Shimano SM-JC40 Dealer's Manual

(English)

DM-R9150-08

DURA-ACE

SW-R9150

SW-R9160

SW-R610

ST-R9150

ST-R9160

ST-R9170

ST-R9180

FD-R9150

RD-R9150

BR-R9170

SM-EW90-A

SM-EW90-B

EW-RS910

EW-WU111

EW-SD50

EW-SD50-I

EW-JC130

SM-EWC2

SM-JC40

SM-JC41

SM-BTR1

BT-DN110

BT-DN110-A

BM-DN100

SM-BA01

SM-BCR1

SM-BCR2

SM-BCC1

SM-RT900

Dealer's Manual

ROAD MTB Trekking

City Touring/

Comfort Bike

URBAN SPORT E-BIKE

R9150 series

2

CONTENTS

IMPORTANT NOTICE .............................................................................................. 5

TO ENSURE SAFETY ............................................................................................... 6

LIST OF TOOLS TO BE USED ................................................................................ 20

INSTALLATION ..................................................................................................... 22

Electric wire wiring diagram (overall conceptual diagram) ....................................................................22

Electric wire wiring diagram (junction A side) .........................................................................................25

Using the Shimano original tool TL-EW02 ................................................................................................33

Installation of the dual control lever and brake cable ............................................................................34

Installation of the front derailleur ............................................................................................................ 39

Installation of the rear derailleur ..............................................................................................................44

Direct mount type ......................................................................................................................................45

Installing the shifting switch .....................................................................................................................46

Installation of junction A (SM-EW90-A/B) ................................................................................................54

Installation of junction A (EW-RS910) ....................................................................................................... 55

Installation of junction B ...........................................................................................................................60

Points to check before attaching the wireless unit (EW-WU111) ...........................................................61

Attaching the wireless unit (EW-WU111) .................................................................................................62

Installing the battery .................................................................................................................................65

3

INSTALLATION OF HYDRAULIC DISC BRAKE SYSTEM ....................................... 71

List of tools to be used when installing hydraulic disc brake system .....................................................71

Installation of the disc brake rotor ...........................................................................................................72

Installation of the brake hose ...................................................................................................................72

Installation of the brake hose (easy hose joint system) ........................................................................... 78

Installation to the handlebar ..................................................................................................................100

Adding Shimano genuine mineral oil and bleeding air ........................................................................103

Installing the brake caliper ...................................................................................................................... 119

Temporary tightening of the frame ﬁxing bolts ....................................................................................127

CONNECTION OF ELECTRIC WIRES ................................................................... 129

Connection of junction A ........................................................................................................................129

Connection of junction B ......................................................................................................................... 131

Connecting to the dual control lever ......................................................................................................137

Routing junction B and the electric wires inside the frame ..................................................................139

Assembly of the bottom bracket .............................................................................................................140

Installation of grommets .........................................................................................................................141

Checking connections ..............................................................................................................................142

Disconnection of the electric wires .........................................................................................................143

HOW TO OPERATE ............................................................................................ 146

Gear position control ...............................................................................................................................146

ADJUSTMENT .................................................................................................... 148

Adjustment of the rear derailleur ........................................................................................................... 148

Installing the chain ...................................................................................................................................153

Adjustment of the front derailleur .........................................................................................................153

Adjustment of lever stroke ...................................................................................................................... 163

Free stroke adjustment (ST-R9170) ..........................................................................................................166

4

CHARGING THE BATTERY .................................................................................. 168

Names of parts .........................................................................................................................................168

Charging method .....................................................................................................................................170

When charging is not possible ................................................................................................................172

CONNECTION AND COMMUNICATION WITH DEVICES ................................... 175

Settings customizable in E-TUBE PROJECT .............................................................................................175

MAINTENANCE .................................................................................................. 178

Replacing the bracket cover ....................................................................................................................178

Disassembly of the bracket body and lever body (ST-R9150) ................................................................179

Assembly of the switch unit ....................................................................................................................180

Assembly of the bracket body and lever body ....................................................................................... 182

Replacement of the pulley ......................................................................................................................183

Replacement of the plate and the plate tension spring ........................................................................184

Replacing the brake pads ........................................................................................................................186

Shimano genuine mineral oil replacement ............................................................................................187

5

IMPORTANT NOTICE

•

This dealer’s manual is intended primarily for use by professional bicycle mechanics.

Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the dealer’s manuals.

If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your place of purchase or a local

bicycle dealer for their assistance.

•

Make sure to read all instruction manuals included with the product.

•

Do not disassemble or modify the product other than as stated in the information contained in this dealer’s manual.

•

All manuals and technical documents are accessible online at https://si.shimano.com.

•

For consumers who do not have easy access to the internet, please contact a SHIMANO distributor or any of the SHIMANO ofﬁces to obtain a hardcopy

of the User's Manual.

•

Please observe the appropriate rules and regulations of the country, state or region in which you conduct your business as a dealer.

•

The Bluetooth

®

word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by SHIMANO INC. is under

license.

Other trademarks and trade names are those of their respective owners.

For safety, be sure to read this dealer’s manual thoroughly before use, and follow it for correct use.

The following instructions must be observed at all times in order to prevent personal injury and physical damage to equipment and surroundings.

The instructions are classiﬁed according to the degree of danger or damage which may occur if the product is used incorrectly.

DANGER

Failure to follow the instructions will result in death or serious injury.

WARNING

Failure to follow the instructions could result in death or serious injury.

CAUTION

Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.

6

TO ENSURE SAFETY

DANGER

Be sure to also inform users of the following:



Lithium ion battery

Be sure to observe the following instructions in order to avoid burns or other injury from ﬂuid leakage, overheating, ﬁre, or explosion.

•

Use the designated charger to charge the battery. If any non-speciﬁed items are used, ﬁre, overheating or leakage may occur.

•

Do not heat the battery or throw it into ﬁre. If this is not observed, ﬁre or bursting may occur.

•

Do not deform, modify, disassemble or apply solder directly to the battery. Do not leave the battery in places which may exceed 60°C in temperature,

such as places which are exposed to direct sunlight inside vehicles on hot days or near stoves. If this is not observed, leakages, overheating or bursting

may cause ﬁre, burns, or other injuries.

•

Do not connect the (+) and (-) terminals with metallic objects. Do not carry or store the battery together with metallic objects such as necklaces or

hairpins. If this is not observed, short-circuits, overheating, burns or other injury may occur.

•

If any liquid leaking from the battery gets into the eyes, immediately wash the affected area with clean water without rubbing the eyes, and then

seek medical attention.



Battery charger/Battery charger cord

Be sure to observe the following instructions in order to avoid burns or other injury from ﬂuid leakage, overheating, ﬁre, or explosion.

•

Do not get the charger wet or use it while it is wet, and do not touch or hold it with wet hands. If this is not observed, problems with operation or

electric shocks may occur.

•

Do not cover the charger with cloths while it is in use. If this is not observed, heat may build up and the case may become deformed, or ﬁre or

overheating may occur.

•

Do not disassemble or modify the charger. If this is not observed, electric shocks or injury may occur.

•

Use the charger at the speciﬁed power supply voltage only. If a power supply voltage other than that speciﬁed is used, ﬁre, explosions, smoke,

overheating, electric shocks or burns may occur.

•

Do not touch metallic parts of the charger or the AC adapter if there is a lighting storm. If lightning strikes, electric shocks may occur.



SM-BCR2: Battery charger for SM-BTR2/BT-DN110/BT-DN110-A

•

Use an AC adapter with a USB port with a voltage of 5.0 V DC and with a current equal to or higher than 1.0 A DC. If the one with a current lower

than 1.0 A is used, the AC adapter may heat up, potentially causing a ﬁre, smoke, overheating, destruction, electric shock, or burns.

7

TO ENSURE SAFETY

WARNING

•

Be sure to follow the instructions provided in the manuals when installing the product.

It is recommended that you use SHIMANO genuine parts. If parts such as screws and nuts become loose or damaged, the bicycle may suddenly fall over,

which may cause serious injury.

•

Wear approved eye protection while performing maintenance tasks such as replacing components.

•

This dealer’s manual is for use with the DURA-ACE R9150 series (electronic gear shifting system) only.

For information on products not covered in this manual, please look up the model on the website (https://si.shimano.com).

Be sure to also inform users of the following:

•

Never use alkali based or acid based solvents, such as rust cleaners. If those solvents are used the chain might break and cause serious injury.

Intervals between maintenance depend on the use and riding circumstances. Clean the chain with an appropriate chain cleaner regularly.

•

Check that the wheels are fastened securely before riding the bicycle. If the wheels are loose in any way, they may come off the bicycle and cause

serious injury.

•

Check the chain for any damage (deformation or crack), skipping, or other abnormalities such as unintended gear shifting. The chain may break, and

you may fall. If any problems are found, consult a dealer or an agency.

•

Be careful not to let the hemming of your clothes get caught in the chain while riding. Otherwise you may fall off the bicycle.

8

TO ENSURE SAFETY



About the multi-shift function

•

On this system, the multi-shift function can be conﬁgured using E-TUBE PROJECT. The gears will continue to shift when the shifting switch is pressed

using the multi-shift function. Shifting speed setting for multi-shift can also be modiﬁed. When modifying the gear changing settings for multi-shift,

carefully read "Settings customizable in E-TUBE PROJECT" in this dealer's manual.

•

Be careful when crank revolutions are set to low with a faster setting of the multi-shifting speed. The chain will be unable to follow the movement of

the rear derailleur, possibly leading to issues such as the chain slipping over the tip of the cassette sprocket teeth, the cassette sprocket deforming, or

the chain breaking.

Item Multi-shift speed Characteristics Usage notes

Crank rotation speed when

operating multi-shift

Very fast

High speed

Quick multi-shifting is possible

•

The crank rotation speed can be

adjusted quickly depending on

changes in riding conditions.

•

The speed can be adjusted

quickly.

•

Over-shifting occurs easily.

•

If the rotation speed of the

crank is low, the chain will be

unable to follow the movement

of the rear derailleur.

The chain may therefore slip

over the tip of the cassette

sprocket teeth.

High crank rotation speed

Fast

Normal Default setting

Slow

Very slow Low speed Accurate multi-shifting is possible Multi-shifting takes some time

By default it is set to Normal.

Fully understand the features of the multi-shift speed, and choose a multi-shift gear shifting setting according to the riding conditions (terrain, riding

method, etc.).

9

TO ENSURE SAFETY



Lithium ion battery

•

Do not place the battery into fresh water or sea water, and do not allow the battery terminals to get wet. If this is not observed, ﬁre, bursting or

overheating may occur.

•

Do not use the battery if it has any noticeable scratches or other external damage. If this is not observed, bursting, overheating or problems with

operation may occur.

•

Do not throw or subject the battery to strong shock. If this is not observed, bursting, overheating or problems with operation may occur.

•

Do not use the battery if leakages, discoloration, deformation or any other abnormalities occur. If this is not observed, bursting, overheating or

problems with operation may occur.

•

If any leaked ﬂuid gets on your skin or clothes, wash it off immediately with clean water. The leaked ﬂuid may damage your skin.

•

Do not use it outside these operating temperature ranges of the battery. If the battery is used or stored in temperatures which are outside these

ranges, ﬁre, injury or problems with operation may occur. The operating temperature ranges for the battery are given below.

1. During discharge: –10°C - 50°C

2. During charging: 0°C - 45°C

SM-BTR1: Lithium ion battery (external type)

•

If charging is not complete after 1.5 hours, stop charging. If this is not observed, ﬁre, bursting or overheating may occur.

SM-BTR2/BT-DN110/BT-DN110-A: Lithium ion battery (built-in type)

•

If the battery does not become fully charged after 4 hours, stop charging. If this is not observed, ﬁre, bursting or overheating may occur.



Battery charger/Battery charger cord

SM-BCR1: Battery charger for SM-BTR1

•

Hold the power plug when connecting or disconnecting the plug. Failure to do so may cause a ﬁre or electric shock.

•

If the following occurs, stop using the device and contact a dealer. A ﬁre or electric shock may occur.

*

If heat or acrid-smelling smoke is coming out from the power plug.

*

There may be a bad connection inside the power plug.

•

Do not overload the electrical outlet with appliances beyond its rated capacity, and use only a 100 - 240 V AC electrical outlet. If the electrical outlet is

overloaded by connecting too many appliances using adapters, overheating resulting in ﬁre may occur.

•

Do not damage the power cord or power plug. (Do not damage, process, let near hot objects, bend, twist or pull them; do not place heavy objects on

top or bundle them tightly.) If they are used while damaged, ﬁre, electric shocks or short-circuits may occur.

•

Do not use the battery charger with commercially-available electrical transformers designed for overseas use (travel converters). They may damage the

battery charger.

•

Always be sure to insert the power plug as far as it will go. If this is not observed, ﬁre may occur.

SM-BCR2: Battery charger for SM-BTR2/BT-DN110/BT-DN110-A

•

Do not use any USB cable other than the USB cable which is supplied with the PC linkage device. This may cause a charging error, ﬁre, or failure to

connect to PC due to overheating.

•

Do not connect the charger to PC when it is on standby. This may cause a PC failure depending on its speciﬁcations.

•

When connecting or disconnecting the USB cable or the charger, be sure to hold the cable by the plug. Failure to do so may cause a ﬁre or electric

shock. If the following occurs, stop using the device and contact a dealer. A ﬁre or electric shock may occur.

*

If heat or acrid-smelling smoke is coming out from the power plug.

*

There may be a bad connection inside the power plug.

•

If it thunders while charging with an AC adapter with a USB port, do not touch the device, bicycle, or the AC adapter. If lightning strikes, electric

shocks may occur.

•

Use an AC adapter with a USB port with a voltage of 5.0 V DC and with a current equal to or higher than 1.0 A DC. If the one with a current lower

than 1.0 A DC is used, a charge error may occur or the AC adapter may heat up, leading to a ﬁre.

•

Do not use a USB hub when connecting the cable to a computer USB port. This may cause a charging error or ﬁre due to overheating.

•

Be careful not to damage the charging cable. (Do not damage, process, let near hot objects, bend, twist or pull them; do not place heavy objects on

top or bundle them tightly.) If they are used while damaged, ﬁre, electric shocks or short-circuits may occur.

10

TO ENSURE SAFETY



Brake

•

Because each bicycle may handle slightly differently depending on the model, be sure to learn the proper braking technique (including brake lever

pressure and bicycle control characteristics) and operation of your bicycle. Improper use of your bicycle's brake system may result in a loss of control or

a fall, which could lead to severe injury.

•

Do not apply the front brake too strongly. If you do so, the front wheel may lock and the bicycle may fall forward, and serious injury may result.

•

Because the required braking distance will be longer during wet weather, reduce your speed and apply the brakes early and gently. You may fall or

collide and be seriously injured.

•

A wet road surface may cause tires to skid; therefore, to avoid this, reduce your speed and apply the brakes early and gently. If the tires skid, you may

fall and be seriously injured.



Hydraulic disc brake

•

Please use extra caution to keep your ﬁngers away from the rotating disc brake rotor. The disc brake rotor is sharp

enough to inﬂict severe injury to your ﬁngers if caught within the openings of moving rotor.

•

Do not touch the calipers and disc brake rotor while riding or immediately after dismounting from the bicycle. The calipers and disc brake rotor will

become hot when the brakes are operated, so you may get burned if you touch them.

•

Be careful not to allow any oil or grease to get onto the disc brake rotor and brake pads. Riding the bicycle with oil or grease on the disc brake rotor

and brake pads may prevent the brakes from operating and result in serious injury due to a fall or collision.

•

Check the thickness of the brake pads and do not use them if they have a thickness of 0.5 mm or less. Doing so may

prevent the brakes from operating and result in serious injury.

2 mm 0.5 mm

•

Do not use the disc brake rotor if it is cracked or deformed. The disc brake rotor may break, and result in serious injury due to a fall.

•

Do not use the disc brake rotor if its thickness is 1.5 mm or less. Also do not use it if the aluminum surface becomes visible. The disc brake rotor may

break, and result in serious injury due to a fall.

•

Do not continuously apply the brakes. Doing so may cause a sudden increase in the brake lever stroke and prevent the brakes from operating and

result in serious injury.

•

Do not use the brakes with ﬂuid leaking. Doing so may prevent the brakes from operating and result in serious injury.

11

TO ENSURE SAFETY

For Installation to the Bicycle, and Maintenance:

•

When the shifting switch is operated, the motor which drives the front derailleur will operate to the shifting position without stopping, so be careful

not to get your ﬁngers caught.



Hydraulic disc brake

•

Please make sure to keep your ﬁngers away from the rotating disc brake rotor during installation or maintenance of the

wheel. The disc brake rotor is sharp enough to inﬂict severe injury to your ﬁngers if caught within the openings of

moving rotor.

•

Do not use the disc brake rotor if it is cracked or warped. The disc brake rotor may break, and result in serious injury due to a fall.

•

Do not use the disc brake rotor if its thickness is 1.5 mm or less. Also do not use it if the aluminum surface becomes visible. The disc brake rotor may

break, and result in serious injury due to a fall.

•

The calipers and disc brake rotor will become hot when the brakes are operated; do not touch them while riding or immediately after dismounting

from the bicycle. Otherwise, you may get burned.

•

Be careful not to allow any oil or grease to get onto the disc brake rotor and brake pads. Riding the bicycle in that state may prevent the brakes from

operating and result in serious injury due to a fall or collision.

•

Check the thickness of the brake pads and do not use them if they have a thickness of 0.5 mm or less. Doing so may prevent the brakes from operating

and result in serious injury.

•

Do not use oil other than SHIMANO genuine mineral oil. Doing so may prevent the brakes from operating and result in serious injury.

•

Be sure to use only oil from a freshly-opened container. Doing so may prevent the brakes from operating and result in serious injury.

•

Do not let water or air bubbles to get into the brake system. Doing so may prevent the brakes from operating and result in serious injury.

•

Do not use with a tandem bicycle. Doing so may prevent the brakes from operating and result in serious injury due to a fall or collision.

•

If the quick release lever is on the same side as the disc brake rotor, check that it does not interfere with the disc brake rotor.

•

When installing the brake caliper using bolt ﬁxing pins, be sure to use mounting bolts of the

appropriate length.

If not, the bolt ﬁxing pins may not be securely fastened, and the bolts may fall out.

Bolt ﬁxing pin



Brake hose

•

Refer to the table below, and do not use an incorrect connector insert. Doing so may prevent the brakes from operating and result in serious injury.

Model No.

Connector insert

Length Color

SM-BH90-JK-SSR 11.2 mm Silver

•

Do not reuse the olive piece or the connector insert when reinstalling. Doing so may prevent the brakes from operating and result in serious injury due

to a fall.

Brake hose

Connecting bolt

Olive

Cut end

Connector insert

12

TO ENSURE SAFETY

•

Cut the brake hose so that the cut end is perpendicular to the length of the hose. If the brake hose is cut at an angle, ﬂuid leaks may result.

90°



Points to note about the handlebars

•

Note the speciﬁcations for compatible handlebars.

ST-R9160/ST-R9180/SW-R9160

•

Handle inner diameter: Ø19.0 - 22.5 mm

•

Handle outer diameter: Ø22.2 - 24.0 mm

•

Applicable handlebars: Carbon ﬁber handlebars (with aluminum inserts where the brake levers are installed) or aluminum handlebars.

*

Carbon ﬁber handlebars without aluminum inserts, where the brake levers are installed, cannot be used.

EW-RS910 (Built-in bar end type)

•

Handle inner diameter: Ø20.5 - 21.5 mm

•

Handle outer diameter: Ø23.8 - 24.2 mm

13

TO ENSURE SAFETY

CAUTION

Be sure to also inform users of the following:



Lithium ion battery

•

Store the battery in a safe place away from the reach of infants and pets.

SM-BTR1: Lithium ion battery (external type)

•

When you do not use the battery for a long period, remove and charge the battery before storage.

SM-BTR2/BT-DN110/BT-DN110-A: Lithium ion battery (built-in type)

•

When you do not use the battery for a long period, charge the battery before storage.



Battery charger/Battery charger cord

SM-BCR1: Battery charger for SM-BTR1

•

Disconnect the power plug from the electrical outlet before cleaning the charger.

SM-BCR2: Battery charger for SM-BTR2/BT-DN110/BT-DN110-A

•

Disconnect the USB cable or the charging cable when performing maintenance.



Hydraulic disc brake

Cautions on SHIMANO genuine mineral oil

•

In the event of eye contact, ﬂush with fresh water and seek medical assistance immediately. Contact with eyes may result in irritation.

•

In the event of skin contact, wash well with soap and water. Contact with eyes may result in irritation.

•

Cover nose and mouth with a respirator type mask and use in a well ventilated area.

Inhalation of mineral oil mist or vapors may cause nausea. If mineral oil mist or vapor is inhaled, go immediately to an area with fresh air. Cover up

with a blanket. Stay warm and stable and seek professional medical advice.

Burn-in period

•

Disc brakes have a burn-in period, and the braking force will gradually increase as the burn-in period progresses. Make sure that you are aware of any

such increases in braking force when using the brakes during the burn-in period.

The same thing will happen when the brake pads or disc brake rotor are replaced.

For Installation to the Bicycle, and Maintenance:



Hydraulic disc brake

Handling SHIMANO genuine mineral oil

•

Use safety glasses when handling, and avoid contact with eyes. In the event of eye contact, ﬂush with fresh water and seek medical assistance

immediately. Contact with eyes may result in irritation.

•

Use gloves when handling. In the event of skin contact, wash well with soap and water. Contact with eyes may result in irritation.

•

Do not drink. May cause vomiting or diarrhea.

•

Keep out of reach of children.

•

Do not cut, let near heat, weld or pressurize the SHIMANO genuine mineral oil container. Doing so may cause an explosion or ﬁre.

•

Disposal of Used Oil: Follow local county and/or state codes for disposal. Use caution when preparing the oil for disposal.

•

Directions: Keep the container sealed to prevent foreign objects and moisture from getting inside, and store it in a cool, dark area away from direct

sunlight or heat. Keep from heat or ﬂame, Petroleum Class III, Danger level III

Brake hose

•

When cutting the brake hose, handle the knife carefully so as not to cause injury.

•

Be careful to avoid injury from the olive.

14

TO ENSURE SAFETY

NOTICE

Be sure to also inform users of the following:

•

Be sure to rotate the crank when carrying out any operations which are related to gear shifting.

•

Do not keep connecting and disconnecting the small waterproof connector. It may impair the function.

•

Be careful not to get water into the E-TUBE port.

•

The components are designed to be fully waterproofed to withstand wet weather riding conditions; however, do not deliberately place them into

water.

•

Do not clean the bicycle with a high-pressure washer. If water gets into any of the components, operating problems or rusting may result.

•

Be sure to keep turning the crank during the gear shifting.

•

Handle the product carefully, and avoid subjecting it to any strong shocks.

•

Do not use thinners or similar substances to clean the products. Such substances may damage the surfaces.

•

If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.

•

Keep away from magnetized objects. If this is not observed, the product may be damaged.

For products that have magnets attached, make sure to install the product, using the attached magnet, in the location that is speciﬁed.

•

Contact the place of purchase for updates of the component software. The most up-to-date information is available on the Shimano website.

•

Products are not guaranteed against natural wear and deterioration from normal use and aging.

•

For maximum performance we highly recommend Shimano lubricants and maintenance products.



Lithium ion battery

•

Lithium-ion batteries are recyclable, valuable resources.

For information on used batteries, contact the place of purchase or a bicycle dealer.

•

Charging can be carried out at any time regardless of the amount of charge remaining. Always be sure to use the special battery charger to charge the

battery until it is fully recharged.

•

The battery is not fully charged at the time of purchase. Before riding, be sure to fully charge the battery.

•

If the battery has become completely empty, charge it as soon as possible. If you leave the battery without charging it, it will cause the battery to

deteriorate.

•

The battery is an exhaustible item. The battery will gradually lose its capacity to charging after repeated use.

If the length of time that the battery can be used becomes extremely short, it has probably reached the end of its life, and so you will need to

purchase a new battery.

•

The life of the battery will vary depending on factors such as the storage method, the usage conditions, the surrounding environment and the

characteristics of the individual battery pack.

•

If storing the battery away for a long period, remove it when the battery level is 50% or higher or when the green indicator is illuminating in order to

prolong its useful life; and it is recommended that you charge the battery about every six months.

•

If the storage temperature is high, the performance of the battery is reduced, and its useable time will be shorter. When you use the battery after a

long storage period, store the battery indoors where the battery will not be exposed to direct sunlight or rain.

•

If the ambient temperature is low, the battery's usable time will be shorter.

SM-BTR1: Lithium ion battery (external type)

•

When storing the battery away, remove the battery from the bicycle and install the terminal cover ﬁrst.

•

The charging time is approximately 1.5 hours. (Note that the actual time will vary depending on the remaining battery charge.)

•

If the battery feels difﬁcult to insert or remove, apply speciﬁed grease (Premium Grease) to the part that touches the O-ring at the side.

SM-BTR2/BT-DN110/BT-DN110-A: Lithium ion battery (built-in type)

•

After removing the battery from the bicycle for storage, install a dummy plug.

•

The charging time of an AC adapter with a USB port is about 1.5 hours, and that of computer USB port type about 3 hours. (Note that the actual time

will vary depending on the amount of charge remaining in the battery. Depending on the speciﬁcations of the AC adapter, recharging via the AC

adapter may require as much time (about 3 hours) as recharging via PC.)

15

TO ENSURE SAFETY



Battery charger/Battery charger cord

•

Use this instrument under the direction of a safety supervisor or the direction for use. Do not allow physically, sensory, or mentally impaired persons,

inexperienced persons, or persons with no required knowledge, including children, to use this product.

•

Do not allow children to play near the product.

Disposal information for countries outside the European Union

This symbol is only valid within the European Union.

Contact the place of purchase or your nearest Shimano agent for advice on disposing.

•

Charge the battery indoors to avoid exposure to rain or wind.

•

Do not use outdoors or in environments with high humidity.

•

Do not place the battery charger on dusty ﬂoors when using it.

•

Place the battery charger on a stable surface such as a table when using it.

•

Do not place any objects on top of the battery charger or its cable.

•

Do not bundle the cables.

•

Do not hold the battery charger by the cables when carrying it.

•

Do not apply excessive tension to the cables.

•

Do not wash the battery charger or wipe it using detergents.

SM-BCR2: Battery charger/PC linkage device for SM-BTR2/BT-DN110/BT-DN110-A

•

Connect the PC linkage device directly to a computer, without using an intermediate device such as a USB hub.

•

Do not ride the bicycle while the PC linkage device and cable are still connected to it.

•

Do not connect two or more of the same units to the same connection point. If this is not done, the units may not operate correctly.

•

Do not connect or disconnect units again while unit recognition is in progress or after recognition is complete. If this is not done, the units may not

operate correctly.

Check the procedures which are given in the user's manual for the E-TUBE PROJECT when connecting and disconnecting units.

•

The tightness of the PC link cable will tend to drop after repeated connections and disconnections. If this happens, replace the cable.

•

Do not connect two or more PC linkage device at the same time. If two or more PC linkage device units are connected, they will not operate correctly.

In addition, the PC may need to be restarted if operating errors occur.

•

PC linkage devices cannot be used while the charger is connected.



Rear derailleur

•

If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.

•

If the chain keeps skipping, ask the place of purchase to replace the chainrings, sprockets and/or the chain.

•

If there is a large gap in the pulleys which causes a lot of noise, ask the place of purchase to replace the pulleys.

•

The gears should be periodically washed with a neutral detergent. In addition, cleaning the chain with neutral detergent and lubricating it can be an

effective way of extending the life of the gears and the chain.

•

If the amount of looseness in the links is so great that adjustment is not possible, you should replace the derailleur.



Hydraulic disc brake

•

When the bicycle wheel has been removed, it is recommended that pad spacers are installed. Do not depress the brake lever while the wheel is

removed. If the brake lever is depressed without the pad spacers installed, the pistons will protrude further than normal. If that happens, consult a

dealer.

•

Use soapy water and a dry cloth when cleaning and carrying out maintenance of the brake system. Do not use commercially available brake cleaners

or silencing agents, as they can cause damage to parts such as seals.

16

TO ENSURE SAFETY



Dual control lever

•

In the case of carbon levers, wash them with a soft cloth using a neutral detergent. Otherwise, the material may break down and be damaged.

•

Avoid leaving the carbon levers in areas of high temperature. Also keep them well away from ﬁre.



Wireless unit

•

When using EW-WU111, combine it with one of the following units.

External type: BM-DN100, Built-in type: BT-DN110/BT-DN110-A

•

Do not keep connecting and disconnecting the small waterproof connector. It may impair the function.

•

Be careful not to get water into the E-TUBE port.

•

The components are designed to be fully waterproofed to withstand wet weather riding conditions; however, do not deliberately place them into

water.

•

Do not clean the bicycle with a high-pressure wash. If water gets into any of the components, operating problems or rusting may result.

•

Handle the product carefully, and avoid subjecting it to any strong shocks.

•

Do not position the unit on the side of the bicycle frame, as in the illustrations.

If the bicycle collapses, damage to the unit may result if the unit is caught between the bicycle frame and curbstones etc.

•

Do not use thinners or similar substances to clean the products. Such substances may damage the surfaces.

•

Do not leave the product in an area exposed to strong sunlight for an extended period of time.

•

Do not disassemble the product as it cannot be reassembled.

•

When cleaning the product, use a cloth moistened with a diluted neutral detergent.

•

Contact the place of purchase for updates of the component software. The most up-to-date information is available on the Shimano website.

For Installation to the Bicycle, and Maintenance:

•

Be sure to attach dummy plugs to any unused E-TUBE ports.

•

Be sure to use Shimano original tool TL-EW02 to remove the electric wires.

•

The motors of the motor unit cannot be repaired.

•

Contact Shimano for information regarding the shipment of the battery charger to South Korea and Malaysia.

•

Use a brake hose/outer casing which still has some length to spare even when the handlebars are turned all the way to both sides.

Furthermore, check that the shifting lever does not touch the bicycle frame when the handlebars are turned all the way.

•

Use the speciﬁed cable for smooth operation.

•

The clamp band, clamp bolt, and clamp nut are not compatible with other products. Do not use with components that are used in other products.

17

TO ENSURE SAFETY



Electric wires/Electric wire covers

•

Secure the electric wires with a zip tie so that they do not interfere with the chainrings, sprockets or tires.

•

The strength of the adhesive is fairly weak to prevent the paint on the frame from being peeled off at when removing the electric wire cover, such as

when replacing the electric wires. If the electric wire cover is peeled off, replace it with a new one. When removing the electric wire cover, do not peel

it off too vigorously. If so, the paint on the frame will peel off, too.

•

Do not remove the wire holders which are attached to the built-in type electric wires (EW-SD50-I). The wire holders prevent the electric wires from

moving inside the frame.

•

When installing to the bicycle, do not forcibly bend the electric wire plug. It may result in a poor contact.



Rear derailleur

•

Always be sure to adjust the top adjustment bolt and the low adjustment bolt according to the instructions given in the adjustment section.

If these bolts are not adjusted, the chain may become clamped between the spokes and the largest sprocket and the wheel may lock, or the chain may

slip onto a smaller sprocket.

•

Periodically clean the derailleur and lubricate all moving parts (mechanism and pulleys).

•

If gear shifting adjustments cannot be carried out, check the degree of parallel of the rear dropouts.

•

The guide pulley and tension pulley are marked on one side with arrows to indicate the direction of rotation. When attaching the pulleys, make sure

to orient them so that the sides marked with arrows face toward the bicycle.



Hydraulic disc brake

•

If the brake caliper mounting boss and the dropout are not of standard dimensions, the disc brake rotor and caliper may touch.

•

When the bicycle wheel has been removed, it is recommended that pad spacers are installed. The pad spacers will prevent the piston from coming out

if the brake lever is depressed while the wheel is removed.

•

If the brake lever is depressed without the pad spacers installed, the pistons will protrude further than is normal. Use a slotted screwdriver or similar

tool to push back the brake pads, while being careful not to damage the surfaces of the brake pads. (If the brake pads are not installed, use a

ﬂat-shaped tool to push the pistons straight back in, while being careful not to damage them)

If it is difﬁcult to push the brake pads or pistons back, remove the bleed screws and then try again. (Note that some oil may overﬂow from the

reservoir tank at this time.)

•

Use isopropyl alcohol, soapy water or a dry cloth when cleaning and carrying out maintenance of the brake system. Do not use commercially available

brake cleaners or silencing agents. They can cause damage to parts such as seals.

•

Do not remove the pistons when disassembling the brake calipers.

•

If the disc brake rotor is worn, cracked or warped, it should be replaced.



Dual control lever

•

Dummy plugs are installed at the time of shipment from the factory. Do not remove them except when necessary.

•

When routing the electric wires, take care to ensure that they do not interfere with the brake levers.

The actual product may differ from the illustration because this manual is intended mainly to explain the procedures for using

the product.

18

TO ENSURE SAFETY

For Installation to the Bicycle:



Notes on reinstalling and replacing components

•

When the product is reassembled or replaced, it is automatically recognized by the system to allow operation according to the settings.

•

If the system does not operate after reassembly and replacement, follow the system power reset procedure below to check the operation.

•

If the component conﬁguration changes or malfunction is observed, use the E-TUBE PROJECT software to update the ﬁrmware of each component to

the latest version and perform a check again. Also make sure that the E-TUBE PROJECT software is the latest version. If the software is not the latest

version, the component compatibility or the product functions may not be available.

Be sure to also inform users of the following:



About used batteries

•

Lithium-ion batteries are recyclable, valuable resources.

For information on used batteries, contact the place of purchase or a bicycle dealer.



About system power reset

•

When the system fails to operate, it may be recovered by resetting the system power.

•

After the battery is removed, about one minute is usually required for the system power to reset.

In the case of using SM-BTR1

•

Remove the battery from the battery mount. After about one minute, install the battery.

In the case of using SM-BTR2/BT-DN110/BT-DN110-A

•

Disconnect the plug from SM-BTR2/BT-DN110/BT-DN110-A. After about one minute, insert the plug.



Connection and communication with PC

•

PC linkage devices can be used to connect a PC to the bicycle (system or components), and an E-TUBE PROJECT can be used to carry out tasks such as

customizing single components or the whole system and updating their ﬁrmware.

If your versions of E-TUBE PROJECT software and ﬁrmware for each component are not up to date there could be problems operating the bicycle.

Check the software version and update it to the latest one.

PC linkage device E-TUBE PROJECT Firmware

SM-BMR2/SM-BTR2

SM-PCE1/SM-BCR2 Version 3.2.0 or later

Version 3.0.0 or later

BT-DN110/BT-DN110-A/

BM-DN100

Version 4.0.0 or later



Connection and communication with smartphone or tablet

•

It is possible to customize single components or the system, and update ﬁrmware, using E-TUBE PROJECT for smartphones/tablets after connecting the

bicycle (system or components) to a smartphone or tablet via Bluetooth LE.

•

E-TUBE PROJECT: app for smartphones/tablets

•

Firmware: software inside each component

•

Disconnect Bluetooth LE when not using E-TUBE PROJECT for smartphones/tablets.

Using the wireless unit without disconnecting Bluetooth LE may result in high battery power consumption.

About compatibility with E-TUBE

•

For details on the compatibility and functional limitations of units, refer to the following website.

(https://e-tubeproject.shimano.com/guide/#guide_list)

LIST OF TOOLS TO BE USED

20

LIST OF TOOLS TO BE USED

The following tools are needed for installation, adjustment, and maintenance purposes.

Tool Tool Tool

2 mm hexagon wrench Screwdriver[#2] Soft face mallet

2.5 mm hexagon wrench

Slotted screwdriver

Blade width: 4.0 - 5.0 mm

Blade thickness: 0.5 - 0.6 mm

Utility knife

3 mm hexagon wrench Hexalobular[#5] Handlebar tape cutout tool

4 mm hexagon wrench Hexalobular[#10] TL-CT12

5 mm hexagon wrench Snap ring pliers TL-EW02

23 mm hub spanner Special E-ring removal tool

Page is loading ...

Shimano SM-JC40 Dealer's Manual

Shimano SM-JC40 Dealer's Manual

Related papers

Other documents