Saris 8023 Assembly Instructions

Saris
Brand
Saris
Model
8023
Type
Assembly Instructions

This manual is also suitable for

Assembly Instructions
3-8 Bike
VERTICAL RACK
Bicycle Storage & Parking Solutions
Optional
Tools Required:
• 9/16” Combination wrench & 7/16“ Combination wrench
• Hammer drill (for anchors)
• ½” concrete drill bit (for anchors)
• Tape measure
Mounting Hardware – part # 6264 (sold separately)
Recommended for
8023, 8024, 8043, 8044; REQUIRED for
8033, 8034, 8063, 8064
WARNINGS:
• Mounting vertical rack to oor is recommended for single sided models
(8023, 8024, 8043, 8044) and REQUIRED for double sided models (8033,
8034, 8063, 8064).
• Manufacturer and seller expressly disclaim any and all liability for personal
injury, property damage or loss, whether direct, indirect or incidental,
resulting from the incorrect attachment, improper use, inadequate
maintenance, or neglect of this product.
WARRANTY:
We warrant this product to the rst consumer to be free from defect in
material and workmanship for a period of one year from date of purchase
(please retain your sales slip for your records). Any product or part thereof
found to be defective within that period will be replaced without charge
provided that (1) the product was not misused; (2) no alterations or
modications were made; (3) its failure resulted from a defect in material or
workmanship and not from normal wear expected in the use of the
product; (4) the product or part is delivered, freight prepaid, to Saris Cycling
Group. Manufacturer’s only obligation shall be to replace such products or
parts proved to be defective. Damage to mounting surface is not covered
under warranty.
SKU Decsrip�on Bike Spacing Ceiling Height Footprint W/Bikes
8023 3 bike, single sided, non locking ver�cal rack 18" 84" 54"X46"
8024 4 bike, single sided, non locking ver�cal rack 18" 84" 75"X46"
8043 3 bike, single sided, locking ver�cal rack 18" 84" 54"X90"
8044 4 bike, single sided, locking ver�cal rack 18" 84" 75"X90"
8033 6 bike, double sided, non locking ver�cal rack 18" 84" 54"X46"
8034 8 bike, double sided, non locking ver�cal rack 18" 84" 75"X46"
8063 6 bike, double sided, locking ve
r�cal rack 18" 84" 54"X90"
8064 8 bike, double sided, locking ver�cal 18" 84" 75"X90"
Product shown 8024
Part
8023
8024
8043
8044
8033
8034
8063
A
6006 Bike tray, locking
3
4
6
B
6003T Bike tray, non locking
3
4
6
8
C
Ver�cal 2” square side bar
2
2
2
2
2
2
2
D
2” x 24” x 1” C channel stabilizing foot
2
2
2
2
2
2
2
E
Connec�on plate, 6” x 6”
4
4
4
4
4
4
4
F
Horizontal cross bar, c channel, 54” long
2
2
2
2
F
Horizontal cross bar, c channel, 72” long
2
2
2
H
Tube caps (2” square plas�c)
2
2
2
2
2
2
2
I
Carriage Bolt, 1/4 – 20 x ½”
10
10
10
10
20
20
20
J
Carriage Bolt, ¼-20 x 2.5”
8
8
8
8
8
8
8
K
Carriage Bolt, 3/8
–
16 x 3”
8
8
8
8
8
8
8
L
Nut, 3/8-16
8
8
8
8
8
8
8
M
Nut, ¼ - 20
18
18
18
18
28
28
28
Product shown 8024
Step 2
STEP 1: LEG ASSEMBLY
• Assemble side supports and connect
feet (part D - 2x24x1) to side support
vertical tubes (part C), using connection
plate (part E), and Carriage Bolt (part K)
C
F
STEP 2 : HORIZONTAL CROSS BAR
• Attach Horizontal Cross bar (Part F) to each vertical
side support (part C), using carriage bolt (Part J)
Step 1
(x2)
Holes closer to the
edge on the ground.
Shown: 8044, 4 bike, single sided, locking vertical
rack
3/8 X 3”
1/4 X 2.5”
B
Step 3
STEP 3: ATTACH WHEEL TRAYS TO FRAME
SINGLE AND DOUBLE SIDED:
• Standard spacing – standard bike spacing is 18” on center. Use “Square”
oriented holes on cross bar (part F) to achieve standard bike spacing. To
connect Bike trays to rack, use bolt (part I) and nut (Part M) to secure Bike
Tracs to the cross bar (part F).
• Note: An additional Bike Trac can be added to all increase bike capacity by
1 bike for single sided racks, and 2 bikes for double sided racks. This will
change bike spacing to 14.5” on center. Use Diamond oriented holes on
cross bar (part F) when securing bike tracs.
STEP 4: MOUNTING RACK TO FLOOR
Mounting rack to oor is recommended for single sided models, and required
for double sided models.
• Before drilling mounting holes in concrete oor, investigate whether any
mechanicals are imbedded in concrete (ie. Radiant heat, water supply or drain
pipes…)
• Determine desired location of unit (mark hole locations using foot, part D, as
a guide).
• Using a ½” masonry drill bit, drill holes in cement 2” deep.
• Insert anchor shields into holes and tap in place with a hammer.
• Align holes in product foot (part D) with anchors and secure with 5/16 -8 x 2”
bolts.
Saris Cycling Group 5253 Verona Road Madison WI 53711 USA Ph: 608.274.6550 Fx: 608.274.1702 www.sarisinfrustructure.com
Open Side
Down
24214C 10/19
Shown: 8034, 8 bike, double sided, non locking
vertical rack
Product shown 8024
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Saris 8023 Assembly Instructions

Saris
Brand
Saris
Model
8023
Type
Assembly Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents