System Release Notes
Express5800/120Ld
System Release Notes
PN: 455-01573-002
Proprietary Notice and Liability Disclaimer
The information disclosed in this document, including all designs and related materials, is
the valuable property of NEC Computers Inc. and/or its licensors. NEC Computers Inc.
and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights
to this document, including all design, manufacturing, reproduction, use, and sales rights
thereto, except to the extent said rights are expressly granted to others.
The NEC Computers Inc. product(s) discussed in this document was warranted in
accordance with the terms of the Warranty Statement accompanying each product.
However, actual performance of each such product is dependent upon factors such as
system configuration, customer data, and operator control. Since implementation by
customers of each product may vary, the suitability of specific product configurations and
applications must be determined by the customer and is not warranted by NEC Computers
Inc.
To allow for design and specification improvements, the information in this document is
subject to change at any time, without notice. Reproduction of this document or portions
thereof without prior written approval of NEC Computers Inc. is prohibited.
Trademarks
Window, Windows NT, and Windows 2000 are registered trademarks of Microsoft Corporation.
Novell and NetWare are registered trademarks of Novell, Inc.
SCO OpenServer is a trademark of The Santa Cruz Operation, Inc.
UnixWare is a registered trademark of The Santa Cruz Operation, Inc.
All other product, brand, or trade names used in this publication are the trademarks or registered trademarks
of their respective trademark owners.
August 2000
Copyright 1999, 2000
NEC Computers Inc.
15 Business Park Way
Sacramento, CA 95828
All Rights Reserved
Express5800/120Ld
System Release Notes
The Express5800/120Ld System Release Notes provide up-to-date information
on your system. These notes also provide additional valuable information about
your system that was not included in the user’s guide.
Please read these notes in their entirety.
CONTENTS
Introduction ............................................................................................................................................3
General Comments.................................................................................................................................3
Advisories...............................................................................................................................................3
ExpressBuilder...................................................................................................................................3
BIOS Setup Utility.............................................................................................................................4
SCO....................................................................................................................................................4
System Hardware...............................................................................................................................4
ne
Express5800/120Ld System Release Notes 3
Introduction
These System Release Notes cover the following topics:
!
General Comments
!
Advisories
General Comments
The following general comments apply to this server.
!
Versions of the Network Operating Systems tested and recommended are:
Windows 2000®
Windows NT® 4.0 Server with Service Pack 6
Novell® NetWare® 5.0
IntraNetWare 4.11 with Support Pack 5b
SCO OpenServer™ 5.05 with Maintenance Supplement 505A.
UNIXWare® 7.1
Advisories
This section contains advisories on the ExpressBuilder
,
SCO, and the BIOS
Setup Utility.
ExpressBuilder
The following advisory applies to ExpressBuilder.
!
If you already have an operating system installed when creating a
maintenance partition, ExpressBuilder will warn you of the existing
partition. If you want to preserve the installed operating system, do not
create the maintenance partition or the existing operating system will be
overlaid by the maintenance partition.
!
ExpressBuilder EasySetup will always configure the Windows 2000 TCP/IP
Protocol IP settings to obtain an IP address automatically (DHCP),
regardless of the setting specified in EasySetup.
!
After installation, the Windows 2000 Device Manager may show an NEC
GEM SCSI Processor Device and/or an Unknown Device under Other
Devices. The Unknown Device is referenced on the baseboard management
controller. Both of these conditions can be cleared by installing the
ESMPRO Agent.
!
The ExpressBuilder DOS ASPI driver is not supported.
4 Express5800/120Ld System Release Notes
!
The Administrator Menu in the System Information Management segment
of the Offline Maintenance Utility is not user accessible.
!
ExpressBuilder operates in floppy emulation mode. Your system CD-ROM
drive is designated Drive A and your system diskette drive is Drive B. After
creating the Off-line Maintenance Utility diskette, ExpressBuilder prompts
you to remove the diskette from Drive B. At this prompt, remove the
diskette from your diskette drive.
BIOS Setup Utility
The following advisories apply to the BIOS Setup Utility (F2):
!
General Help (F1) description states that pressing the ESC or Alt-X keys
exits the BIOS Setup Utility. Pressing either of these keys exits the current
menu and returns you to the previous menu. If you are displaying the BIOS
Setup Utility Main Menu, pressing either of these keys takes you to the Exit
Menu.
SCO
The following advisory applies when using SCO 5.05:
!
During the installation of SCO or any time thereafter when booting SCO a
warning message may appear as follows:
WARNING: Cannot connect to APM, error 0x0036 System loaded, press
<Return> to start:
To prevent the WARNING message from appearing, boot the system to single-
user Mode. Edit the /etc/default/boot file. Add "apm.check=no" to the end of the
line indicated by the "DEFBOOTSTR=" entry.
System Hardware
The following advisory applies to the Plug and Play feature of your server's I/O
expansion boards.
!
The Windows 2000 Operating System requires that your server’s PnP O/S
feature be enabled. Before installing the Windows 2000 Operating System,
run the BIOS Setup Utility as described in Chapter 3 of your User’s Guide,
to verify the PnP O/S feature is enabled. Your User’s Guide is included on
ExpressBuilder.
The following advisory applies to the USB ports on your server's external device
connectors.
!
The factory standard default value of the USB ports on your server is
"Disabled". To enable them, the USB Controller feature in the Peripheral
Configuration Submenu of the BIOS Setup Utility "BIOS Setup
Configuration Settings" must be changed to "Enabled". Refer to
Chapter 3 of your User’s Guide. Your User’s Guide is included on
ExpressBuilder.
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
NEC Express5800/140Hb Release Notes
-
-
NEC Express5800/180Rb-7 Release Notes
-
-
-
-
-
-
-