Anova RCPWT63 Installation guide

Anova
Brand
Anova
Model
RCPWT63
Type
Installation guide

This manual is also suitable for

anovafurnishings.com
888.535.5005 tel
Installation Instructions
TOOLS NEEDED: HARDWARE NEEDED:
Step-by-Step Installation Sequence
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
4,000 psi minimum and be cured for at least 28 days prior to the installation of the table and benches.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
Hammer DrillHammer
Pencil
Wire Brush
Level
Safety Glasses
Wainwright Picnic Table and Benches Set
9/16"Wrench
Masonry Drill Bit Set
3/16" and 3/8"
Optional: (12) 3/8"
Rubber Washers
90130A050
(12) 3/8" x 3.5" 18-8
Stainless Steel Stud Anchors
92188A202
Installation Instructions
Step-by-Step Installation Sequence
2
1.
2.
3.
4.
5. Use the hammer to x the anchor into the drilled hole by giving it several
hammer blows.
6. Repeat steps 2 - 5 until all anchors are installed.
5
4
Place table and benches in the desired location. Mark the location of the
holes with a pencil. To verify the alignment of the anchor markings you may
reference the bottom of page 3.
! It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with a 3/16" diameter drill bit followed by a 3/8" diameter bit.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
Locate an anchor and adjust the nut so it is ush with the top of the anchor to
protect the threads from being damaged. Insert the anchor into the hole.
Care should be given to avoid rubbing the powder coating o the foot. A rubber
washer is a suitable replacement option. Mount the table to the ground by placing a
washer and a nut onto each anchor. Leave the hardware nger tight until all of them have
been installed. Verify that the table is level before tightening the anchors. Tighten all of
the hardware with a 9/16" wrench.
Repeat steps 7 and 8 to install the benches.
7. Remove the nuts and washers o of the anchors. Align the mounting holes of the table
over top of the anchors and slide it down into place.
8.
9.
!
7
Wainwright Picnic Table and Benches Set
8a
8b
Copyright 2019 ANOVA® Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
FOOT MOUNTS:
SECTION A-A
SCALE 1 / 25
A A
1
1
2
2
A A
B B
1
001
OF
RCPWT63A
1
REV
SHEET1 / 25
SCALE
DATE 4/17/2018
DWG NO
TITLE
A
DRAWN D. METZ
SIZE
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125 .0625 DURING COATING.
TOLERANCES UNLESS NOTED:
X1 X.X .5 X.XX ±.25 X.XXX ±.125
X.XXXX ±.0625 X.XXXXX ±.03125
X.XXXXXX .015625 ANGULAR ±1°
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
NOTES:
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
REV DESCRIPTION ECN TR.# DATE
001 01/21/18
14.562X
(2 PLCS) 28.002X
68.004X
.50
(12 PLCS)
25.002X
(4 PLCS)
SECTION A-A
SCALE 1 / 25
A A
1
1
2
2
A A
B B
1
001
OF
RCPWT63
1
REV
SHEET1 / 25
SCALE
DATE 4/17/2018
DWG NO
TITLE
A
DRAWN D. METZ
SIZE
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125 .0625 DURING COATING.
TOLERANCES UNLESS NOTED:
X
1 X.X
.5 X.XX ±.25 X.XXX ±.125
X.XXXX ±.0625 X.XXXXX ±.03125
X.XXXXXX
.015625 ANGULAR ±1°
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
NOTES:
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
REV DESCRIPTION ECN TR.# DATE
001 01/21/18
.50
(12 PLCS)
14.562X
(2 PLCS)
25.002X
68.006X
(4 PLCS)
02/12/2019
Wainwright Picnic Table and Benches Set
8.00"
(4 PLCS)
8.00"
(4 PLCS)
2X 25.00"
2X 25.00"
2X 28.00"
2X 14.56"
(2 PLCS)
2X 14.56"
(2 PLCS)
6X 68.00"
6X 68.00"
Ø.50"
(12 PLCS)
Ø.50"
(12 PLCS)
RCPWT63
RCPWT63A
  • Page 1 1
  • Page 2 2
  • Page 3 3

Anova RCPWT63 Installation guide

Anova
Brand
Anova
Model
RCPWT63
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents