Hagerco 294D - Constant-Latching Flush Bolt Set - For Inactive Wood Covered Composite Doors Installation guide

Hagerco
Brand
Hagerco
Model
294D - Constant-Latching Flush Bolt Set - For Inactive Wood Covered Composite Doors
Type
Installation guide

This manual is also suitable for

Hagerco 294D - Constant-Latching Flush Bolt Set - For Inactive Wood Covered Composite Doors

The Hagerco 294D is a constant-latching flush bolt set that is designed for use with inactive wood covered composite doors. This means that the flush bolt will automatically extend when the door is closed, and will retract when the door is opened. The flush bolt has a throw of 3/4", and can be adjusted to fit doors with a gap of up to 3/16" between them. The flush bolt is easy to install, and comes with all of the necessary hardware.

Some of the features of the Hagerco 294D include:

  • Constant-latching design for added security

Hagerco 294D - Constant-Latching Flush Bolt Set - For Inactive Wood Covered Composite Doors

The Hagerco 294D is a constant-latching flush bolt set that is designed for use with inactive wood covered composite doors. This means that the flush bolt will automatically extend when the door is closed, and will retract when the door is opened. The flush bolt has a throw of 3/4", and can be adjusted to fit doors with a gap of up to 3/16" between them. The flush bolt is easy to install, and comes with all of the necessary hardware.

Some of the features of the Hagerco 294D include:

  • Constant-latching design for added security
MORTISE THE INACTIVE DOOR USING HAGER TEMPLATE T-TA00173. REFER
1.
TO THIS TEMPLATE DURING THE INSTALLATION PROCESS.
INSTALL BOTH FLUSH BOLT HOUSINGS IN THE DOOR EDGE (DO NOT
2.
INSTALL SCREWS AT THIS TIME.)
ADJUST THE TOP ROD SO THAT THE TOP OF THE BOLT SITS FLUSH WITH THE
3.
TOP OF THE DOOR WHEN IN THE RETRACTED POSITION. ROTATE BOLT SO
THAT THE BEVEL IS FACING THE PUSH SIDE OF THE DOOR. ADJUST THE
BOTTOM ROD SO THAT THE TOP OF THE BOLT SITS FLUSH WITH THE BOTTOM
OF THE DOOR WHEN IN THE RETRACTED POSITION.
SLIDE HEAD GUIDES OVER THE BOLTS AND ATTACH TO THE TOP AND
4.
BOTTOM DOOR EDGES USING #8 COMBO SCREWS.
INSTALL FACEPLATES OVER THE HOUSING BRACKETS AND FASTEN TO THE
5.
DOOR USING (2) 8-32 X 1/2" MACH SCREWS AND (2) #8 COMBO SCREWS.
INSTALL STRIKES.
6.
HANG DOOR.
7.
INSTALL ACTIVE DOOR STRIKE ON ACTIVE DOOR USING CENTERLINE OF
8.
THE FLUSH BOLT CAM AS A GUIDE (
NOTE:
SURFACE MOUNT THE STRIKE
WHEN GAP BETWEEN THE DOORS IS 3/16"[4.7] OR GREATER. STRIKE CAN
STILL BE USED IF GAP IS SMALLER THAN 3/16"[4.7], BUT THE STRIKE WILL
HAVE TO BE MORTISED INTO THE ACTIVE DOOR EDGE.)
NOTE 1:
INSTALL COORDINATOR BEFORE FLUSH BOLTS.
NOTE 2
: BOLTS HAVE A MAX THROW OF 3/4"[19]. FIELD ADJUSTMENTS CAN BE
MADE TO ALLOW THE BOLTS TO EXTEND A GREATER DISTANCE, BUT THE DOOR
MUST BE TAKEN OFF THE HINGES TO MAKE ADJUSTMENTS TO THE BOTTOM FLUSH
BOLT!
NOTE 3:
OPTIONAL DUST PROOF STRIKE 280X MAY BE USED.
MORTISE THE INACTIVE DOOR USING HAGER TEMPLATE T-TA00172.
1.
REFER TO THIS TEMPLATE DURING THE INSTALLATION PROCESS.
INSTALL BOTH FLUSH BOLT HOUSINGS IN THE DOOR EDGE (DO NOT
2.
INSTALL SCREWS AT THIS TIME.)
THREAD THE RODS INTO THE HOUSINGS THROUGH THE HOLE IN THE
3.
TOP/BOTTOM OF THE DOOR. THE ROD SHOULD ATTACH IN A CLOCK-
WISE MOTION. ADJUST THE TOP ROD SO THAT THE TOP OF THE BOLT
SITS FLUSH WITH THE TOP OF THE DOOR WHEN IN THE RETRACTED
POSITION. ROTATE BOLT SO THAT THE BEVEL IS FACING THE PUSH SIDE
OF THE DOOR. ADJUST THE BOTTOM ROD SO THAT THE TOP OF THE
BOLT SITS FLUSH WITH THE BOTTOM OF THE DOOR WHEN IN THE
RETRACTED POSITION.
INSTALL FACE PLATES OVER THE HOUSING BRACKETS AND FASTEN TO
4.
THE DOOR USING (4) #8 COMBO SCREWS.
SLIDE HEAD GUIDES OVER THE BOLTS AND INSTALL TO THE TOP AND
5.
BOTTOM DOOR EDGES USING #8 COMBO SCREWS.
INSTALL STRIKES.
6.
HANG DOOR.
7.
INSTALL ACTIVE DOOR STRIKE ON ACTIVE DOOR USING CENTERLINE
8.
OF THE FLUSH BOLT CAM AS A GUIDE (
NOTE:
NOT RECOMMENDED IF
GAP BETWEEN THE TWO DOORS IS LESS THAN 3/16"[4.7])
NOTE 1:
INSTALL COORDINATOR BEFORE FLUSH BOLTS.
NOTE 2
: BOLTS HAVE A MAX THROW OF 3/4"[19]. FIELD ADJUSTMENTS CAN
BE MADE TO ALLOW THE BOLTS TO EXTEND A GREATER DISTANCE, BUT THE
DOOR MUST BE TAKEN OFF THE HINGES TO MAKE ADJUSTMENTS TO THE
BOTTOM FLUSH BOLT!
NOTE 3:
OPTIONAL DUST PROOF STRIKE 280X MAY BE USED.
294D
293D
PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLING
293D / 294D CONSTANT LATCHING FLUSH BOLT
INSTALLATION INSTRUCTIONS
REV: 01
DRAWING NO: I-TA01034
SHEET 1 OF 1
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
  • Page 1 1

Hagerco 294D - Constant-Latching Flush Bolt Set - For Inactive Wood Covered Composite Doors Installation guide

Hagerco
Brand
Hagerco
Model
294D - Constant-Latching Flush Bolt Set - For Inactive Wood Covered Composite Doors
Type
Installation guide
This manual is also suitable for

Hagerco 294D - Constant-Latching Flush Bolt Set - For Inactive Wood Covered Composite Doors

The Hagerco 294D is a constant-latching flush bolt set that is designed for use with inactive wood covered composite doors. This means that the flush bolt will automatically extend when the door is closed, and will retract when the door is opened. The flush bolt has a throw of 3/4", and can be adjusted to fit doors with a gap of up to 3/16" between them. The flush bolt is easy to install, and comes with all of the necessary hardware.

Some of the features of the Hagerco 294D include:

  • Constant-latching design for added security
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents