ZiLOG Z8F011A User manual

Z8F011A
ZiLOG
Brand
ZiLOG
Model
Z8F011A
Type
User manual

This manual is also suitable for

Copyright ©2009 by Zilog
®
, Inc. All rights reserved.
www.zilog.com
Z8 Encore! XP
®
F082A Series
Development Kit
User Manual
UM018606-0109
Z8F08A28100KITG
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Revision History
ii
Revision History
Each instance in Revision History reflects a change to this document from
its previous revision. For more details, refer to the corresponding pages
and appropriate links in the table below.
Date
Revision
Level Description Page Number
January
2009
06 Updated Hardware section. 1
May
2008
05 Updated Introduction section. Changed
’Z8F08A28100KIT’ to ’Z8F08A28100KITG’.
1
March
2008
04 Updated the new Zilog logo, implemented Style
Guide, and changed ZiLOG to Zilog. Changed title
to Z8 Encore! XP F082A Series Development Kit.
Modified Schematics Table 2 to incorporate
changes to R15 from 220 Ω to 0 Ω. Added Note 3 to
the Schematics.
All
October
2005
03 F08xA Series development board, Corrected typo in
MCU features list: updated schematics for board rev
C.
6, 9
February
2005
02 Introduction, Corrected Typo in development kit
name.
1
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Table of Contents
iii
Table of Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Software (on CD-ROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Z8 Encore! XP F082A Series Development Board. . . . . . . . . . . . . . 5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
UART with IrDA Endec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Power and Communication Interfaces . . . . . . . . . . . . . . . . . . . . . . . 8
External Interface Headers JP1 and JP2 . . . . . . . . . . . . . . . . . . . . . 8
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Customer Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Introduction
1
Introduction
Zilog’s Z8 Encore! XP
®
F082A Series microcontroller unit (MCU) is a
part of the line of Zilog’s MCU products. The Z8 Encore! XP F082A
Series MCU development kit (Z8F08A28100KITG) enables you to
become familiar with the hardware and software tools available with this
product. This kit consists of the 8 KB version of the Z8 Encore! XP devel-
opment board that supports and presents the features of the Z8 Encore!
XP F082A Series. This kit allows you to begin writing application soft-
ware and contains all supporting documents.
This manual acquaints you with the Z8 Encore! XP F082A Series MCU
development kit, and provides instructions on setting up and using the
tools to start building designs and applications. Z8F082ASJ020 is the sili-
con used in the board. For more information, refer to Z8 Encore! XP
®
F082A Series Product Specification (PS0228).
Kit Contents
The Z8 Encore! XP F082A Series MCU development kit contains the
following:
Hardware
The hardware in Z8 Encore! XP F082A Series MCU development kit
include:
•
Z8 Encore! XP F082A Series development board
•
USB Smart Cable for PC to Z8 Encore! XP
®
F082A series develop-
ment board (previous versions of the development kit used a serial
smart cable; for information on using the serial smart cable, refer to
your original documentation)
•
5 V DC power supply
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Introduction
2
Figure 1. Z8 Encore! XP
®
F082A Series Development Kit Contents
Software (on CD-ROM)
The software in Z8 Encore! XP F082A Series MCU development kit
include:
•
ZDS II—Z8 Encore!
®
IDE with ANSI C-Compiler
•
Sample code
•
Document browser
•
Acrobat Reader
Development
Board
Packaging
CD-ROM Containing
Documentation
Serial Smart Cable
Power
Supply
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Introduction
3
Documentation
The following documents are included in the Z8 Encore! XP F082A
Series development kit:
•
Quick Start Guide
•
Z8 Encore! XP F082A Series technical documentation (on CD-ROM)
– Development Kit User Manual
– ZDS II—IDE User Manual
– eZ8 CPU User Manual
– Application Notes
The sample code is installed with ZDS II and is located in the
<instal-
lation directory>\samples
in the disk drive.
The documentation can be installed with the DemoShield interface or
viewed on the CD-ROM using the DemoShield menus and a PDF reader.
A copy of the Acrobat installer is provided on the CD-ROM and can be
installed from the DemoShield install screen. After installing the
documentation, Windows Explorer can be used to select any document to
be viewed with PDF file viewer.
System Requirements
An IBM PC (or compatible computer) with the following minimum
configurations are required:
•
Microsoft Windows XP Professional SP1/Windows 2000 SP3/Win-
dows NT 4.0 SP6/Windows 98 SE
•
Pentium II/233 MHz processor or higher up to Pentium IV, 2.8 GHz
•
96 MB RAM or more
•
25 MB hard disk space or more
•
Super VGA video adapter
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Introduction
4
•
CD-ROM
•
One or more RS-232 communication ports
Installation
For details on installation and setup of the Z8 Encore! XP F082A Series
development kit, refer to Z8 Encore! XP
®
/Z8 Encore!
®
Development Kits
Quick Start Guide (QS0043).
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Z8 Encore! XP F082A Series Development Board
5
Z8 Encore! XP F082A Series
Development Board
Introduction
Zilog’s Z8 Encore! XP
®
F082A Series development board is a
development and prototyping board for the Z8 Encore! XP F082A Series
MCU. The board provides you with a tool to evaluate features of Z8
Encore! XP F082A Series MCU, and to start developing an application
before building the hardware.
Figure 2. Z8 Encore! XP
®
F082A Series Development Board
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Z8 Encore! XP F082A Series Development Board
6
Features
The features of Z8 Encore! XP
®
F082A Series development board
include:
•
Z8 Encore! XP MCU (28-pin SOIC)
•
3 LEDs
•
RS-232 interface
•
IrDA transceiver
•
Two pushbuttons, RESET and TEST
•
5 V DC power connector
•
On-Chip Debugger interface
•
20 MHz Ceramic Oscillator (Y1)
•
Header for ADC input
•
Prototyping area
•
External interface connectors JP1 and JP2
•
2.7 V–3.6 V operating voltage with 5 V-tolerant inputs
MCU
The Z8 Encore! XP F082A Series MCU is a member of the family of
Zilog MCU products based on the 8-bit eZ8 core CPU. The Flash in-cir-
cuit programming capability allows for faster development time and pro-
gram changes in the field. The eZ8 core CPU is upward compatible with
existing Z8
®
instructions. The rich peripheral set of the Z8 Encore! XP
F082A Series makes it suitable for a variety of applications including
motor control, security systems, home appliances, personal electronic
devices, and sensors.
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Z8 Encore! XP F082A Series Development Board
7
The development board contains circuitry to support and present all the
features of the Z8 Encore! XP F082A Series. The key features of the Z8
Encore! XP F082A Series include:
•
eZ8 core CPU
•
8 KB Flash memory with in-circuit programming capability
•
1 KB register RAM
•
8-channel, 10-bit Analog-to-Digital Converter (ADC)
•
Full-duplex UART
•
Infrared Data Association (IrDA)-compliant infrared encoder/decoder
•
Two 16-bit timers with capture, compare, and PWM capability
•
Watchdog Timer (WDT) with internal RC oscillator
•
Eleven (20-pin package) or nineteen (28-pin package) I/O pins
•
Programmable priority interrupts
•
On-Chip Debugger
•
Voltage Brownout (VBO) Protection
•
Power-On Reset (POR)
•
2.7 V–3.6 V operating voltage with 5 V-tolerant inputs
•
Operating temperatures: 20 °C ±10 °C
For further information on the Z8 Encore!
®
family of devices, refer to Z8
Encore! XP
®
F082A Series Product Specification (PS0228), available for
download at w
ww.zilog.com.
UART with IrDA Endec
Z8 Encore! XP F082A Series (component U5) contains a fully-functional,
high-performance UART with Infrared Encoder/Decoder (ENDEC). The
Infrared Endec is integrated with an on-chip UART allowing easy
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Z8 Encore! XP F082A Series Development Board
8
communication between the Z8 Encore! XP F082A Series and IrDA
transceivers. Infrared communication provides secure, reliable, low-cost,
point-to-point communication between PCs, PDAs, cell phones, printers,
and other infrared enabled devices.
Power and Communication Interfaces
Table 1 lists jumper information concerning the shunt status, functions,
devices and defaults affected of jumpers JP3 and JP4.
External Interface Headers JP1 and JP2
External interface headers JP1 and JP2 are displayed in Schematics on
page 9.
Table 1. Jumpers JP3 and JP4
Jumper Status
Device
Affected Status Default
JP3* OUT RS-232
interface
Enabled X
JP3 IN RS-232
interface
Disabled
JP4* OUT IrDA
interface
Enabled
JP4 IN IrDA
interface
Disabled X
JP5 OUT U5 RESET
/
PD0
PD0 (GPIO) X
JP5 IN U5 RESET
/
PD0
RESET when
SW1 pressed
*These jumpers must not be OUT at the same time.
UM018606-0109 Schematics
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
9
Schematics
Figure 3 and Figure 4 on page 10 display the schematics for Z8 Encore! XP F082A Series development board.
Figure 3. Schematic, Z8 Encore! XP
®
F082A Series MCU Development Board
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
PB0_ANA0 PB2_ANA2
VCC_33V
PB3_ANA3
GND
PB1_ANA1
PB3_ANA3
PB0_ANA0
PB4_ANA7
PB2_ANA2
A20
-CS0
A12
-IOREQ
-F91_WE
A13
GND
GND
A17
A21
VCC_33V
A14
D1
VCC_33V
D7
-DIS_FLASH
GND
A6 A0
D3
D6
-BUSACK
A3
D2
VCC_33V
A15
A4
-TRSTN
D0
-MREQ
A7
A10
A9
A16A18
A11
-INSTRD
A19
A5
GNDD5
-CS1
A22
A1A2
-CS2
-RD
A8
GND
D4
A23
-WR
-BUSREQ
GND
PB7
PA3_CTS0
PC7
VCC_33V
PC4
PA7_T1OUT PA2
PA1_T0OUT_JPGND
GND
PC5
PA4_RXD0 PA5_TXD0
GND
GND
PB6
PA0_T0IN_JP
PC6
PA6_nT1OUT
PA7_T1OUT
GNDVCC_33V
GND
-DIS_IrDA
PB1_ANA1
PA2
VCC_33V
GND
PA5_TXD0
PB1_ANA1 PB0_ANA0
DBG
PA3_CTS0
PA4_RXD0
PB2_ANA2
PB3_ANA3
PA0_T0IN
PC3_COUT
PA7_T1OUT
PC3_COUT
PC2_ANA6
PC1_ANA5
PC0_ANA4
PD0
PA6_nT1OUT
PC2_ANA6 PB4_ANA7
PC0_ANA4
PC1_ANA5
PC2_ANA6
PB6
PB7GND
PC5
PB2_ANA2
PA2
PC0_ANA4
PC2_ANA6
PA5_TXD0
PD0
PC3_COUT
PC1_ANA5
PA4_RXD0 PC4
VCC_33V
PC7
PA2
PA6_nT1OUT
PA1_T0OUT
PC6
PA3_CTS0
GND
PC1_ANA5
PA7_T1OUT
PB0_ANA0
GND
PA1_T0OUT
PB1_ANA1
PA0_T0IN
PB4_ANA7
PC0_ANA4
PB3_ANA3
DBG
PB4_ANA7 PC2_ANA6
PC0_ANA4
PB2_ANA2
PB0_ANA0
PC1_ANA5
PB3_ANA3
PB1_ANA1
PB5_JPPC3_COUT
PD0
GND
VCC_33V
VCC_33V
PA6_nT1OUT
-RESET
VCC_33V
PA0_T0IN_JP
PA1_T0OUT_JP
PB5
PB5_JP
GND
VCC_33V
DBG
-DIS_IRDA
-DIS_232
PA3_CTS0
PA4_RXD0
PA5_TXD0
SENSE
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
23Tuesday, March 18, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
23Tuesday, March 18, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
23Tuesday, March 18, 2008
connector 2
connector 1
for
reference
only
If Module is plugged onto the Dev Platform the local
RS232 interface is disabled by pin 50 of JP2
TEST
20 pin footprint
28 pin footprint
RESET/TEST2
Note 1:
PB6 and PB7 are dual function pins (GPIO or Analog supply)
R12, R13, R16, and R17 are zero-ohm resistors used in
conjunction with GPIO Control Registers to select function
desired. C21, C22, and C23 are bypass capacitors that are used
for better noise rejection. U8 is an optional filter that can
be used to improve the quality of the Analog Supply. The
development board is shipped configured for Analog Supply.
Table 1 shows the configurations recommended
NOTE 1:
NOTE 1:
NOTE 2
Note 2: The XP supports internal, external crystal, external
ceramic resonator, external R/C and external CMOS drive
clock modes. R14, R15, R18, C19, C20 and Y1 are used to
support the clock mode selected. The development board is
shipped configured for external 20MHz ceramic resonator or
internal clock operation. When using Internal oscilator,
pins 7 and 8 could be used as GPIO ports PA0 and PA1. To do
so install R20 and R21.
Table 2 shows the recommended clock mode configurations.
Clock Mode R14 R15 R18 C19 C20 Y1
Internal Only none none none none none none
Crystal 0 Ohm 0 Ohm none Yes Yes Yes
Ceramic Res 0 Ohm 0 Ohm none none none Yes
External CMOS none none none none none none
TABLE 2
(Use PA0_T0IN
pin on JP2)
Supply
R12 R13 R16 R17 R22 U8 C21...C23
Analog IN OUT IN OUT OUT optional IN
GPIO OUT IN OUT IN IN OUT OUT
TABLE 1
NOTE 3:
Resistors R20 and R21 are not populated. See Note 2.
C22
0.033uF
C22
0.033uF
R16
0
R16
0
R21
0
R21
0
R10
10
R10
10
R18
1M
R18
1M
C13
0.001uF
C13
0.001uF
R15
0
R15
0
R9
100K
R9
100K
R19
10K
R19
10K
D2
GREEN
D2
GREEN
21
SW1SW1
R22
0
R22
0
+
C23
30uF
+
C23
30uF
D3
YELL
D3
YELL
21
D4
RED
D4
RED
21
C17
0.001uF
C17
0.001uF
C21
0.033uF
C21
0.033uF
C11
0.001uF
C11
0.001uF
JP2
HEADER 30x2/SM
JP2
HEADER 30x2/SM
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
C16
0.001uF
C16
0.001uF
R17
0
R17
0
U5
Z8F04xA_28
U5
Z8F04xA_28
GND
9
PC4/LED
16
PA6/T1IN/T1OUT
15
PA5/TXD0
14
PA4/RXD0
13
PA3/CTS0
12
PB3/ANA3/CLKIN
4
PA0/T0IN/T0OUTXIN
7
VDD
6
PB1/ANA1
28
PB0/ANA0
27
PC1/ANA5/CINN/LED
24
PC2/ANA6/LED
25
PC3/COUT/LED
26
PC0/ANA4/CINP/LED
23
PB2/ANA2
1
PC6/LED
19
PC7/LED
20
PA2/DE
11
PB5/Vref
3
PB4/ANA7
2
PA7/T1OUT
18
PC5/LED
17
PB7(AGND)
10
PA1/T0OUT/XOUT
8
PB6(AVDD)
5
RESET/PD0
21
DBG
22
C14
0.001uF
C14
0.001uF
Y1
20 MHz
Y1
20 MHz
1
1
2
2
3
3
R12
0
R12
0
R7
100
R7
100
C15
0.001uF
C15
0.001uF
C19C19
R13
0
R13
0
J2
HEADER 8X2
J2
HEADER 8X2
2
4
6
8
10
12
14
16
1
3
5
7
9
11
13
15
R20
0
R20
0
R8
100
R8
100
U6
Z8F04xA
U6
Z8F04xA
PB2/ANA2
2
PA4/RXD0
10
PA3/CTS0
9
PA2/DE
8
PB3/CLKIN/ANA3
3
PA1/T0OUT/XOUT
6
PA0/T0IN/T0OUT/XIN/
5
PB0/ANA0
20
PB1/ANA1
1
PC1ANA5/CINN/LED
17
PC0/ANA4/CINP/LED
16
DBG
15
PA7/T1OUT
13
PA6/T1IN/T1OUT
12
PA5/TXD0
11
RESET/PD0
14
GND
7
VDD
4
PC3/COUT/LED
19
PC2/ANA6/LED
18
C12
0.001uF
C12
0.001uF
R14
0
R14
0
SW2SW2
C20C20
C10
0.001uF
C10
0.001uF
R11
100
R11
100
U8
EMI Filter
U8
EMI Filter
IO
1
GND
2
IO
3
JP5
HEADER 2
JP5
HEADER 2
1
2
JP1
HEADER 30x2/SM
JP1
HEADER 30x2/SM
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
C18
0.001uF
C18
0.001uF
UM018606-0109 Schematics
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
10
Figure 4. Schematic, Z8 Encore! XP
®
F082A Series MCU Development Board
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
TXD0
GND
CTS0
RXD0
VCC_33V
DBG
PA4_RXD0
PA5_TXD0
IRDA_SD
GND
PA3_CTS0
VCC_33V
GND
VCC_33V
PA5_TXD0
VCC_33V
PA4_RXD0
GND
VCC_33V
GND
-Z_RST
GND
GND
5V
VCC_33V
VCC
GND
-Z_RST
PA3_CTS0
DBG
-DIS_IRDA
-DIS_232
PA5_TXD0
PA4_RXD0
VCC_33V
GND
SENSE
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
33Wednesday, March 12, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
33Wednesday, March 12, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
33Wednesday, March 12, 2008
CONSOLE
GND
USER
DBG
INTERFACE
DIS RS232
DIS IRDA
3.3 OK
C2
0.1uF
C2
0.1uF
R3
68
R3
68
C4
0.1uF
C4
0.1uF
U3E
74LVC04/SO
U3E
74LVC04/SO
11 10
147
U3A
74LVC04/SO
U3A
74LVC04/SO
1 2
147
U7
LT1129-3.3/DD
U7
LT1129-3.3/DD
OUT
1
SENSE
2
GND
3
SHDN
4
VIN
5
C6
0.1uF
C6
0.1uF
JP3JP3
1
2
U3D
74LVC04/SO
U3D
74LVC04/SO
9 8
147
P2
Header 3x2
P2
Header 3x2
1 2
3 4
5 6
R2
10K
R2
10K
U3B
74LVC04/SO
U3B
74LVC04/SO
3 4
147
R23
10K
R23
10K
U3F
74LVC04/SO
U3F
74LVC04/SO
13 12
147
C1
0.1uF
C1
0.1uF
JP4JP4
1
2
C9
330nF
C9
330nF
R1
680
R1
680
F1
RXE050
F1
RXE050
R24
15K
R24
15K
R4
2R7
R4
2R7
C5
0.1uF
C5
0.1uF
J1
PWR JACK
J1
PWR JACK
2
3
1
U4
ZHX1810
U4
ZHX1810
TXD
2
SD
4
RXD
3
LEDA
1
VCC
5
GND
6
T
0
+
C7
100/10
+
C7
100/10
C8
0.1uF
C8
0.1uF
R5
10K
R5
10K
+
C3
100/10
+
C3
100/10
U3C
74LVC04/SO
U3C
74LVC04/SO
5 6
147
P1
DB9 Female
P1
DB9 Female
5
9
4
8
3
7
2
6
1
U1
MAX3222
U1
MAX3222
EN
1
C1+
2
C1-
4
C2+
5
C2-
6
T1IN
13
T2IN
12
R1OUT
15
R2OUT
10
V+
3
V-
7
T1OUT
17
T2OUT
8
R1IN
16
R2IN
9
SHDN
20
VCC
19
GND
18
NC
11
NC
14
TP1TP1
1
2
3
4
5
R6
10K
R6
10K
D1
LED
D1
LED
21
TP2TP2
1
2
3
4
5
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109 Customer Support
11
Customer Support
For answers to technical questions about the product, documentation, or
any other issues with Zilog’s offerings, please visit Zilog’s Knowledge
Base at http://www.zilog.com/kb
.
For any comments, detail technical questions, or reporting problems,
please visit Zilog’s Technical Support at http://support.zilog.com
.
Z8 Encore! XP
®
F082A Series Development Kit
User Manual
UM018606-0109
12
DO NOT USE IN LIFE SUPPORT
LIFE SUPPORT POLICY
ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE
EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant
into the body, or (b) support or sustain life and whose failure to perform when properly
used in accordance with instructions for use provided in the labeling can be reasonably
expected to result in a significant injury to the user. A critical component is any
component in a life support device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.
Document Disclaimer
©2009 by Zilog, Inc. All rights reserved. Information in this publication concerning the
devices, applications, or technology described is intended to suggest possible uses and
may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR
PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE.The
information contained within this document has been verified according to the general
principles of electrical and mechanical engineering.
Z8, Z8 Encore!, and Z8 Encore! XP are registered trademarks of Zilog, Inc. All other
product or service names are the property of their respective owners.
Warning:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

ZiLOG Z8F011A User manual

Z8F011A
ZiLOG
Brand
ZiLOG
Model
Z8F011A
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents