TA2055B

Scosche TA2055B User manual

  • Hello! I am an AI chatbot trained to assist you with the Scosche TA2055B User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
© 2006 SCOSCHE INDUSTRIES, INC.
SI 08/06 - TA2055B (3000003)
If you have any further questions, call our toll free technical help line at: 1-800-621-3695x3
TA2055B
IN-DASH INSTALLATION KIT FOR
2006-UP TOYOTA RAV4
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/
codes and information pertaining to installation of this kit (TA2055B) in 2006 Toyota RAV4 Vehicles. Scosche Industries, Inc. can
not be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing changes or
options, or damage that may occur in the automobile during the installation of components while using this booklet.
INTRODUCTION / PRELIMINARY
2
For Factory Wiring Codes go to: www.scosche-cars.com
FACTORY WIRING CODES
CAR STEREO CONNECTORS
PROVIDE EASY CONNECTION OF YOUR CAR
STEREO TO FACTORY WIRING HARNESS.
TA02
1987-UP Toyota
MOUNTING THE RADIO
DIN-ISO MOUNT
1. Snap the 6117L and 6117R brackets to the mounting locations on the 6113 kit panel. Secure
the 6116 pocket to the 6117L/R brackets with the supplied hardware in the installation kit.
2. Align the pocket to the lower edge of the opening in the panel. Then slide in, as shown. The
front of the pocket should rest to front of panel. (See Illustration 2).
3. Install (2) pocket screws as shown. (See Illustration 2).
4. Align, position and bolt the aftermarket DIN-ISO head unit to the 6117L/6117R brackets. Use
hardware supplied with aftermarket radio to secure the mounting brackets to the aftermarket
radio.
5. Snap the 6114 single DIN trim ring to complete mounting.
VEHICLE DISASSEMBLY
2006 TOYOTA RAV4
Radio Removal
1. Using a panel removal tool, remove both left and right panels located on each side off the radio.
2. Remove the (4) 10mm bolts securing the radio to the dash. Disconnect and remove.
This premium installation kit is for 2006-Up Toyota RAV4 vehicles. Included are all the parts you need
to mount your car stereo/cassette or CD player into your vehicle's dash. Refer to the individual
instruction in this manual to remove your vehicle's factory radio and assemble the kit.
CAUTION:
DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP
PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/OHN METER OVER A TEST LIGHT
TO CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S
COMPUTER AND/OR DIAGNOSTIC SYSTEMS. AVOID ALL FACTORY AIRBAG WIRING - AIRBAGS CAN
ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY OR DEATH.
NOTES:
See your vehicle's instructions for any special tools your installation might require.
Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting
instructions.
6117L
MOUNTING
BRACKET,
LEFT
VARIOUS REAR
SUPPORT BRACKETS
ASSEMBLED TA2055
WITH POCKET
DIN MOUNT
RADIO
6114 TRIM
DOUBLE-DIN ISO MOUNT
1. Snap the 6117L and 6117R brackets to the mounting locations on the 6113 kit panel.
2. Align, position and bolt the aftermarket DIN-ISO head unit to the 6117L/6117R brackets. Use
hardware supplied with aftermarket radio to secure the mounting brackets to the aftermarket
radio.
4. Snap the 6115 double DIN trim ring to
complete mounting.
6116 POCKET
6113 KIT
PANEL
6115
DOUBLE
DIN
TRIM
RING
6117R
MOUNTING
BRACKET,
RIGHT
6114
SINGLE
DIN
TRIM
RING
CAUTION:
REAR SUPPORT AVAILABLE
SEPARATELY. REAR
SUPPORTING THE RADIO
ADDS TO THE INSTALLATION’S
STRUCTURAL INTEGRITY.
6115 TRIM
DOUBLE DIN
MOUNT RADIO
ASSEMBLED TA2055
WITH DOUBLE DIN
ILLUSTRATION 2
ILLUSTRATION 3
/