Sistema SMARTCANSPOT65 User manual

SMARTCANSPOT65
Brand
Sistema
Model
SMARTCANSPOT65
Category
Stroboscopes & disco lights
Type
User manual

The Sistema SMARTCANSPOT65 is a versatile and powerful 20W battery-powered LED par light that offers a wide range of features for both professional and home use. With its compact size and lightweight design, it's perfect for mobile DJs, clubs, or even for adding a touch of ambiance to your backyard parties.

The Sistema SMARTCANSPOT65 is a versatile and powerful 20W battery-powered LED par light that offers a wide range of features for both professional and home use. With its compact size and lightweight design, it's perfect for mobile DJs, clubs, or even for adding a touch of ambiance to your backyard parties.

USER MANUAL
Please read over this manual before operating the light
SMARTCANSPOT65
20W Battery Powered PAR LED
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
There are two buttons on the rear panel of the lighting. One is for power, and
the other is fo
r
signal.
●When use the fixture with DMX, not wireless, please switch the signal butt
on for “off”
●When use the wireless DMX, please switch the button for “on”
●When charge the light, please switch both of the button for “of”. At the sam
e time, if the s
witch
for power is “on”, the light will be at work during the process of charge, but wil
l consume so
me
power from the charge; if the switch for power is “off”, the light will be blackou
t and not be a
t
work.
Tip for the battery and charge:
●The battery can last for 4-5 hours when all LEDs on after full charge , and
can last for m
ore
than 6-8 hours on auto running mode. Up to 20 Hours with one color diode on
. Results will
vary
based on brightness of LEDs
●It is suggested to charge the battery for at least 4 hours, which will extend
the life span
of the
battery.
8
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
Most important: FIRST CHARGE THE FIXTURES FOR 6-8 Hours on the First
Charge before use. Plug in Power cord. Turn off Power Switch and Turn off
other switch to charge.
Introduction
Unpacking: Thank you for purchasing this product, all products has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the shipping carton for damage
that may have occurred during shipping. If the carton appears to be damaged, carefully inspect
your fixture for any damage and be sure all accessories necessary to operate the unit has arrived
intact. In the case damage has been found or parts are missing, please contact the manufacturer
or your dealer for further instructions. Do not return this unit to your dealer without first
contacting.
Introduction: this lighting is a DMX intelligent and battery powered LED par light. This par light is
light weight and compact which makes it a great piece for mobile DJ‟s and clubs.
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain
or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself; doing so will void your manufactures warranty. In the unlikely event your unit may
require service please contact the manufacturer or your dealer.
PLEASE recycle the shipping carton whenever possible.
General Instructions
To optimize the performance of this product, please read these operating instructions carefully to
familiarize you with the basic operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please keep this manual with the unit,
for future reference.
1
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
Features
●Power supply: AC110V-250V
●Frequency: 50-60Hz
●Power consumption: 20W
●Light source: 1pcs 20W high brightness 6 in 1 leds
●Lamp life: 6-10 ten thousand hrs
●LED angle: 65 degree
●Color: 16.7 million kinds of color change
●Control channels: 6/10 chs
●Control mode: DMX512, master/slave, auto, sound active
●Automatic model(by function button) : color change, color strobe, color dimmer, color gradual
change/color jump change
●Operation menu: LCD display
●Packing size: 265*140*145mm
●N.W: 1.6kg
●G.W: 1.8kg
Safety Precautions
●To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
●Do not spill water or other liquids into or on to your unit.
●Be sure that the local power outlet match that of the required voltage for your unit.
●Do not attempt to operate this unit if the power cord has been frayed or broken. Do not
attempt to remove or break off the ground prong from the electrical cord. This prong is used to
reduce the risk of electrical shock and fire in case of an internal short.
●Disconnect from main power before making any type of connection.
●Do not remove the cover under any conditions. There are no user serviceable parts inside.
●Never operate this unit when it‟s cover is removed.
●Never plug this unit in to a dimmer pack.
●Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall.
●Do not attempt to operate this unit, if it becomes damaged.
●This unit is intended for indoor use only; use of this product outdoors voids all warranties.
●During long periods of non-use, disconnect the unit‟s main power.
●Always mount this unit in safe and stable matter.
●Power-supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to the point they exit from unit.
●Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See
“Cleaning” for details.
●Heat -The appliance should be situated away from heat sources such as radiators, heat
registers, stoves, or other appliances (including amplifiers) that produce heat.
●The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in
performance
2
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
Infrared function
7
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
For Battery Function and Charge
The unit has the function of battery powered. The button for batt
ery and
charge is set on the rear panel. It is showed as the following pict
ure, and
the function is described as below.
6
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
●Fuse standard is 2A/250V
●Grounded using yellow/green line
●The ambient temperature must always be under +35° C
Set Up
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches
the required voltage for your light is workable in 100-220V/50~60Hz. Because line voltage may
vary from venue to venue, you should be sure your unit voltage matches the wall outlet voltage
before attempting to operate you fixture.
Operating Instructions
Operating Modes: You can use this lighting in 5 ways:
●Sound activation – The unit will activated by the sound signal.
●Static display – The unit will display the color in static way.
●Auto Mode -The unit will automatically chase through the different patterns.
●DMX control mode -This function will allow you to control the lighting with a standard DMX
512 controller.
●Battery powered – This function will allow you to control the lighting independently without
any DMX cable
DMX Mode: Operating through a DMX controller give the user the freedom to create their own
programs tailored to their own individual needs. This function also allows you to use your
fixtures as pattern changing lights.
1. This function will allow you to control each individual fixtures traits with a standard DMX 512
controller.
2. this lighting use 6/10 DMX channels to operate. Please see “DMX channel and Functions” for
the DMX traits.
3. To run your fixture in DMX mode, plug in the fixture via the XLR connections to any standard
DMX controller. Set your desired DMX address following the setup specifications that come with
your DMX controller.
4. The unit can automatically recognize the DMX signal once the DMX connection is done.
DMX Linking:
To ensure proper DMX data transmission, when using several DMX fixtures try to use the
shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a
fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
3
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
6CH Mode
Value
CH1
0
1-255
CH2
0
1-255
CH3
0
1-255
CH4
0
1-255
CH5
0
1-255
CH6
0
1-255
10CH Mode
Value
Description
CH1
0
No action
1-255
RGBCLA dimmer
CH2
0-4
No action
5-255
Strobe from slow to fast
CH3
0
No function
1-255
Red dimmer
CH4
0
No function
1-255
Green dimmer
CH5
0
No function
1-255
Blue dimmer
CH6
0
No function
1-255
Cyan dimmer
CH7
0
No function
1-255
Lemon dimmer
CH8
0
No function
1-255
Amber dimmer
CH9
0-4
No function
5-80
Color macro
81-150
Color jump
151-220
Color fade
221-255
Sound active
CH10
0
No function
1-255
Speed from slow to fast
LCD Operation Menu:
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
6CH Mode
Value
Description
CH1
0
No action
1-255
RED dimmer
CH2
0
No action
1-255
GREEN dimmer
CH3
0
No action
1-255
BLUE dimmer
CH4
0
No action
1-255
Cyan dimmer
CH5
0
No action
1-255
Lemon dimmer
CH6
0
No action
1-255
Amber dimmer
10CH Mode
Value
Description
CH1
0
No action
1-255
RGBCLA dimmer
CH2
0-4
No action
5-255
Strobe from slow to fast
CH3
0
No function
1-255
Red dimmer
CH4
0
No function
1-255
Green dimmer
CH5
0
No function
1-255
Blue dimmer
CH6
0
No function
1-255
Cyan dimmer
CH7
0
No function
1-255
Lemon dimmer
CH8
0
No function
1-255
Amber dimmer
CH9
0-4
No function
5-80
Color macro
81-150
Color jump
151-220
Color fade
221-255
Sound active
CH10
0
No function
1-255
Speed from slow to fast
LCD Operation Menu:
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
For Battery Function and Charge
The unit has the function of battery powered. The button for battery and
charge is set on the rear panel. It is showed as the following picture, and
the function is described as below.
6
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
●Fuse standard is 2A/250V
●Grounded using yellow/green line
●The ambient temperature must always be under +35° C
Set Up
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches
the required voltage for your light is workable in 100-220V/50~60Hz. Because line voltage may
vary from venue to venue, you should be sure your unit voltage matches the wall outlet voltage
before attempting to operate you fixture.
Operating Instructions
Operating Modes: You can use this lighting in 5 ways:
●Sound activation – The unit will activated by the sound signal.
●Static display – The unit will display the color in static way.
●Auto Mode -The unit will automatically chase through the different patterns.
●DMX control mode -This function will allow you to control the lighting with a standard DMX
512 controller.
●Battery powered – This function will allow you to control the lighting independently without
any DMX cable
DMX Mode: Operating through a DMX controller give the user the freedom to create their own
programs tailored to their own individual needs. This function also allows you to use your
fixtures as pattern changing lights.
1. This function will allow you to control each individual fixtures traits with a standard DMX 512
controller.
2. this lighting use 6/10 DMX channels to operate. Please see “DMX channel and Functions” for
the DMX traits.
3. To run your fixture in DMX mode, plug in the fixture via the XLR connections to any standard
DMX controller. Set your desired DMX address following the setup specifications that come with
your DMX controller.
4. The unit can automatically recognize the DMX signal once the DMX connection is done.
DMX Linking:
To ensure proper DMX data transmission, when using several DMX fixtures try to use the
shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a
fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
3
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
Features
●Power supply: AC110V-250V
●Frequency: 50-60Hz
●Power consumption: 20W
●Light source: 1pcs 20W high brightness 6 in 1 leds
●Lamp life: 6-10 ten thousand hrs
●LED angle: 65 degree
●Color: 16.7 million kinds of color change
●Control channels: 6/10 chs
●Control mode: DMX512, master/slave, auto, sound active
●Automatic model(by function button) : color change, color strobe, color dimmer, co
lor gradual
change/color jump change
●Operation menu: LCD display
●Packing size: 265*140*145mm
●N.W: 1.6kg
●G.W: 1.8kg
Safety Precautions
●To reduce the risk of electrical shock or fire, do not expose this unit to rain or mois
ture.
●Do not spill water or other liquids into or on to your unit.
●Be sure that the local power outlet match that of the required voltage for your unit.
●Do not attempt to operate this unit if the power cord has been frayed or broken. D
o not
attempt to remove or break off the ground prong from the electrical cord. This prong i
s used to
reduce the risk of electrical shock and fire in case of an internal short.
●Disconnect from main power before making any type of connection.
●Do not remove the cover under any conditions. There are no user serviceable part
s inside.
●Never operate this unit when it‟s cover is removed.
●Never plug this unit in to a dimmer pack.
●Always be sure to mount this unit in an area that will allow proper ventilation. Allo
w about 6”
(15cm) between this device and a wall.
●Do not attempt to operate this unit, if it becomes damaged.
●This unit is intended for indoor use only; use of this product outdoors voids all war
ranties.
●During long periods of non-use, disconnect the unit‟s main power.
●Always mount this unit in safe and stable matter.
●Power-supply cords should be routed so that they are not likely to be walked on or
pinched by
items placed upon or against them, paying particular attention to the point they exit fr
om unit.
●Cleaning -The fixture should be cleaned only as recommended by the manufactur
er. See
“Cleaning” for details.
●Heat -The appliance should be situated away from heat sources such as radiators
, heat
registers, stoves, or other appliances (including amplifiers) that produce heat.
●The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in
performance
2
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
Infrared function
7
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
There are two buttons on the rear panel of the lighting. One is for power, and the other is for
signal.
●When use the fixture with DMX, not wireless, please switch the signal button for “off”
●When use the wireless DMX, please switch the button for “on”
●When charge the light, please switch both of the button for “of”. At the same time, if the switch
for power is “on”, the light will be at work during the process of charge, but will consume some
power from the charge; if the switch for power is “off”, the light will be blackout and not be at
work.
Tip for the battery and charge:
●The battery can last for 4-5 hours when all LEDs on after full charge , and can last for more
than 6-8 hours on auto running mode. Up to 20 Hours with one color diode on. Results will vary
based on brightness of LEDs
●It is suggested to charge the battery for at least 4 hours, which will extend the life span of the
battery.
8
6 IN 1 BATTERY & WIRELESS WATER PROOF PAR
Most important: FIRST CHARGE THE FIXTURES FOR 6-8 Hours on the First
Charge before use. Plug in Power cord. Turn off Power Switch and Turn off
other switch to charge.
Introduction
Unpacking: Thank you for purchasing this product, all products has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the shipping carton for damage
that may have occurred during shipping. If the carton appears to be damaged, carefully inspect
your fixture for any damage and be sure all accessories necessary to operate the unit has arrived
intact. In the case damage has been found or parts are missing, please contact the manufacturer
or your dealer for further instructions. Do not return this unit to your dealer without first
contacting.
Introduction: this lighting is a DMX intelligent and battery powered LED par light. This par light is
light weight and compact which makes it a great piece for mobile DJ‟s and clubs.
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain
or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself; doing so will void your manufactures warranty. In the unlikely event your unit may
require service please contact the manufacturer or your dealer.
PLEASE recycle the shipping carton whenever possible.
General Instructions
To optimize the performance of this product, please read these operating instructions carefully to
familiarize you with the basic operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please keep this manual with the unit,
for future reference.
1
6 in 1 BATTERY POWERED & WIRELESS
DMX WATER PROOF PAR
USER MANUAL
Please read over this manual before operating the light
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Sistema SMARTCANSPOT65 User manual

SMARTCANSPOT65
Brand
Sistema
Model
SMARTCANSPOT65
Category
Stroboscopes & disco lights
Type
User manual

The Sistema SMARTCANSPOT65 is a versatile and powerful 20W battery-powered LED par light that offers a wide range of features for both professional and home use. With its compact size and lightweight design, it's perfect for mobile DJs, clubs, or even for adding a touch of ambiance to your backyard parties.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents