Aktakom APS-7315 User manual

www.tmatlantic.com

APS-7313/7315/7612

Table of Contents

SAFETY INSTRUCTION... .. .. .. ... .. .. .. .. .. .. .3

OVERVIEW... .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. 5

Models Introduction. . . . . . . . . . . . ........ .5

Main Characteristics....................5

Front and Rear Panel Overview........ . . . . . . . . 6

OPERATION . .. .. .. .. .. .. ... .. .. .. .. .. .. .. .. .10

Power Up.. .. .. ... .. .. .. .. .. .. ... 10

Output ON/OFF. .. .. .. .. .. .. ... .. .. 11

Beep ON/OFF.. .. .. ... .. .. .. .. .. .. 11

Panel Lock. .. .. .. .. .. ... .. .. .. .. .11

Output Parameters Setup .. .. .. .. .. .. .12

Save Setup . .. ... .. .. .. .. .. .. ... .12

Recall Setup. . .. .. .. ... .. .. .. .. .. .13

1

Safety Symbols . .. .. .. .. .. .. ... .. .. 3

General Introduction.. .. .. ... .. .. .. .. 4

AC Input . .. .. .. .. .. ... .. .. .. .. .. .4

Fuse Parameters .. .. .. ... .. .. .. .. .. 4

FRONT PANEL INTRODUCTION... .. .. .. .. ... .. ..6

Panel Overview . .. .. .. .. .. ... .. .. .. 6

Display. .. .. ... .. .. .. .. .. .. ... .. .6

Status Indication . .. .. .. .. .. .. ... .. .6

Storage Indication .. ... .. .. .. .. .. .. .7

Brief Introduction of Panel Buttons . .. .. .. 7

REAR PANEL INTRODUCTION . ... .. .. .. .. .. .. ..9

KORAD

KA3000/6000-Series User Manual

KORAD

KA3000/6000-Series User Manual

REMOTE CONTROL.. .. .. ... .. .. .. .. .. .. ... 14

Remote Control Setup.. .. ... .. .. .. .1 4

Remote control procedures.... .. ... .1 5

FAQ .. . .. .. ... .. .. .. .. .. .. ... .. . ... ... .. ..16

SPECIFICATIONS . ... .. .. .. ... .. .. .. ... . ..17

2

APS-7313

APS-7315

APS-7612

KORAD

KA3000/6000-Series User Manual

KORAD

KA3000/6000-Series User Manual

7

C.CC.C

C.VC.V

OUTOUT

M2M2

M3M3

M4M4

M5M5

M1M1

Indication of saving an d recalling 5 setups stored internally;

OUT is output indicator. If light on, there is voltage

output in the output terminal.

C.C is con stan t current indicator. Whe n power

sup ply is in the mod e of constan t cur ren t,

thi s ligh t is on .

OCP is OCP indicator. When overcurrent function

is turned on, indicator lights on.

C.V is constant voltage indicator. When powe r supply

is in the mode of constant voltage, this light is on.

M3

M2

M1

M4

MEMOR Y

Saves or recalls panel settings. For settings,

1 ~ 4 are available. For save / recall details,

see Pa ge 13.

Storage Indication

Brief Introduction of Panel Operation

RECALL/SAVE

OCP

<

>

OVP

LO CK

UNLOCK

ADJUST

Volgote /

Current

Front panel lock_out function. For details, see Page 11.

Over-Current protect on/off,. Pressing this key for

more than 2 secends will make beep ON On/OFF.

Over-votage Protect On/Off

Output On/Off。

Voltage-Current Setting Adjustment

Digit Selector Buttons

Selection Voltage / Current for Adjustment

Pressing the key, the volt indicator starts to

flicker; pressing it again, the ampere indicator

starts to flicker. Then turn the key ADJUST and

the settings of the setted voltage or current can

be adjusted.

POWER

On / Off main power. For power up sequence,

see Page 10.

+

-

Connects the ground (earth ) terminal.

outputs voltage and current.

BEEP

Off /ON

8

.

KORAD

KA3000/6000-Series User Manual

KORAD

KA3000/6000-Series User Manual

1 1

Output On / Off

Panel Operation Pressing the Output ke y to turn on output;

and the ke y LED also turns on. Pressing the

Output key again to turn off the output and

the key LED.

Note: If there are any of the following co nditions, the output will

automatica lly turn off.

1. OVP turns on and there are unusual OVP on the output terminal.

2. The se tting vo ltage is more than that of the OVP.

3. Recalling other se tups from the memory.

Beep On / Off

Panel Operation By default, the beep so und is enabled. To turn off

the beep, press the OCP(BEEP) key for 2 se conds.

A beep co mes out and the beep setting will be turned

off. To enable the beep, press the OCP(BEEP) ke y

again for 2 seconds.

Front Panel Lock

Panel operation

Press the LOCK key to lock the front panel key operation.

The key LED turns on. To unlock, press the LOCK key for

2 seconds.

1 2

Output Set

1. Connecti ng the load to the front port, CH 1 + / - .

2. Setting output voltage and cu rrent.

Press the key Voltage/Current selecti on to sw itch vo ltage adjustm ent

and cu rrent adjustm ent. Adjusti ng vo ltage and current with

Voltage / Current Adjustm ent knob. By default, the Voltage

and Current kn ob work in the co arse mode. To acti va te the

fine mode, press the ke ys to select the coarse mode or the

fine mode.

3. Turning on the output and press ing the output key.

The ke y LED turns on and disp lays CV or CC mode.

SAVE / RECALL SETUP

Save Setup

Back ground The front panel se ttings can be stored into one of

the four internal memories.

Contents The following list sh ows the se tup contents.。

●Fine / coarse kn ob editing mode

●Beep on / off

●Output voltage / current leve l

The following settings are always sa ve d as "off ".

● Output on / off

● Front panel lock on / off

Panel operation Press one of the 1 ~ 4 Memory ke ys for 2 se conds,

for example number 1. The panel se ttings are sa ve d

in memory No. 1 and the ke y LED turns on. When

the panel settings are modified, the LED turns off. 。

Panel operatio n

KORAD

KA3000/6000-Series User Manual

KORAD

KA3000/6000-Series User Manual

1 5

REMOTE CONTROL PROCEDURES

Entering the Remote Control Mode

1.Connecting USB

2.The power supply will automatically connect. After

normal connection, there will be a tweet from the

power supply itself.

3.The panel keys are locked, so the power supply can only

rely on the remote control.

Exiting from the Remote Control Mode

1.Closing the remote control software.

2. Disconnecting USB from the back.

3. The power supply disconnects; a tweet from the beep with

the hint that the remote control is over.

4. The power supply automatically comes into the panel

control mode.

1 6

Q1: The pane l but tons don' t wor k when pow er on.

Q2: Pressi ng ON/OFF, ther e is no out put when pow er on.

Q3: Output vol tage rises slowly when out put but ton is on.

A1: The pane l is locked. Pr es s the key for ov er 2 sec on ds, and then

the pa ne l will unlock.

A2: Cur ren t set up is 0.

A3: Cur ren t set up is too smal l.

Q4: Maki ng OCP on and pressi ng out put switch; and then the out put is

aut omatical ly shut off .

A4: Cur ren t protec tion val ue setup is too smal l. You could pres s ou tpu t

swi tch and then make OC P on.

LOCK

UNLOCK

FAQ

APS-7313 APS-7315 APS-7612

Aktakom APS-7315 User manual

This manual is also suitable for

Aktakom APS-7315 User manual

Related papers

Other documents