EXPLANATION OF OPERATION PANEL
1. ELECTRONIC HUMIDISTAT
for continuous adjustment of the desired humidity. The
optimum value between 40% and 60% is easy to adjust. You
press the button
11
and
12
together and after some seconds
on the LCD display the current value of humidity starts to flash.
Now it is possible to adjust with the button
12
or with the
button
11
the value of humidity you want. After a few seconds
your chosen humidity value disappears and the display switches
over to the current humidity value of your room.
2. WATER LEVEL INDICATOR
If the red indicator lamp
10
is lit, this normally means that
water has to be refilled in the tank or that there is too much
water in the atomizing chamber and this must be skimmed off.
Should the indicator lamp stay on continuously despite a
correct water level, there is a malfunction. In this case, the
unit must be brought to the nearest service point.
3. NIGHT REDUCTION
The humidifier is equipped with an additional switch for
night operation. This lowers the noise level by reducing the
fan speed and also reduces the amount of humidity. This is
possible when you press the button
13
. On the LCD display
will appear a little moon. When you press a second time the
button
13
, the night reduction is switched off and the little
moon on the display disappears.
4. CONTINUOUS
When you press the button
8
, it is possible to switch the
unit over to a continuous run. That means that the unit will
operate without the humidistat control until the tank is
empty. On the LCD display will appear a circle. When you
press again the button
8
, the unit will switch over to the
automatic humidistat control mode and on the LCD display
the circle will disappear.
5 DESIRED HUMIDITY
When a comfortable humidity level is reached, lower the
humidity level (Humidistat) setting slowly until the electronic
for fog production shuts off. The desired humidity sign
on the display will appear, indicating that the humidity
setting has been reached. The electronic humidistat will
automatically restart the electronic for fog production each
time the humidity level falls below this setting. This “ON/OFF”
cycle will continue periodically while the humidifier is in use.
OPERATION
1. Place the unit on a level, dry surface that is insensitive to
water. Ensure that the air-filter vents
1
have enough room
for suction. The atomizer nozzle
3
must be unimpeded
in blowing off and must not be directed against objects or
surfaces in the immediate vicintity.
2. Remove the tank lid
4
and fill the water tank
5
with cold,
fresh tap water.
3. IMPORTANT: Please do not overfill the tank you can
damage the unit. Please fill tank only to the “max.” sign
shown on the scale. In case that the scale is missing in the
tank, the water level must be at least 1 cm under the edge
of the tank.
4. Before mounting the enclosed decalcifying filter
6
on the
tank filter neck, remove the packing sheeting. Attach the
decalcifying filter on the tank filter neck, align it along the
guide rail inside the tank and press it down to the stop. When
the filter is now under the water, please press the knob of the
integrated valve of the filter down to allow the air bubbles
to escape. Please do this procedure everytime you replace
the filter. We recommend to press the knob of the integrated
valve also once in a week for better function of the filter.
5. Replace the tank lid
4
on the water tank
5
.
6. Mount the atomizer nozzle
3
and turn it in the desired
direction.
7. Connect the unit to the power supply system with the plug.
8. Set the humidity control to your favorite value for continuous
adjustment of the desired humidity. The optimum value
between 40% and 60% is easy to adjust. You press the button
11
and
12
together and after some seconds on the LCD
display the current value of humidity starts to flash. Now it
is possible to adjust with the button or with the button the
value of humidity you want. After a few seconds your chosen
humidity value disappears and the display switches over
to the current humidity value of your room. This setting is
automatically maintained by your humidifier, which means: if
the air is too dry the humidifier will sense and automatically
cycle on. When the desired humidity is attained, the unit
switches off automatically.
9. If the water tank
5
is empty, the unit switches to a standby
position. This is indicated by the red signal light
10
“Add
water”. In this case, add water.
10. If you have a unit with night lowering, you can set this mode
of operation with the button
13
. The humidity discharged as
well as the noise produced are thereby lowered.
11. During the first hours of operation, the mist emitted may
have a peculiar smell. This will disappear after a while and is
caused by the granulate of the decalcifying filter that is fresh
from production.
ENGLISH
SAFETY NOTES
1. The unit must only be used to humidify the room air.
Inappropriate use can lead to hazards and damages for which
no liability is assumed.
2. Should the unit or the power cable have suffered damages
during transport (e.g. through violent impact), please do not
put it into operation under any circumstances. It must be
checked by an authorized service outlet.
3. This appliance is not intended for use by persons (including
children) with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning the
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
4. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
5. Never operate the unit or pull the plug with wet hands.
6. The unit must only be placed on a level, dry surface that is
insensitive to water.
7. Compare the data on the rating plate with those of your
power supply- they must be identical.
8. Always fill the unit with fresh, cool tap water only.
9. Never operate the unit without water.
10. Do not add aromas or additives to the water.
11. Never operate the unit without the decalcifying filter or when
the filter is used up. Exchange the decalcifying filter after 5
months at the latest.
12. Before cleaning, always pull the power plug.
13. During cleaning, take care that no water enters inside the
unit. When you empty the unit of the restwater, please take
care that the water does not run into the hole of the airflow
which is on top of the atomizing chamber
15
. If water goes
into this hole, the entire unit can be damaged. Please empty
the water on the opposite side of the airflow hole of the
atomizing chamber. Never dip the unit in water or put it in the
dishwashing machine.
14. If the machine has been put out of operation for a longer
period of time, rinse the water tank and the atomizing
chamber well before filling.
15. If the unit shows defects in functioning, please do not put it
into operation any more. It must be checked by an authorized
service outlet.
16. Repairs must only be made by authorized service outlets.
COMPONENTS
1
Air filterAir filter
2
Air filter flapAir filter flap
3
Atomizer nozzleAtomizer nozzle
4
Tank lidTank lid
5
Water tankWater tank
6
Decalcifying filter
7
ON/OFF switchON/OFF switch
8
Continuous operationContinuous operation
9
LCD displayLCD display
10
Indicator lamp “refill water”Indicator lamp “refill water”
11
Button minus (for less humidity)Button minus (for less humidity)
12
Button plus (for more humidity)Button plus (for more humidity)
13
Low-working night operationLow-working night operation
14
Lid of atomizing chamberLid of atomizing chamber
15
Atomizing chamberAtomizing chamber
FIRST USE
Before using the unit for the first time, you should note the
following points:
1. Remove all packing material from the unit (also the sheeting
from the decalcifying filter).
2. Please check your water hardness with the enclosed test strips
as described on Page 8 of the operating instructions.
ENGLISH
