Dunlop JP95 User manual

Dunlop
Brand
Dunlop
Model
JP95
Category
Coaxial cables
Type
User manual

Dunlop JP95 is a signature Cry Baby Wah pedal with a variety of features that make it a versatile tool for guitarists of all levels. It offers precise control over the wah effect, with internal EQ controls that allow you to boost or cut specific frequencies, as well as a Q adjustment to control the width of the wah bandpass. The JP95 also has a volume control to adjust the overall output level, making it easy to integrate into your rig.

Dunlop JP95 is a signature Cry Baby Wah pedal with a variety of features that make it a versatile tool for guitarists of all levels. It offers precise control over the wah effect, with internal EQ controls that allow you to boost or cut specific frequencies, as well as a Q adjustment to control the width of the wah bandpass. The JP95 also has a volume control to adjust the overall output level, making it easy to integrate into your rig.

THE ORIGINAL SINCE 1967.
92503019541REVA
JP95 JOHN PETRUCCI CRY BABY
®
WAH
POWER
The John Petrucci Signature Cry Baby Wah
is powered by one 9-volt battery (accessed
via bottom of pedal), an AC adapter such
as the Dunlop ECB003/ECB003EU, or the
DC Brick
™
and Iso-Brick
™
power supplies.
INTERNAL CONTROLS
Q ADJ trimpot adjusts width of
JP95’s bandpass
VOLUME trimpot sets overall
effect volume
EQ trimpots boost or cut indicated
frequency (100Hz–3.2Khz)
JOHN PETRUCCI’S SETTINGS
SETUP INSTRUCTIONS
• Run an instrument cable from your
guitar to the JP95’s INSTRUMENT jack
and another instrument cable from
the JP95’s AMPLIFIER jack to your
amplifier’s input.
• To turn the pedal on/off, push the toe of
the pedal down until you feel a “click.”
• The JP95 ships with John Petrucci’s
control settings by default (see JOHN
PETRUCCI’S SETTINGS). Use a trimpot
adjustment tool to change the settings to
your own preference.
• Rotate VOLUME control clockwise
to increase effect volume or
counterclockwise to decrease it.
• Rotate Q ADJ control clockwise for a
narrower bandpass to emphasize higher
end harmonics or counterclockwise for
a wider bandpass that emphasizes lower
end harmonics.
• The six internal EQ controls—labeled
from 100Hz to 3.2Khz—can be used to
boost or cut the indicated frequency by
+/-18 dBV. Rotate clockwise to boost or
counterclockwise to cut.
• Rock your foot back and forth on the
pedal to hear the vocal, expressive tones
that the Cry Baby Wah is famous for.
Note: Internal TEST/NORM switch is for
production testing only. Always leave
it set to the NORM position for full
functionality of all controls.
DUNLOP MANUFACTURING, INC.
P.O. BOX 846, BENICIA, CA 94510 U.S.A.
TEL: 1-707-745-2722 FAX: 1-707-745-2658
100Hz
VOLUME
200Hz 400Hz 800Hz 1.6Khz 3.2Khz
Q ADJ
SPECIFICATIONS
Filter Parameter
Heel Down Low Pass 200Hz - 240Hz
Toe Down High Pass 1.2KHz - 1.5KHz
Nominal Input -8 dBV
Max Output +6 dBV
Noise Floor* < -94 dBV
Input Impedance 800K Ω
Output Impedance 5K Ω
Output Gain
Toe Down +33 dBV
Heel Down +19 dBV
Bypass Configuration True Hardwire
Power Requirements 13mA @ 9VDC
*A weighted
  • Page 1 1
  • Page 2 2

Dunlop JP95 User manual

Dunlop
Brand
Dunlop
Model
JP95
Category
Coaxial cables
Type
User manual

Dunlop JP95 is a signature Cry Baby Wah pedal with a variety of features that make it a versatile tool for guitarists of all levels. It offers precise control over the wah effect, with internal EQ controls that allow you to boost or cut specific frequencies, as well as a Q adjustment to control the width of the wah bandpass. The JP95 also has a volume control to adjust the overall output level, making it easy to integrate into your rig.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents