Hagerco 790-900 - Door of Any Material Electric Through Wires Modification instruction

Hagerco
Brand
Hagerco
Model
790-900 - Door of Any Material
Type
Electric Through Wires Modification instruction

This manual is also suitable for

Instructions SS Continuous Hinge with Electric Modifications – ETW
75009399
I-CS00165
Rev 5, Rev Date: 09/14/2020
Always visit www.hagerco.com for the latest Installation Instructions
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995
Page 1 of 2
ETW – Electric Through Wires
Door and Frame Preparation
For a grout filled frame, install a Mortar Box (HAGER 430). Failure to do so will void the hinge warranty.
1. Prepare the door and frame for installation using the standard installation instruction sheet furnished with the hinge, but
do not attach the hinge at this time.
2. Using your Stainless-Steel Continuous Hinge model, hinge length and handing; utilize Figure 1, Figure 2 and the
tables below to find the correct security plate recess centerline location for your door and frame. Dimensions below
are based on Hager’s standard ETW centerline locations and the industry standard of 1/8” clearance between the
top edge of the door opening and the top edge of the door. Call Hager Technical Support for Modified Length
Hinges and Non-Standard ETW centerline location.
790-900
Hinge Length
ETW Security Plate Pair
Centerline Location
(measured from the top of the hinge)
Left Hand or Right Hand
Reverse Security Plate Recess
Centerline Locations
D
F
D
F
79”
41 1/2
42 1/2
40 5/8
40 1/2
42 5/8
83”
43 1/2
42 1/2
44 5/8
44 1/2
42 5/8
85”
45 1/2
46 1/2
44 5/8
44 1/2
46 5/8
95”
55 3/8
54 3/8
56 1/2
56 3/8
54 1/2
119”
79 1/8
78 1/8
80 1/4
80 1/8
78 1/4
790-915
Hinge Length
ETW Security Plate Pair
Centerline Location
(measured from the top of the hinge)
Left Hand or Right Hand
Reverse Security Plate Recess
Centerline Locations
D
F
D
F
79”
41 1/2
42 1/2
40 5/8
40 1/2
42 5/8
83”
43 1/2
42 1/2
44 5/8
44 1/2
42 5/8
85”
45 1/2
46 1/2
44 5/8
46 1/2
44 5/8
95”
55 3/8
54 3/8
56 1/2
56 3/8
54 1/2
119”
79 1/8
78 1/8
80 1/4
80 1/8
78 1/4
Right Hand or Left Hand Reverse
Figure 1
Left Hand or Right Hand Reverse
Figure 2
Instructions SS Continuous Hinge with Electric Modifications – ETW
75009399
I-CS00165
Rev 5, Rev Date: 09/14/2020
Always visit www.hagerco.com for the latest Installation Instructions
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995
Page 2 of 2
3. Using the recess centerline locations above and in Figure 3, drill a 3/4” diameter access hole in both the frame and
the door. Using Figure 4, mortise a 1/8” deep recess for a flush fit of the security plate. After drilling and mortising,
deburr the holes to prevent damage to the wire leads.
Figure 3
(4-wire shown)
Figure 4
Installation
1. Connect the system wires from the door to the appropriate leads of the hinge door leaf as described in the system
wiring diagram found in Figure 5. Insulate the bare end of any unused wires.
2. Carefully slide the wires back through the access hole in the door. Make sure they are placed so that they will not
be cut or pinched as installation is completed. Attach the hinge to the door per the standard installation instruction
sheet supplied with the hinge.
3. Position the door at 90 degrees to the frame. Connect the system wires from the frame to the appropriate leads of
the hinge frame leaf. Insulate the bare end of any unused wires.
4. Carefully slide the wires back through the access hole in the frame. Make sure they are placed so that they will not
be cut or pinched as installation is completed.
5. Attach the hinge to the frame per the standard installation instruction sheet supplied with the hinge.
Figure 5: ETW security plate pair pattern depends on the hinge length, ETW center line location and handing
MAXIMUM ELECTRICAL
RATING CONTACT
Volts: 30VAC/DC
Amperes: 3.5A
OR
  • Page 1 1
  • Page 2 2

Hagerco 790-900 - Door of Any Material Electric Through Wires Modification instruction

Hagerco
Brand
Hagerco
Model
790-900 - Door of Any Material
Type
Electric Through Wires Modification instruction
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents