Eti 54321142 User guide

Part # FPE-22-40-840-MV-D Model # 54320142

FPE-22-40-850-MV-D 54320162

FPE-22-40-835-MV-D 64201131

FPE-24-50-840-MV-D 54321142

FPE-24-50-850-MV-D 54321162

FPE-24-50-835-MV-D 64201231

USE AND CARE GUIDE

LED FLAT PANEL

Questions, problems, missing parts?

Call ETiSSL Customer Service

8 a.m. - 5 p.m., CST, Monday - Friday

1-855-ETI-SSLI (1-855-384-7754)

www.ETiSSL.com

THANK YOU

We appreciate the trust and conﬁdence you have placed in ETi through the purchase of this LED light.

Visit us online to see our full line of products. Thank you for choosing ETi!

2

Table of Contents

Table of Contents ...................................2

Safety Information ..................................2

Warranty ..........................................2

Pre-Installation .....................................3

Planning Installation ...............................3

Tools Required ....................................3

Package Contents .................................3

Hardware Available To Purchase For Optional Installation

Methods .........................................3

Grid Ceiling Installation ..............................4

Optional Installation Methods .........................6

Suspension Mounting ..............................6

Surface Mounting .................................8

Care and Cleaning .................................10

Troubleshooting ...................................10

Safety Information

WARNING: Carefully read and understand the information

given in this manual before beginning the assembly and

installation. Failure to do so could lead to electric shock, ﬁre,

or other injuries which could be hazardous or even fatal.

WARNING: Ensure the electricity to the wires you are

working on is shut off. Either remove the fuse or turn off the

circuit breaker.

NOTICE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

□ Reorient or relocate the receiving antenna.

□ Increase the separation between the equipment and the receiver.

□ Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations not expressly approved

by the party responsible for compliance could void the user’s

authority to operate the equipment.

Warranty

This product is warranted for a period of 5 years from the date of original purchase against defects in materials and workmanship. If this

product should fail to operate due to defects in material or workmanship within 60 months of purchase, see www.ETiSSL.com for details.

This product will be repaired or replaced, at ETi’s option. This warranty is expressly limited to repair or replacement of product, and liability

for direct, incidental, or consequential damages is hereby expressly excluded. Some states do not allow exclusions of direct, incidental or

consequential damages, so the above limitation of exclusion may not apply to you. This warranty gives the consumer speciﬁc legal rights,

which vary from state to state. WARRANTY IS VOID IF PRODUCT IS NOT USED FOR THE PURPOSE WHICH THIS PRODUCT IS MANUFACTURED.

3 www.ETiSSL.com

Please contact 1-855-384-7754 for further assistance.

Pre-Installation

PLANNING INSTALLATION

Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with the package contents

list. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement

parts.

NOTE: Keep your receipt and these instructions for proof of purchase.

If you are unfamiliar with electrical installations, we recommend you contact a qualiﬁed electrician to do the installation.

NOTE: Two people are recommended for the optional surface mount installation of this light ﬁxture.

TOOLS REQUIRED

Phillips

Screwdriver

Safety

Goggles

Gloves Ladder

Wire

Strippers

Electrical

Tape

Power Drill

with drill bits

PACKAGE CONTENTS

Part Description Quantity

A LED Flat Panel 1

HARDWARE AVAILABLE TO PURCHASE FOR OPTIONAL INSTALLATION METHODS

NOTE: Hardware kits for surface mounting and suspension mounting are sold as separate accessories. Please contact ETiSSL Customer

Service 1-855-384-7754 for additional information.

NOTE: Hardware not shown to actual size.

Part Description Quantity Part #

AA Aircraft Cable for

Suspension Mounting

2 95457326101

BB Surface Mounting Kit for

2’ x 2’ Flat Panel

1 FPE-SMK-22

CC Surface Mounting Kit for

2’ x 4’ Flat Panel

1 FPE-SMK-24

A

x 12

Surface Mounting Kits - BB and CC

AA

x 2

x 4

4

Installation

Grid Ceiling Installation

Select a suitable location that can support the weight of the ﬁxture. Determine the method of mounting before beginning installation.

WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the

circuit breaker before removing the existing light ﬁxture or installing the new one.

With the power disconnected to the electrical box, remove the existing ﬁxture. Make a sketch of how the current ﬁxture is wired (by wire

color) or mark the wires with masking tape and a pencil so you will know how to properly reconnect the wires to the new LED light ﬁxture.

1

Replacing existing light ﬁxture

□ Remove the existing light ﬁxture from the grid

ceiling.

CAUTION: The weight of the LED ﬂat panel (A) is not designed to be supported by the ceiling grid. The LED ﬂat panel should be connected

back to the structure. Failure to do so can cause serious injury.

Mounting Clip

2

Securing the ﬂat panel

□ Bend each of the mounting

clips on the back of the LED

ﬂat panel (A) upward until

they are perpendicular to the

back surface of the ﬂat panel.

□ Bend the top part of each

mounting clip 90 degrees so

the hook is facing outward.

□ Place the LED ﬂat panel (A)

into the ceiling grid, hooking

the mounting clips over the

grid ceiling supports to secure

the LED ﬂat panel (A).

A

5 www.ETiSSL.com

Please contact 1-855-384-7754 for further assistance.

3

Connecting the electrical wires

□ Remove the driver cover to access the wiring and push connectors.

□ Insert the live black wire from the electrical outlet box into the push connector

opening labeled “ACL” in the driver box on the back of the LED ﬂat panel (A).

□ Insert the neutral white wire from the electrical outlet box into the push connector

opening labeled “ACN” in the driver box on the back of the LED ﬂat panel (A).

□ Connect the ground wire from the electrical outlet box to the yellow wire in the driver

box on the back of the LED ﬂat panel (A).

□ If a 0-10v dimming circuit is available, insert the purple wire from the electrical outlet

box into the push connector labeled “DIM+” and the gray wire from the electrical

outlet box into the push connector labeled “DIM-” in the driver box on the back of the

LED ﬂat panel (A).

□ Replace the driver cover once wiring connections are complete, fully tightening the

screw to hold it securely in place.

CAUTION: Do not allow the DIM+/- and LED +/- wires to make contact as it will cause

damage to the LED Driver.

4

Restoring power

□ Restore power at the electrical panel.

□ Turn on the light switch to activate the ﬁxture.

Grid Ceiling Installation (continued)

LED Driver

Red

White

Black

Gray

Purple

Green

Yellow

Dim-

Dim+

LED-

LED+

ACL

ACN

6

Optional Installation Methods

For mounting to drywall:

Toggle bolt x 4

Part Description Quantity

Toggle Bolts Consisting of a No. 10-24 bolt 2-7/8 inches long with two

tapered wings 1 by 5/16 inch.

4

Studs Measuring 1-3/4 inches overall and having 1-1/4 inches of

wood screw threads on one end and at least six No. 10-24

machine screw threads on the other end.

2

Metal Hooks With a No. 10-24 threaded hole that engages the bolt threads. 4

For mounting to wood:

Hook screw x 4

NOTICE: Toggle bolts are not considered an acceptable means of support in Canada, in accordance with CSA C22.2 No. 250.4.

NOTE: Eye hooks can be used as an alternate method of attaching the ﬁxture to the ceiling.

Suspension Mounting

NOTE: Separate mounting hardware (not included) not shown to actual size.

1

Mounting to drywall

□ Determine the position for the

four toggles to be secured in

the drywall mounting surface.

□ Drill four holes large enough

to clear the closed ﬂaps of the

butterﬂy nut on the toggle bolt

(not included). Make sure to

fasten the toggle bolt into the

butterﬂy nut before inserting

the ﬂaps into the ceiling.

□ Tighten the toggle bolts.

2

Mounting to wood

□ Drill four 1/16 in. diameter

holes in the ceiling to

accommodate hook screws

(not included). Make sure

to fasten the combo wood-

machine end into the metal

hook.

□ Tighten the hook screws (not

included) into the wood.

NOTE: If using eye hooks in the

ceiling instead, release the short end of

the aircraft cable from the quick cable-

lock by pushing in the cable release

and feed the aircraft cable through the

eye hook before reinserting it into the

quick cable-lock.

3

Attaching the aircraft

cable to the ceiling

□ Place the loop of the aircraft cable

(AA) (not included) over each mounting

hook.

AA

7 www.ETiSSL.com

Please contact 1-855-384-7754 for further assistance.

Suspension Mounting (continued)

6

Restoring power

□ Restore power at the electrical panel.

□ Turn on the light switch to activate the ﬁxture.

4

Attaching the LED ﬂat panel to the

aircraft cables

□ Bend each of the mounting clips on the back of the LED ﬂat

panel (A) upward until they are perpendicular to the back

surface of the ﬂat panel.

□ Attach the S hooks at the bottom of the aircraft cables (AA) to

the mounting clips on the LED ﬂat panel (A).

□ Slide the quick cable-lock down each aircraft cable to position

the LED ﬂat panel (A) at the desired height.

□ Push in the bottom cable release while ﬁrmly holding the

aircraft cable and feed it back through the quick cable-lock to

further adjust the height, if needed.

NOTICE: The LED ﬂat panel (A) must hang a minimum of 3 in. from the ceiling.

5

Connecting the electrical wires

□ Remove the driver cover to access the wiring and push connectors.

□ Insert the live black wire from the electrical outlet box into the push connector

opening labeled “ACL” in the driver box on the back of the LED ﬂat panel (A).

□ Insert the neutral white wire from the electrical outlet box into the push connector

opening labeled “ACN” in the driver box on the back of the LED ﬂat panel (A).

□ Connect the ground wire from the electrical outlet box to the yellow wire in the

driver box on the back of the LED ﬂat panel (A).

□ If a 0-10v dimming circuit is available, insert the purple wire from the electrical

outlet box into the push connector labeled “DIM+” and the gray wire from the

electrical outlet box into the push connector labeled “DIM-” in the driver box on the

back of the LED Flat Panel (A).

□ Replace the driver cover once wiring connections are complete, fully tightening the

screw to hold it securely in place.

CAUTION: Do not allow the DIM+/- and LED +/- wires to make contact as it will cause

damage to the LED Driver.

AA

Quick Cable Lock

Mounting Clip

A

LED Driver

Red

White

Black

Gray

Purple

Green

Yellow

Dim-

Dim+

LED-

LED+

ACL

ACN

8

Surface Mounting

1

Installing the mounting brackets

□ Connect three of the mounting brackets from the

appropriately sized Surface Mounting Kit (BB or CC)

using the screws included in the kit.

□ Use a Phillips

screwdriver

(not included)

to tighten the

screws.

2

Attaching the mounting brackets to

the ceiling

□ With help from another person, hold the assembled

mounting brackets to the ceiling and use a pencil to mark

the locations of the mounting holes.

□ Drill four 1/4 in. diameter holes into the four screw

locations marked on the ceiling.

□ Insert a drywall anchor into each of the drilled holes.

□ Secure the

mounting

brackets tightly

to the ceiling

using four

screws inserted

into the drywall

anchors.

3

Connecting the electrical wires

□ Remove the driver cover to access the wiring and push connectors.

□ With help from another person, hold the LED ﬂat panel (A) near the ceiling while

connecting the electrical wires.

□ Insert the live black wire from the electrical outlet box into the push connector

opening labeled “ACL” in the driver box on the back of the LED ﬂat panel (A).

□ Insert the neutral white wire from the electrical outlet box into the push connector

opening labeled “ACN” in the driver box on the back of the LED ﬂat panel (A).

□ Connect the ground wire from the electrical outlet box to the yellow wire in the driver

box on the back of the LED ﬂat panel (A).

□ If a 0-10v dimming circuit is available, insert the purple wire from the electrical outlet

box into the push connector labeled “DIM+” and the gray wire from the electrical

outlet box into the push connector labeled “DIM-” in the driver box on the back of the

LED Flat Panel (A).

□ Replace the driver cover once wiring connections are complete, fully tightening the

screw to hold it securely in place.

CAUTION: Do not allow the DIM+/- and LED +/- wires to make contact as it will cause

damage to the LED Driver.

LED Driver

Red

White

Black

Gray

Purple

Green

Yellow

Dim-

Dim+

LED-

LED+

ACL

ACN

9 www.ETiSSL.com

Please contact 1-855-384-7754 for further assistance.

Surface Mounting (continued)

5

Restoring power

□ Restore power at the electrical panel.

□ Turn on the light switch to activate the ﬁxture.

4

Inserting the LED ﬂat panel

□ Slide the LED ﬂat panel (A) into the mounting bracket.

□ Connect the fourth mounting bracket with the four

remaining screws using a Philips Screwdriver (not

included).

A

10

Troubleshooting

WARNING: Before doing any work on the ﬁxture, disconnect power to the light ﬁxture.

Minor problems often can be ﬁxed without the help of an electrician.

Problem Possible Cause Solution

The ﬁxture will not light. The power is off. Ensure the power supply is on.

The circuit breaker is off. Ensure the circuit breaker is in the on position.

There is a bad connection. Check to ensure proper wire connections are made.

Contact a qualiﬁed electrician.

There is a defective switch. Contact a qualiﬁed electrician.

The fuse blows or the circuit breaker

trips when the light is turned on.

The wires are crossed or the power

wire is grounding out.

Check the wire connections.

Contact a qualiﬁed electrician or call customer

service 1-855-384-7754.

Care and Cleaning

CAUTION: Before attempting to clean the ﬁxture, disconnect the power to the ﬁxture by turning the breaker off or removing the fuse from

the fuse box.

□ Clean the ﬁxture with a soft, dry cloth.

□ Do not use cleaners with chemicals, solvents, or harsh abrasives.

□ Do not use liquid cleaner on the LEDs, LED driver, or wiring inside the light ﬁxture.

Care and Cleaning

CAUTION: Before attempting to clean the ﬁxture, disconnect the power to the ﬁxture by turning the breaker off or removing the fuse from

the fuse box.

□ Clean the ﬁxture with a soft, dry cloth.

□ Do not use cleaners with chemicals, solvents, or harsh abrasives.

□ Do not use liquid cleaner on the LEDs, LED driver, or wiring inside the light ﬁxture.

11 www.ETiSSL.com

Please contact 1-855-384-7754 for further assistance.

Notes

Questions, problems, missing parts?

Call ETiSSL Customer Service

8 a.m. - 5 p.m., CST, Monday - Friday

1-855-ETI-SSLI (1-855-384-7754)

www.ETiSSL.com

Retain this manual for future use.

Page is loading ...

Eti 54321142 User guide

Eti 54321142 User guide

in other languages

Related papers

Other documents