P
P
FiberTwist–Series
Installation Guide
Buton oveview Pot oveview
Power potLAN pots
Unlock buton
Remove FiberTwist or Blind Cover – press and
hold while wisting counterclockwise
Reset buton (recessed)
Reset – press and release
LED dim buton
Dim LEDs – press and release to dim LEDs in
steps
System
Green – system ok
Green (blinking) – booting
Red – system error
Red (blinking) – insuicient optical signal
O – power o
Uplink
Green – link ok
Green (blinking) – link ok, no remote management
O – no link
LED oveview
Box contents
• Genexis FiberTwist (active device)
• Power adapter
• Label (self-adhesive)
• Installation Guide (this document)
Label position
The product label is positioned on the
back of the active device.
Preparation
Ensure there is a power socket
within reach of where the device
is being installed.
Impotant: Instructions need
to be followed precisely and
uninterrupted. This minimizes
the risk of damage to the iber
optic connectors, causing a severe
degradation of signal qualiy.
Dierent language versions of this document and additional product information
are availableon htps:genexis.euproductibewistdownloads
Installation guide
Remove Blind Cover (if present)
. Press and hold the unlock buton (see buton oveview).
. Rotate the Blind Cover counterclockwise till it blocks.
. Remove the Blind Cover from the baseplate (FTU) by pulling
it towards yourself.
. Store the Blind Cover in a safe place.
Remove dust cap
. Take the FiberTwist out of the box.
. The dust cap is connected to the red string
located on the rear of the FiberTwist.
. Remove the dust cap by pulling the red string.
. Store the dust cap in a safe place.
Twist!
. Place the FiberTwist on the FTU as shown in the picture below,
in a –degree angle.
. Rotate clockwise until it clicks into place.
. Make sure the FiberTwist is aligned squarely on the FTU,
each edge must line up directly with the FTU below.
Your FiberTwist is now installed!
Company Name
Genexis B.V.
Company Address
Lodewijkstraat a
AC Eindhoven
The Netherlands
Name and title of authorized person
Maaten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven --
The Netherlands
Hereby, Genexis B.V. declares that the products FiberTwist-P and
FiberTwist-P are in compliance with Directives EU, EU,
EU, Delegated Directive and Ecodesign Directive EC.
The full texts of the EU declaration of conformiy are available at the following
internet addresses respectively: htps:genexis.euredt-P,
htps:genexis.euredt-P
EU Declaration of Conformiy
Connecting the FiberTwist
. If required, connect your personal devices to the LAN pots via an RJ
nework cable.
. Connect the supplied power adapter to the FiberTwist and plug the adapter
into a power socket.
Warning: The FiberTwist is a Class laser product.
If at some point in the future it becomes necessay to uninstall the FiberTwist,
please place the Blind Cover back on the FTU immediately and put the dust cap
back on the FiberTwist.
Changing your router setings
Depending on the nework coniguration of your operator, the FiberTwist-P
and FiberTwist-P can also provide suppot for routing functionalities. If
this is the case, the router setings can be changed by logging in to the web GUI
using below instructions. If routing functionaliy is not suppoted by your Sevice
Provider, the web GUI will not be reachable.
. Connect a computer to one of the LAN pots.
. Log in to the web GUI by browsing to htp:router
Your username and password can be found on the label inside the product box.
Revision . - June - Copyright © Genexis Netherlands B.V. All rights reseved.
Genexis assumes no responsibiliy for any inaccuracies in this document. Genexis reseves
the right to change, modify, transfer, or othewise revise this publication without notice.
/
