Lexibook Move Cam DJ-290SW Owner's manual

Page is loading ...

18

ENGLISH

VIDEO CAMERA DESCRIPTION

CONTENTS OF THE PACKAGING

Front view

1. Lens

2. Microphone

3. Compensating lamp

4. Self-timer LED

Side view, with door open

5. Delete

6. Playback

7. Mode

8. TFT LCD screen

9. Left / Self-timer

10. Power

11. Down

12. Menu

1 x digital video camera / 1 x CD-ROM / 1 x USB cable / 1 x A/V cable

WARNING: All packaging materials, such as tape, plastic sheets, wire ties and tags are not part

of this product and should be discarded for your child’s safety.

1. Make sure the video camera is switched off.

2. Using a screwdriver, open the cover of the battery compartment.

3. Insert 3 x LR03/AAA 1,5V type batteries (not included) with the positive (+) and negative

(-) poles matching the directions indicated in the battery compartment, and shown below.

4. Close the battery compartment and tighten the screw.

INSERTING NEW BATTERIES

Note: When the low battery icon appears on the LCD screen, replace the batteries.

13. AV out jack

14. USB jack

15. Right / LED On/Off

16. OK

17. Shutter

18. Up / Display

19. W / Zoom out

20. T / Zoom in

21. Speaker

Base view

22. Tripod socket

23. SD card slot

24. Battery compartment

INSTALLING A MEMORY CARD (NOT INCLUDED)

This camera does not have an internal memory and requires an SD, MMC or SDHC card (not

included) to record pictures and videos. To insert the card, please:

1. Turn the video camera off.

2. Disable the write-protect switch on the memory card (this

is used to protect data from accidental deletion, and needs

to be switched off before recording, formatting or deleting

les on the memory card).

3. Remove the rubber cover from the SD slot.

4. Orient the card correctly, and push rmly into the slot

as illustrated.

Note:

• Never insert any other object into the memory card slot.

• Never remove the memory card while the camera is switched on.

• Never force the card into the slot if you feel resistance.

• If there is no SD card inserted in the video camera, the LCD screen will display the message

“No card” when trying to shoot a video or take a picture.

• When an external memory card has been inserted in the camera, all photos/videos taken will

be stored on the external memory card.

• To remove the card, push it in slightly to release it from the slot.

WARNING: Malfunction or loss of memory may be caused by strong frequency interference or

electrostatic discharge. Should any abnormal function occur, remove the batteries and insert

them again.

19

ENGLISH

VIDEO CAMERA DESCRIPTION

CONTENTS OF THE PACKAGING

1 x digital video camera / 1 x CD-ROM / 1 x USB cable / 1 x A/V cable

WARNING: All packaging materials, such as tape, plastic sheets, wire ties and tags are not part

of this product and should be discarded for your child’s safety.

1. Make sure the video camera is switched off.

2. Using a screwdriver, open the cover of the battery compartment.

3. Insert 3 x LR03/AAA 1,5V type batteries (not included) with the positive (+) and negative

(-) poles matching the directions indicated in the battery compartment, and shown below.

4. Close the battery compartment and tighten the screw.

INSERTING NEW BATTERIES

Note: When the low battery icon appears on the LCD screen, replace the batteries.

INSTALLING A MEMORY CARD (NOT INCLUDED)

This camera does not have an internal memory and requires an SD, MMC or SDHC card (not

included) to record pictures and videos. To insert the card, please:

1. Turn the video camera off.

2. Disable the write-protect switch on the memory card (this

is used to protect data from accidental deletion, and needs

to be switched off before recording, formatting or deleting

les on the memory card).

3. Remove the rubber cover from the SD slot.

4. Orient the card correctly, and push rmly into the slot

as illustrated.

Note:

• Never insert any other object into the memory card slot.

• Never remove the memory card while the camera is switched on.

• Never force the card into the slot if you feel resistance.

• If there is no SD card inserted in the video camera, the LCD screen will display the message

“No card” when trying to shoot a video or take a picture.

• When an external memory card has been inserted in the camera, all photos/videos taken will

be stored on the external memory card.

• To remove the card, push it in slightly to release it from the slot.

IMPORTANT NOTE: You must add a micro SD card to increase the storage capacity of the

unit and use the video camera.

Non-rechargeable batteries are not to be recharged. Rechargeable batteries are to be

removed from the product before being charged. Rechargeable batteries are only to be

charged under adult supervision. Different types of batteries or new and used batteries are not

to be mixed. Only batteries of the same or equivalent type as recommended are to be used.

Batteries are to be inserted with the correct polarity. Exhausted batteries are to be removed

from the product. The supply terminals are not to be short circuited. Do not throw batteries into

a re. Remove the batteries if you are not going to use the product for a long period of time.

WARNING: Malfunction or loss of memory may be caused by strong frequency interference or

electrostatic discharge. Should any abnormal function occur, remove the batteries and insert

them again.

20

ENGLISH

SETTING THE DATE AND TIME

1. Turn the power on. Press Menu and select the Setup menu .

2. Use the Up and Down keys to select “Date & Time”, then

press OK.

3. Use the Up and Down keys to change the highlighted setting,

and use the Left and Right keys to move between settings.

4. Press OK to conrm, and press the Menu key to close.

CHOOSING A MODE

This video camera has three recording modes: video, capture (for still pictures) and audio. When

you turn the camera on, the default mode is video. Press the Mode button to change the mode,

indicated by icons on the LCD display.

Display Title Description

Capture mode For taking still photos.

Video mode For recording movie clips.

Audio mode For recording audio les.

TURNING THE VIDEO CAMERA ON AND OFF

SETTING THE LANGUAGE

Please select a language before using the video camera for the rst time.

1. Turn the power on. Press Menu and then the Right key to select the Setup menu .

2. Use the Up and Down keys to select the Language menu, then press OK or the Right key

to conrm.

3. Use the Up and Down keys to select the desired language, then press OK.

4. Press the Menu key to close.

Open the LCD panel, and press the Power key to turn the video camera on or off.

Note: The video camera will automatically power off after a period of inactivity. To change the

power-off time, select the “Power Save” function in the Setup menu .

FORMATTING THE MEMORY CARD

All previous les will be deleted when formatting the memory card, including protected les.

Please download important les to your computer before formatting.

1. Turn the power on, press the Menu key to display the menu, and press the Right key to select

the Setup menu .

2. Press the Up or Down keys to select “Format”, then press the OK or Right key to conrm.

3. Press the Up or Down key to select “YES”, and press OK to erase all previous data.

Note: To preview recorded les, press the Playback key to set the playback mode. To return to

record mode, press the Playback key again.

21

ENGLISH

SETTING THE DATE AND TIME

CHOOSING A MODE

This video camera has three recording modes: video, capture (for still pictures) and audio. When

you turn the camera on, the default mode is video. Press the Mode button to change the mode,

indicated by icons on the LCD display.

Display Title Description

Capture mode For taking still photos.

Video mode For recording movie clips.

Audio mode For recording audio les.

TURNING THE VIDEO CAMERA ON AND OFF

SETTING THE LANGUAGE

Please select a language before using the video camera for the rst time.

1. Turn the power on. Press Menu and then the Right key to select the Setup menu .

2. Use the Up and Down keys to select the Language menu, then press OK or the Right key

to conrm.

3. Use the Up and Down keys to select the desired language, then press OK.

4. Press the Menu key to close.

Open the LCD panel, and press the Power key to turn the video camera on or off.

Note: The video camera will automatically power off after a period of inactivity. To change the

power-off time, select the “Power Save” function in the Setup menu .

FORMATTING THE MEMORY CARD

All previous les will be deleted when formatting the memory card, including protected les.

Please download important les to your computer before formatting.

1. Turn the power on, press the Menu key to display the menu, and press the Right key to select

the Setup menu .

2. Press the Up or Down keys to select “Format”, then press the OK or Right key to conrm.

3. Press the Up or Down key to select “YES”, and press OK to erase all previous data.

Note: To preview recorded les, press the Playback key to set the playback mode. To return to

record mode, press the Playback key again.

SHOOTING VIDEOS (video mode)

Screen in video mode:

1. Turn on your video camera. The default mode is video (the icon is displayed on the

screen).

2. Hold your video camera steady and press the Shutter key to start shooting. The recording

length is displayed on the LCD screen.

3. To pause, press the Up key. To continue recording, press the Up key again.

4. Press the Shutter button again to end recording. If the memory is full, the camera will stop

recording automatically.

Note:

• If there is not enough light, press the Right / LED key to turn on the compensating lamp. Press

the key again to switch it off.

• If there is no SD card inserted in the video camera, when trying to shoot a video, the screen

will display “No card” and the video will not be saved in memory. Insert a SD memory card to

increase the storage capacity.

White balance indicator

Video record mode

Memory card inserted

Battery level indicator

Full

Half

Low

Empty

Auto

Daylight

Cloudy

Fluorescent

Tungsten

Resolution indicator

Memory capacity

22

ENGLISH

1. Turn on your video camera.

2. Press the Mode key to switch to capture mode (the icon appears on the screen).

3. Use the LCD screen to compose your shot.

4. Press the Shutter button to take the photograph.

Note:

• The number of pictures you have space for on your memory card (memory capacity) is

displayed on the screen and automatically decreases by one each time a picture is taken. The

words “Memory Full” will appear when there is no space left on your memory card.

• When there is insufcient light, press the Right / LED key to turn the compensating lamp on.

Press the key again to switch it off.

• Do not remove the memory card or batteries while the video camera is saving or the image

may be lost.

Using the self-timer and burst snapshot

The self-timer sets a delay from the time the Shutter button is pressed to the time the picture is

taken. The burst snapshot takes three pictures continuously.

1. To set the self-timer and burst functions, turn the camera on and set to capture mode using

the Mode key.

2. Use the Left key to select the self-timer mode: each time the key is pressed the icon in the

upper left corner changes.

TAKING PICTURES (capture mode)

Screen in capture mode:

1. Turn the video camera on and use the Mode key to choose audio record mode.

2. Press the Shutter button to start recording. To pause, press the Up key; press the Up key

again to continue.

3. Press the Shutter button to end the recording. The recording will stop automatically if the

memory is full.

Note: The length of the recording will be displayed on the screen while recording.

Capture mode

Memory card inserted

Battery level indicator

Resolution indicator

White balance indicator

Memory capacity

Auto

Lumière du jour

Nuageux

Fluorescent

Tungstène

Full

Half

Low

Empty

23

ENGLISH

1. Turn on your video camera.

2. Press the Mode key to switch to capture mode (the icon appears on the screen).

3. Use the LCD screen to compose your shot.

4. Press the Shutter button to take the photograph.

Note:

• The number of pictures you have space for on your memory card (memory capacity) is

displayed on the screen and automatically decreases by one each time a picture is taken. The

words “Memory Full” will appear when there is no space left on your memory card.

• When there is insufcient light, press the Right / LED key to turn the compensating lamp on.

Press the key again to switch it off.

• Do not remove the memory card or batteries while the video camera is saving or the image

may be lost.

Using the self-timer and burst snapshot

The self-timer sets a delay from the time the Shutter button is pressed to the time the picture is

taken. The burst snapshot takes three pictures continuously.

1. To set the self-timer and burst functions, turn the camera on and set to capture mode using

the Mode key.

2. Use the Left key to select the self-timer mode: each time the key is pressed the icon in the

upper left corner changes.

TAKING PICTURES (capture mode)

Off: takes pictures immediately.

2 seconds: the shutter release will delay for two seconds.

10 seconds: the shutter release will delay for 10 seconds.

Burst snapshot: press the Shutter button once to take three pictures continuously.

Note: You can also set the self-timer and burst snapshot using the Capture menu.

Using the zoom function

The digital zoom moves in or out using the W (wide angle) and T (telephoto) keys.

1. Turn the video camera on and set it to capture or video record mode using the Mode key.

2. Press the W or T button to compose the image. The level of magnication is displayed on

the screen.

3. Press the Shutter button to capture the picture.

RECORDING AUDIO FILES

Screen in audio mode:

1. Turn the video camera on and use the Mode key to choose audio record mode.

2. Press the Shutter button to start recording. To pause, press the Up key; press the Up key

again to continue.

3. Press the Shutter button to end the recording. The recording will stop automatically if the

memory is full.

Note: The length of the recording will be displayed on the screen while recording.

Audio record mode

The time of record

Memory card inserted

Battery level indicator

Full

Half

Low

Empty

Memory capacity

24

ENGLISH

SETTINGS MENU

In record mode, press the Up, Down, Left, Right and OK keys to access the settings menus.

Please note, there is no menu for the audio record mode.

Video and capture mode

1. In video record or capture mode, press the Menu key to display

the menu. Use the Up and Down keys to select the sub-menus, and

the OK or Right key to conrm.

2. Use the Up and Down keys to choose an item on the sub-menu,

and press OK to conrm.

3. Press the Menu key to close.

Video menu

• Movie size: select this option to choose le sizes – set small le sizes to record for longer.

Three sizes are available: 1280x720, 720x480 and 640x480.

• Frame rate: choose High or Low. Select Low to record for longer.

• Metering: select this option to change the brightness of the picture.

- Center: the exposure is calculated on the light in the middle of the image. Suitable for general use

.

- Multi: exposure calculated on the average light.

- Spot: only the spot in the center of the LCD screen is metered for light.

• White balance: select this option to suit the light source – Auto, Daylight, Cloudy, Fluorescent

and Tungsten.

Capture menu

• Resolution: select this option to set the resolution of your photograph. Choose from (high to

low) 4000x3000, 2048x1536, 1280x960 or 640x480.

• Quality: select a lower image quality to reduce the le size and take more photographs.

Choose from Super Fine, Fine and Normal.

• Metering: see above.

• White balance: see above.

• Exposure: select this option to set the exposure manually in unusual lighting conditions such

as indirect indoor lighting, dark backgrounds or strong backlight. Settings from –2.0 to 2.0.

• Driver mode: select this option to turn on the self-timer and burst snapshot functions. Choose

a two-second or 10-second self-timer delay, or a three-shot burst.

• Effect: select this option to choose a special-effect tone for the photograph. Choose from

normal, B&W (black & white), sepia, negative, red, green or blue.

• Date stamp: select this option to add a date or a date and a time to your pictures.

Setup menu

1. Power on, press the Menu key then the Right key to select the Setup menu .

2. Use the Up and Down keys to choose a sub-menu, then press OK to enter.

25

ENGLISH

SETTINGS MENU

In record mode, press the Up, Down, Left, Right and OK keys to access the settings menus.

Please note, there is no menu for the audio record mode.

Video and capture mode

1. In video record or capture mode, press the Menu key to display

the menu. Use the Up and Down keys to select the sub-menus, and

the OK or Right key to conrm.

2. Use the Up and Down keys to choose an item on the sub-menu,

and press OK to conrm.

3. Press the Menu key to close.

Video menu

• Movie size: select this option to choose le sizes – set small le sizes to record for longer.

Three sizes are available: 1280x720, 720x480 and 640x480.

• Frame rate: choose High or Low. Select Low to record for longer.

• Metering: select this option to change the brightness of the picture.

- Center: the exposure is calculated on the light in the middle of the image. Suitable for general use

.

- Multi: exposure calculated on the average light.

- Spot: only the spot in the center of the LCD screen is metered for light.

• White balance: select this option to suit the light source – Auto, Daylight, Cloudy, Fluorescent

and Tungsten.

Capture menu

• Resolution: select this option to set the resolution of your photograph. Choose from (high to

low) 4000x3000, 2048x1536, 1280x960 or 640x480.

• Quality: select a lower image quality to reduce the le size and take more photographs.

Choose from Super Fine, Fine and Normal.

• Metering: see above.

• White balance: see above.

• Exposure: select this option to set the exposure manually in unusual lighting conditions such

as indirect indoor lighting, dark backgrounds or strong backlight. Settings from –2.0 to 2.0.

• Driver mode: select this option to turn on the self-timer and burst snapshot functions. Choose

a two-second or 10-second self-timer delay, or a three-shot burst.

• Effect: select this option to choose a special-effect tone for the photograph. Choose from

normal, B&W (black & white), sepia, negative, red, green or blue.

• Date stamp: select this option to add a date or a date and a time to your pictures.

Setup menu

1. Power on, press the Menu key then the Right key to select the Setup menu .

2. Use the Up and Down keys to choose a sub-menu, then press OK to enter.

Screen in playback mode:

Viewing photographs

1. Turn the video camera on and press the Playback key . The latest recorded le appears

on the screen. If there are no images stored a “No File” message appears.

2. Use the Left and Right keys to preview (next/previous image).

Viewing videos and audio les

1. Use the Left and Right keys to select the video clip or audio le you wish to play

2. Press the Shutter button to start playing, and the Menu key to end. To pause, press the Up

key; press the Up key again to continue.

PLAYBACK MODE

3. Use the Up and Down keys to choose an item on the sub-menu and press OK to conrm.

4. Press the Menu key to close.

• Sounds: using the Right key, choose the sounds for the Shutter and Start-up functions. Beep

sets the operation sound and Volume adjusts the sound level.

• Auto review: select this option to choose how long to review a picture for on the screen

immediately after shooting. Choose one second, three seconds, or switch the function off.

• Power frequency: select this option to set the right frequency for your region – 60Hz or 50Hz.

• Power save: select this option to choose the time period before the video camera powers

off – one minute, three minutes, ve minutes or Off to switch the

function off..

• Date & Time: see page 16.

• Language: see page 15.

• TV out: select the right video setting for your region, NTSC

or PAL.

• USB: select MSDC to use this camera as a removable disk, or

PC CAM to use as a webcam.

• Start-up image: select this option to set your favorite picture as a start-up image by choosing

“My Image”. Choose “System” for the default image, or turn the function off.

• Format: see page 15.

• Reset all: select this option to reset the entire menu and button operations to the original

factory settings.

Protecting indicator

Voice memo indicator

The format of the le

Movie clips

Audio les

The sequence of current le/

The total number of recorded le

Date and time stamp

(Only still image)

Playback mode

26

ENGLISH

3. During playback, use the Right key to fast-forward and the Left key to rewind.

Viewing thumbnails

In playback mode, press the W button to view les as thumbnails and use the Up, Down, Left

and Right keys to select a le. Press OK or the T key to view the le in full screen.

Locking les

1. In playback mode, press the Menu key and select Lock, then press OK.

2. Use the Up and Down keys to choose an item from the menu:

“Lock / Unlock one” – current le

“Lock All”, “Unlock All” – locks or unlocks all les

3. Press OK to conrm.

4. Press Menu to close.

Note: Once a le is locked this icon will be displayed on the screen. Locked les cannot

be deleted.

Deleting les

1. In playback mode, press the Menu key and select the Delete menu.

2. Press OK to enter the menu, then select “One” to delete the current le or “All” to delete all

except locked les.

3. Use the Right and Left keys to select the item to be deleted.

4. Press OK to conrm, and a dialog box will appear. Use the Up or Down keys to select “Yes”.

5. Press OK to delete.

Hot key: press the Delete key in playback mode to delete the le quickly.

Play a slide show

1. In playback mode, press the Menu key and select the Slide Show menu.

2. Use the Up and Down keys to select les for slide show.

3. Set the time between each slide by selecting “Interval” and pressing Left or Right keys to

choose time from 1 to 10 seconds.

4. Press “Start” to prepare les, then OK to start slide show.

1. Press Menu key to end.

Adding effects

1. In playback mode, press the Menu key and select the Effect menu.

2. Press OK to enter the menu, then use the Up and Down keys to choose the effect: B&W,

Sepia, Negative, Red, Green, Blue, Binarize, Sunset, Warm, Cold, Contrast.

3. Press OK to apply the effect.

Rotating the image

1. In playback mode, select the image you wish to rotate.

2. Press the Menu key, select the Rotate menu, then press OK.

3. Choose “Rotate” to rotate the image 90 degrees, then press “Save” to store.

4. Press “Back” to return to the Rotate menu.

CONNECTIONS

Connecting the video camera to a television

1. Connect the camera and the TV using the supplied cable, and power on both. When the

video camera’s screen turns black, the TV is performing as its monitor.

2. Set the TV to “AV”.

3. Set the video camera to record mode to preview anything you want to record on the

TV screen.

4. Set the camera to playback mode to review pictures, video and audio clips via the TV.

Connecting the camera to a PC

There are two ways to download your les to a computer:

1. By inserting the memory card into a card reader.

27

ENGLISH

3. During playback, use the Right key to fast-forward and the Left key to rewind.

Viewing thumbnails

In playback mode, press the W button to view les as thumbnails and use the Up, Down, Left

and Right keys to select a le. Press OK or the T key to view the le in full screen.

Locking les

1. In playback mode, press the Menu key and select Lock, then press OK.

2. Use the Up and Down keys to choose an item from the menu:

“Lock / Unlock one” – current le

“Lock All”, “Unlock All” – locks or unlocks all les

3. Press OK to conrm.

4. Press Menu to close.

Note: Once a le is locked this icon will be displayed on the screen. Locked les cannot

be deleted.

Deleting les

1. In playback mode, press the Menu key and select the Delete menu.

2. Press OK to enter the menu, then select “One” to delete the current le or “All” to delete all

except locked les.

3. Use the Right and Left keys to select the item to be deleted.

4. Press OK to conrm, and a dialog box will appear. Use the Up or Down keys to select “Yes”.

5. Press OK to delete.

Hot key: press the Delete key in playback mode to delete the le quickly.

Play a slide show

1. In playback mode, press the Menu key and select the Slide Show menu.

2. Use the Up and Down keys to select les for slide show.

3. Set the time between each slide by selecting “Interval” and pressing Left or Right keys to

choose time from 1 to 10 seconds.

4. Press “Start” to prepare les, then OK to start slide show.

1. Press Menu key to end.

Adding effects

1. In playback mode, press the Menu key and select the Effect menu.

2. Press OK to enter the menu, then use the Up and Down keys to choose the effect: B&W,

Sepia, Negative, Red, Green, Blue, Binarize, Sunset, Warm, Cold, Contrast.

3. Press OK to apply the effect.

Rotating the image

1. In playback mode, select the image you wish to rotate.

2. Press the Menu key, select the Rotate menu, then press OK.

3. Choose “Rotate” to rotate the image 90 degrees, then press “Save” to store.

4. Press “Back” to return to the Rotate menu.

Resizing an image

1. Select the image to be resized.

2. In playback mode, press the Menu key then choose the Resize menu. Press OK.

3. Use the Up or Down keys to choose the required size: 2048x1536, 1280x960, 640x480.

4. Press OK to save the resized image.

Note: The image can only be resized at a smaller size.

Adding a voice memo

1. In playback mode, select the image.

2. Press the Menu key, then choose the Voice Memo menu. Press

OK to display dialog box (see illustration).

3. Select “Add” then press OK to start recording the voice memo.

4. Press the Shutter button to end the recording.

Setting a start-up image

1. In playback mode, select an image.

2. Press the Menu key and select the Start-up Image menu. Press OK.

3. Use the Up and Down keys to select “Set” or “Cancel”, then press OK to conrm.

4. Set “Start-up Image” in the Setup menu to “My Image” mode.

CONNECTIONS

Connecting the video camera to a television

1. Connect the camera and the TV using the supplied cable, and power on both. When the

video camera’s screen turns black, the TV is performing as its monitor.

2. Set the TV to “AV”.

3. Set the video camera to record mode to preview anything you want to record on the

TV screen.

4. Set the camera to playback mode to review pictures, video and audio clips via the TV.

Connecting the camera to a PC

There are two ways to download your les to a computer:

1. By inserting the memory card into a card reader.

28

ENGLISH

INSTALLING THE VIDEO SOFTWARE (Magix Video easy SE)

INSTALLING THE PHOTO SOFTWARE (Magix Photo Manager 10)

1. Insert the CD Software (included) in your CD-ROM drive.

2. In the main menu, click “Install MAGIX Video easy SE” and wait during the extraction.

3. Follow the onscreen instructions and press “Install” to begin the installation.

4. To launch “Magix Video easy SE” double clik on the shortcut.

System requirements:Intel® Pentium 4 or AMD® Athlon® 1 GHz and higher, 512 MB RAM,

400 MB free hard disk memory and a DVD drive for program installation, graphics card with a

screen resolution of at least 1024 x 768, sound card.

1. Insert the CD Software (included) into your CD-ROM drive.

2. In the main menu, click “Install MAGIX Photo Manager 10” and wait during the extraction.

3. Select your language and click “OK”.

4. “The MAGIX Photo Manager 10 conguration” window displays. Follow the onscreen

instructions and press “Install” to begin the installation.

5. Once you have nished installing, the “MAGIX Photo Manager 10” shortcut will appear on the

desk of your computer.

6. To start using “MAGIX Photo Manager 10”, double click on the shortcut. The pictures taken

with the camera automatically appear on the home screen. System requirements (minimum

conguration): Microsoft® Windows® 2000 XP I Vista® I 7. PC with Intel® Pentium® or AMD®

2. By connecting the camera via a USB cable (supplied).

Using a card reader

1. Eject the memory card from the video camera and insert into a card reader connected

to a computer.

2. Open “My Computer” or Windows Explorer and double-click the removable disk icon

that represents the card reader.

3. Copy images from the card onto your computer.

Using a USB cable

1. Set the USB to MSDC mode.

2. Connect the unit to your computer using the USB cable provided and double click the

“My Computer” icon on your desktop.

3. Double click the icon, then open the DCIM folder, and the 100MEDIA subfolder.

4. Copy all les into any directory you choose on your computer.

Note: Do not remove the memory card or the batteries while the les are being copied or

you risk destroying the les.

DOWNLOADING YOUR PHOTOS

29

ENGLISH

INSTALLING THE VIDEO SOFTWARE (Magix Video easy SE)

INSTALLING THE PHOTO SOFTWARE (Magix Photo Manager 10)

1. Insert the CD Software (included) into your CD-ROM drive.

2. In the main menu, click “Install MAGIX Photo Manager 10” and wait during the extraction.

3. Select your language and click “OK”.

4. “The MAGIX Photo Manager 10 conguration” window displays. Follow the onscreen

instructions and press “Install” to begin the installation.

5. Once you have nished installing, the “MAGIX Photo Manager 10” shortcut will appear on the

desk of your computer.

6. To start using “MAGIX Photo Manager 10”, double click on the shortcut. The pictures taken

with the camera automatically appear on the home screen. System requirements (minimum

conguration): Microsoft® Windows® 2000 XP I Vista® I 7. PC with Intel® Pentium® or AMD®

2. By connecting the camera via a USB cable (supplied).

Using a card reader

1. Eject the memory card from the video camera and insert into a card reader connected

to a computer.

2. Open “My Computer” or Windows Explorer and double-click the removable disk icon

that represents the card reader.

3. Copy images from the card onto your computer.

Using a USB cable

1. Set the USB to MSDC mode.

2. Connect the unit to your computer using the USB cable provided and double click the

“My Computer” icon on your desktop.

3. Double click the icon, then open the DCIM folder, and the 100MEDIA subfolder.

4. Copy all les into any directory you choose on your computer.

Note: Do not remove the memory card or the batteries while the les are being copied or

you risk destroying the les.

Using « Dual Mode Camera »

1. Connect the camera to a computer with the USB cable supplied.

2. On your desktop, open the folder “Dual Mode Camera”, and then double click “My Dsc”.

3. Download your photos and videos by clicking the icon. Then the photos and

videos stored in the camera’s built-in memory are displayed on the screen.

4. Select the photo(s) and video(s) you want to save. Click the icon to select them all,

or click directly the photo(s)/video(s) of your choice (a red frame will appear around each

photo/video) if you don’t want to save them all.

5. Save the selected photo(s) and video(s) by clicking the icon. Then choose a name

and a location for the folder in which the selected photo(s) and video(s) will be saved.

Using « MAGIX Photo Manager »

Once you have saved your photo(s) and video(s) in your computer, you can use “MAGIX

Photo Manager” to display them, numerize them, print them, create albums…

1. Connect the camera to a computer with the USB cable supplied.

2. On your desktop, double click on the “MAGIX Photo Manager 10” shortcut.

3. Reach the photos and videos by selecting the location where they have been saved.

4. According to what you want to do, follow the corresponding software’s instructions.

Publishing your photos on social networking sites:

1. Using “Magix Photo Manager 10”, select the photo that you wish to publish on Facebook or Flickr.

2. The selected image appears in an orange frame.

3. In the menu bar, click the “Online” tab and select “Upload media to other web services” and

then either “Upload media to Flickr” or “Upload media to Facebook”. 4. The “Upload” window will

be displayed on screen. Fill in the various elds (le name, description, key words, etc.).

5. Click “Upload” to conrm.

6. Depending on your upload destination, you will either open the Facebook or the Flickr home page.

7. Next follow in the instructions displayed on the screen to nish uploading.

DOWNLOADING YOUR PHOTOS

Athlon® 700 MHz or higher, 256 MB RAM, 120 MB hard disk space for program les, SVGA

graphics card with min. 4 MB RAM, (min. resolution 1024 x 600, 16-bit high-color), Microsoft®

compatible mouse.

Note: To enjoy unlimited use of “MAGIX Photo Manager 10” and “MAGIX Video easy SE”, you

need to register rst.

30

ENGLISH

MAINTENANCE

Only use a soft, slightly damp cloth to clean the unit. Do not use detergent. Do not expose

the unit to direct sunlight or any other heat source. Do not immerse the unit in water. Do not

dismantle or drop the unit. Do not try to twist or bend the unit.

WEBCAM MODE

Connected to your computer (not compatible with Apple MACs), your video camera can be used

as a webcam.

Webcam mode

1. Connect the video camera to your computer using the USB cable provided. Turn on the

camera and PC CAM or MSDC will appear on the LCD screen to indicate it is correctly

connected to the computer.

2. Use the Mode key to select PC CAM and double click the icon on your computer’s desk to

run the AMCAP program. If this is the rst time this function has been used, click “Preview”

(see illustration).

3. The video camera is now operating as a webcam. To change the image size, select Video

Capture Pin and increase the output size.

Instant messaging (chat)

You can use your camera as a webcam with your instant messaging client (Yahoo Messenger,

MSN Messenger, Skype…).

WARRANTY

NOTE: Please keep this instruction manual, it contains important information. This product

is covered by our two-years warranty. To make use of the warranty or the after-sales service,

please contact your retailer and supply proof of purchase. Our warranty covers material or

installation-related defects attributable to the manufacturer, with the exception of wear caused

by failure to respect the instructions for use or any unauthorised work on the equipment (such

as dismantling, exposure to heat or damp, etc).

Reference: DJ290SW

Designed in Europe – Made in China

©Lexibook®

www.lexibook.com

United Kingdom & Ireland

For any further information, please call Helpline: 0808 1003015

Environmental Protection

Unwanted electrical appliances can be recycled and should not be discarded along with

regular household waste! Please actively support the conservation of resources and help

protect the environment by returning this appliance to a collection centre (if available).

This product is not a toy.

Page is loading ...

Lexibook Move Cam DJ-290SW Owner's manual

This manual is also suitable for

Lexibook Move Cam DJ-290SW Owner's manual

in other languages

Related papers

Other documents