Assembly Instructions
Caution: You must read this before you proceed
CHAIR
CAUTION: This Chair is NOT a TOY.
Keep your child / children at bay during the assembly process of assembly.
For turning the Chair and to prevent damage to the Chair, 02 persons may be needed
to execute this action
Noble House Home Furnishings LLC
1
Label Picture Description QTY
A Backrest panel 1
B Seat Panel 1
C
Right Leg Panel
(with Leveler)
1
D
Left Leg Panel (with
Leveler)
1
E Leg Support Bar 1
Parts List
Noble House Home Furnishings LLC
2
Label Picture Description QTY
①
Bolt
(M8x55mm)
7
②
Bolt
(M8x25mm)
3
③
Screw
(M7x60mm)
3
④
Flat Washer
(M8/18x1.5mm)
3
⑤
Allen Key 2
Hardware
Assembly Preparation
Before Beginning Assembly:
Noble House Home Furnishings LLC
3
This Chair has multiple parts and may require up to 30 minutes to assemble. To give
you an overview of the Chair parts, the above picture is to help you put the various
parts into perspective. Please read through the instructions below to familiarise
yourself with the parts and steps before assembly.
Unpack and place all parts on a clean, non-marring surface.
Step 1
Overview
Assembly Steps
Leg Support Bar
(E)
Backrest Panel
(A)
Seat Panel
(B)
FRONT FACING
Right Leg Panel
(C)
Left Leg Panel
(D)
Noble House Home Furnishings LLC
4
Lay down Backrest Panel (A) then attach Seat Panel (B) to Backrest Panel (A) by
using Bolts (②), Flat Washer (④) and secure by Allen key (⑤).
Do not fully tighten the Botls.
Step 2
Step 3
Position housing of Left Leg Panel (D) into pre-fixed iron dowel on Seat Panel (B) as
picture above.
Step 3.1: Secure Left Leg Panel (D) to Seat Panel (B) by using Bolt (①) with Allen
Key (⑤)
Step 3.2: Secure Left Leg Panel (D) to Backrest Panel (A) by using Bolt (①) with
Allen Key (⑤)
Do not fully tighten the Bolts.
5
A
B
Step 3.1
Step 3.2
D
B
A
Iron Dowel
Noble House Home Furnishings LLC
5
With assistance from your adult partners, turn the pre-assembled part in step 3 to the
other side.
Align the Tenon of Leg Support Bar(E) into the Mortise of Left Leg Panel(D). Then
position Mortise of Right Leg Panel(D) onto Tenon of Leg Support Bar(E) as shown
above.
Repeat same process in step 3.1 and 3.2 to Secure Right Leg Panel(C) to Seat Panel
(B) and Backrest Panel (A).
Do not fully tighten all the Bolts
Step 4
A
E
C
D
B
5
Noble House Home Furnishings LLC
6
With assistance from your adult partners, turn the Chair back to normal flat ground.
Secure Left Leg Panel (D) to Leg Support Bar (E) by using Screw (③) with Allen Key
(⑤).
Repeat the same process to secure Right Leg Panel (C) to the remaining Leg
Support Bar (E).
Do not fully tighten the Screws.
Step 5
C
D
E
Noble House Home Furnishings LLC
7
Step 6
Stand the Chair up.
Place the Chair on a LEVEL surface.
Inspect it and make sure all parts are adequately connected.
Gently and gracefully, sit onto the Chair.
This pressure will help the Legs and Chair reach full alignment status.
Check for wobbles on a LEVEL surface.
If no wobbles are found proceed to tighten the Bolts and Screws in a sequential
manner, until evenly secured.
When tightening the Bolts and Screws tighten sequentially.
Do not tighten any Bolt or Screw fully and then move on towards the next one.
With assistance from your adult partners, adjust the Levellers to desired height to
avoid wobbles.
Step 7
Your Chair is ready for use
This Chair can be used on a flat, level surface
Adjust Pre-installed Levellers height for balance
Noble House Home Furnishings LLC
8
Noble House Home Furnishings LLC
9
/
