJ99.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Value: 01 - 99 (01 = slow speed, 99 = fast speed)
Colour fade mode 2:
Toaccesscolourfademode2,pressthe“MENU”buttonontherearoftheunittoshowCP01
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
speedbetweenCP01~CP99.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Value: 01 - 99 (01 = slow speed, 99 = fast speed)
Strobe mode:
Toaccessstrobemode,pressthe“MENU”buttonontherearoftheunittoshowCt01
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
speedbetweenCt01~Ct99.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Value: 01 - 99 (01 = slow speed, 99 = fast speed)
Manual dimming mode:
Toaccessthemanualdimmingmode,pressthe“MENU”buttonuntilthedisplayshowsrGbonthe
LEDdisplay.Usethe“UP”and“DOWN”buttonstoselecttherequiredbrightnessofredfromr.000~
r.255.Pressthe“ENTER” buttonfollowedbythe“MENU”buttonandrepeatforg(green),b(blue)
andy(white).Pressthe“ENTER” buttontoconrmthesetting.
Value: 000 - 255 (000 = low brightness, 255 = high brightness)
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
www.prolight.co.uk Maxi Batt User Manual
7
Operating instructions
Master/slave mode:
Tosetthemasterunitselectyourdesiredprogram(colourchange,colourfade,auto,sound
activeorstrobe.Tosettheotherunitsinslavemode,pressthe“MENU”buttononthefrontoftheunitto
showSLAuontheLEDdisplay.Pressthe“ENTER”buttontoconrmthesetting.Theunitwillnowrun
insequencewiththemasterunit.Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.
Auto mode:
Toaccessautomode,pressthe“MENU”buttonontherearoftheunittoshowdEnoontheLED
display.Thexturewillnowrunthroughallitsbuilt-inprograms
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Sound mode:
Toaccesssoundmode,pressthe“MENU”buttonontherearoftheunittoshowSoudontheLED
display.Thexturewillnowruninsoundmode.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
www.prolight.co.uk Maxi Batt User Manual
8
Operating instructions
IR remote functions:
Button functions:
01-Setstheunitintoblackoutonoroff
02-Usetoselectbetween5CH,8CHorSlavemodes
03-Staticcolourmode-Usetoselectoneofthe
presetcolours
04-Automode-Usethisbuttontoselectautomode
05-Colourchangemode-Usethe‘+’and‘-’buttonsto
selectthedesiredspeed
06-Colourfademodes-Pressthistoswitchbetween
Fade1andFade2modes.Usethe‘+’and‘-’
buttonstoselectthedesiredspeed
07-Strobemode-Usethe‘+’and‘-’buttonsto
selectthedesiredspeed
08-Soundactivemode-Usethisbuttontoselectsound
activemode
09-Usethesebuttonstoadjustthespeedofanyofthe
colourchange,colourfadeorstrobeprograms.
–
+
DMX
WHITE
ROSE
RED
ON/OFF ON/OFF
CYAN
BLUE
AMBER
GREEN
SPEED
Sound
Auto
FadeJump Strobe
03
01
04
02
07
06
09
05
08
www.prolight.co.uk Maxi Batt User Manual
9
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Also remember that DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m
www.prolight.co.uk Maxi Batt User Manual
10
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterference.Itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup
www.prolight.co.uk Maxi Batt User Manual
11
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.
www.prolight.co.uk Maxi Batt User Manual
12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Equinox Systems EQLED162 User Manuals

Equinox Systems
Brand
Equinox Systems
Model
EQLED162
Category
Stroboscopes & disco lights
Type
User Manuals
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents