ML Accessories SF8350MW User manual

Brand: ML Accessories

Model: SF8350MW

Type: User manual

This manual is also suitable for

SF8360MW

These instructions should be read carefully and

retained after installation by the end user for

future reference and maintenance.

SAFETY

• This product must be installed in accordance

with the latest edition of the IEE Wiring

Regulations (BS7671) and current Building

Regulations. If in any doubt, consult a

qualiﬁed electrician

• Please isolate mains prior to installation

or maintenance

• Check the total load on the circuit (including

when this product is ﬁtted) does not exceed

the rating of the circuit cable, fuse or

circuit breaker

• Do not overload this accessory or subject it to

conditions outside its rating

• Please note the IP (Ingress Protection) rating

of this product when deciding the location

for installation

INSTALLATION

• Connect the accessory as per the diagram in this

manual, ensuring the correct polarity is observed:

L – LIVE – Brown

N – NEUTRAL – Blue

EARTH – Green and yellow

• All earth connections must be made and

maintained. Use green/yellow sleeving on earth

conductors that are not insulated

• Check all electrical connections are secure with no

loose strands of cable

• Fit the unit into a suitable wall box taking care

not to compress, damage or trap any cables, and

secure with the screws provided. If using metal

mounting boxes with four lugs, remove the top and

bottom lugs or bend fully back

FLAT PLATE, SCREWLESS AND RAISED EDGE FIXING

• Always ensure the wall surface is ﬂat and smooth

• This unit is ﬁtted with a gasket - this MUST NOT

be removed, this gasket is to stop discolouration

of the plate due to natural moisture in some wall

ﬁnishes

• This product must be ﬁtted only after painting and

decorating is complete

13A SWITCHED SOCKET 13A SOCKET WITH DUAL USB CHARGER 13A SOCKET WITH QUAD USB CHARGER / QUAD USB CHARGER 13A SOCKET WITH USB AND BLUETOOTH SPEAKER / STAND ALONE BLUETOOTH SPEAKER DUAL VOLTAGE SHAVER SOCKET 5A UNSWITCHED ROUND PIN SOCKET

• Screwless products only - remove the front plate

by placing a medium size ﬂat-head screwdriver in

the notch at the side and lever off gently. After wiring

and ﬁtting to the wall box as per the instructions in this

document, clip the front plate onto the main assembly

ensuring the screwdriver notch is at the side

METAL CLAD FIXING

• Remove front faceplate and mount rear box in a

suitable location. The back box has multiple 20mm

cable entry points to aid installation

• Wire as per the instructions in this document, and ﬁx

plate to back box using the screws provided

OUTLETS WITH USB CHARGING FUNCTION

These products are designed for charging portable USB

devices only, and contain a short circuit and overload

protection feature. If there is no power from the USB

socket unplug the connected device. Check to ensure the

USB socket and USB device have not come into contact

with water, liquid or debris and the cable to the device

is not damaged. With no device connected to the USB

socket it will automatically reset and be ready for use

WARNING

USB or Bluetooth products, dimmers, shaver sockets and

products with LED or neon indicators must be disconnected

from the circuit if subjected to any high voltage or insulation

resistance testing. Irreparable damage will occur if this

instruction is not followed. Please note this kind of damage

will void the warranty

GENERAL

This product should be recycled in the correct manner when

it reaches the end of its life. Check local authorities for

where facilities exist.

Clean with a soft dry cloth only, do not use aggressive

cleaning products or solvents which may damage the

product and invalidate the warranty

WARRANTY

Products have a warranty of 15 years from date of purchase with the exception of dimmers, USB chargers and

speaker products, which have a 3 year warranty. Failure to install this product in accordance with the current edition

of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch codes will invalidate the warranty. If this

product should fail within its warranty period it should be returned to the place of purchase for a free of charge

replacement. ML Accessories does not accept responsibility for any installation costs associated with the

replacement product. Your sta tutory rights are not affected. ML Ac cessories reserve the right to alter product

specification without prior notice.

13A SWITCHED SOCKET

13A SOCKET WITH DUAL USB CHARGERS

CHARGING INDICATOR

The charger status indicator will change colour depending on the level of current drawn by the connected device.

The Red/Green status indicator is not exact, please refer to device battery level for true reading.

13A SOCKET WITH USB AND BLUETOOTH SPEAKER / STAND ALONE BLUETOOTH SPEAKER

WARRANTY

Products have a warranty of 15 years from date of purchase with the exception of dimmers, USB chargers and

speaker products, which have a 3 year warranty. Failure to install this product in accordance with the current edition

of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch codes will invalidate the warranty. If this

product should fail within its warranty period it should be returned to the place of purchase for a free of charge

replacement. ML Accessories does not accept responsibility for any installation costs associated with the

replacement product. Your statutory rights are not affected. ML Ac cessories reserve the right to alter product

specification without prior notice.

13A SWITCHED SOCKET

13A SOCKET WITH DUAL USB CHARGERS

CHARGING INDICATOR

The charger status indicator will change colour depending on the level of current drawn by the connected device.

The Red/Green status indicator is not exact, please refer to device battery level for true reading.

13A SOCKET WITH USB AND BLUETOOTH SPEAKER / STAND ALONE BLUETOOTH SPEAKER

WARRANTY

Products have a warranty of 15 years from date of purchase with the exception of dimmers, USB chargers and

speaker products, which have a 3 year warranty. Failure to install this product in accordance with the current edition

of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch codes will invalidate the warranty. If this

product should fail within its warranty period it should be returned to the place of purchase for a free of charge

replacement. ML Accessories does not accept responsibility for any installation costs associated with the

replacement product. Your statutory rights are not affected. ML Ac cessories reserve the right to alter product

specification without prior notice.

13A SWITCHED SOCKET

13A SOCKET WITH DUAL USB CHARGERS

CHARGING INDICATOR

The charger status indicator will change colour depending on the level of current drawn by the connected device.

The Red/Green status indicator is not exact, please refer to device battery level for true reading.

13A SOCKET WITH USB AND BLUETOOTH SPEAKER / STAND ALONE BLUETOOTH SPEAKER

WARRANTY

Products have a warranty of 15 years from date of purchase with the exception of dimmers, USB chargers and

speaker products, which have a 3 year warranty. Failure to install this product in accordance with the current edition

of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch codes will invalidate the warranty. If this

product should fail within its warranty period it should be returned to the place of purchase for a free of charge

replacement. ML Accessories does not accept responsibility for any installation costs associated with the

replacement product. Your statutory rights are not affected. ML Ac cessories reserve the right to alter product

specification without prior notice.

13A SWITCHED SOCKET

13A SOCKET WITH DUAL USB CHARGERS

CHARGING INDICATOR

The charger status indicator will change colour depending on the level of current drawn by the connected device.

The Red/Green status indicator is not exact, please refer to device battery level for true reading.

13A SOCKET WITH USB AND BLUETOOTH SPEAKER / STAND ALONE BLUETOOTH SPEAKER

BLUETOOTH AUDIO SPECIFICATION

• Output Pow er: Max. 3W RMS

• Sensitivity: L/R 380MV

• SNR: >80dB

• Speaker Frequency Range: 280Hz – 16KHz

BLUETOOTH CONNECTION

• Press the power button directly under the speaker – Bluetoo th indicator will begin to flash

• Activate Bluetooth pairing on your mobile device and scan for Bluetooth devices

• Connect to the device named SPEAKER, SPEAKER01, SPEAKER02 etc.

• Once a connection has been established you will hear a “beep” sound and the Bluetooth indicator will flash at a

different frequency to confirm

13A SOCKET WITH QUAD USB AND QUAD OUTLET

DUAL VOLTAGE SHAVER SOCKET

BLUETOOTH AUDIO SPECIFICATION

• Output Pow er: Max. 3W RMS

• Sensitivity: L/R 380MV

• SNR: >80dB

• Speaker Frequency Range: 280Hz – 16KHz

BLUETOOTH CONNECTION

• Press the power button directly under the speaker – Bluetoo th indicator will begin to flash

• Activate Bluetooth pairing on your mobile device and scan for Bluetooth devices

• Connect to the device named SPEAKER, SPEAKER01, SPEAKER02 etc.

• Once a connection has been established you will hear a “beep” sound and the Bluetooth indicator will flash at a

different frequency to confirm

13A SOCKET WITH QUAD USB AND QUAD OUTLET

DUAL VOLTAGE SHAVER SOCKET

BLUETOOTH AUDIO SPECIFICATION

• Output Pow er: Max. 3W RMS

• Sensitivity: L/R 380MV

• SNR: >80dB

• Speaker Frequency Range: 280Hz – 16KHz

BLUETOOTH CONNECTION

• Press the power button directly under the speaker – Bluetooth indicator will begin to flash

• Activate Bluetooth pairing on your mobile device and scan for Bluetooth devices

• Connect to the device named SPEAKER, SPEAKER01, SPEAKER02 etc.

• Once a connection has been established you will hear a “beep” sound and the Bluetooth indicator will flash at a

different frequency to confirm

13A SOCKET WITH QUAD USB AND QUAD OUTLET

DUAL VOLTAGE SHAVER SOCKET

BLUETOOTH AUDIO SPECIFICATION

• Output Pow er: Max. 3W RMS

• Sensitivity: L/R 380MV

• SNR: >80dB

• Speaker Frequency Range: 280Hz – 16KHz

BLUETOOTH CONNECTION

• Press the power button directly under the speaker – Bluetooth indicator will begin to flash

• Activate Bluetooth pairing on your mobile device and scan for Bluetooth devices

• Connect to the device named SPEAKER, SPEAKER01, SPEAKER02 etc.

• Once a connection has been established you will hear a “beep” sound and the Bluetooth indicator will flash at a

different frequency to confirm

13A SOCKET WITH QUAD USB AND QUAD OUTLET

DUAL VOLTAGE SHAVER SOCKET

5A UNSWITCHED ROUND SOCKET

10AX 2-WAY SWITCH

Terminal positions may alter

5A UNSWITCHED ROUND SOCKET

10AX 2-WAY SWITCH

Terminal positions may alter

BLUETOOTH AUDIO

SPECIFICATION

• Output Power: Max. 3W RMS

• Sensitivity: L/R 380MV

• SNR: >80dB

• Speaker Frequency Range:

280Hz – 16KHz

BLUETOOTH CONNECTION

• Press the power button directly under the speaker

– Bluetooth indicator will begin to ﬂash

• Activate Bluetooth pairing on your mobile device and scan for

Bluetooth devices

• Connect to the device named

SPEAKER, SPEAKER01, SPEAKER02 etc.

• Once a connection has been established you will hear a “beep”

sound and the Bluetooth indicator will ﬂash at a different

frequency to conﬁrm

WARNING

This unit should NOT be subject to any insulation resistance

testing, failure to follow this instruction could cause damage

to the USB circuit and void the warranty.

THIS LABEL SHOULD BE REMOVED DURING INSTALLATION

! !

CHARGING INDICATOR

If you have purchased a model with an LED charger status indicator, it will change colour

depending on the level of current drawn by the connected device. The Red/Green status

indicator gives an approximate charge reading - please refer to device battery level for

true reading.

WARRANTY Knightsbridge Wiring Accessories have a have a mechanical warranty of 15 years from date of purchase with the exception of dimmers, USB chargers and speaker products, which have a 2 year warranty. Failure

to install this product in accordance with the current edition of the IEE Wiring Regulations (BS 7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period

it should be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not

affected. ML Accessories reserve the right to alter product speciﬁcation without prior notice.

ML Accessories Limited Unit E, Chiltern Park, Boscombe Road, Dunstable, LU5 4LT www.mlaccessories.co.uk

13A FUSED SPUR / SWITCHED FUSED SPUR 20A SWITCHES 45A DP SWITCHES 45A DP SWITCHES WITH

13A SWITCHED SOCKETS

45A DP SWITCHES WITH 13A SWITCHED SOCKETS

AND DUAL USB CHARGERS

DIMMERS

Please check with LED lamp manufacturer for

compatibility

Ensure a mixed load is not selected, i.e.

incandescent mixed with LED

Consider the minimum and maximum range

of the dimmer according to the type of load

installed

ADJUSTING THE MINIMUM DIMMING LEVEL

(on products with potentiometer)

• Isolate the power and rotate the dimmer

to its minimum position

• With the aid of a small slotted screwdriver,

rotate the potentiometer (clockwise to

increase, anti-clockwise to decrease the

minimum dimming level)

• Switch on and check for correct operation

• To improve dimming curve repeat the

previous steps

• A small audible buzz may be emitted when

dimming certain products, this is normal

10AX INTERMEDIATE SWITCH

Terminal positions may alter

10A FAN ISOLATOR

DIMMERS

Please check with LED lamp manufacturer for compatibility

Ensure a mixed load is not selected, i.e. incandescent mixed with LED

Consider the minimum and maximum range of the dimmer according to the type of load installed

ADJUSTING THE MINIMUM DIMMING LEVEL (on products with potentiometer)

• Isolate the power and rotate the dimmer to its minimum position

• With the aid of a small slotted screwdriver, rotate the potentiometer (clockwise to increase, anti-clockwise to

decrease the minimum dimming level)

• Switch on and check for correct operation

• To improve dimming curve repeat the previous steps

• A small audible buzz may be emitted when dimming certain products, this is normal

13A FUSED SPUR / SWITCHED FUSED SPUR

20A SWITCHES

ADJUSTING THE MINIMUM DIMMING LEVEL (on products with potentiometer)

• Isolate the power and rotate the dimmer to its minimum position

• With the aid of a small slotted screwdriver, rotate the potentiometer (clockwise to increase, anti-clockwise to

decrease the minimum dimming level)

• Switch on and check for correct operation

• To improve dimming curve repeat the previous steps

• A small audible buzz may be emitted when dimming certain products, this is normal

13A FUSED SPUR / SWITCHED FUSED SPUR

20A SWITCHES

ADJUSTING THE MINIMUM DIMMING LEVEL (on products with potentiometer)

• Isolate the power and rotate the dimmer to its minimum position

• With the aid of a small slotted screwdriver, rotate the potentiometer (clockwise to increase, anti-clockwise to

decrease the minimum dimming level)

• Switch on and check for correct operation

• To improve dimming curve repeat the previous steps

• A small audible buzz may be emitted when dimming certain products, this is normal

13A FUSED SPUR / SWITCHED FUSED SPUR

20A SWITCHES

ADJUSTING THE MINIMUM DIMMING LEVEL (on products with potentiometer)

• Isolate the power and rotate the dimmer to its minimum position

• With the aid of a small slotted screwdriver, rotate the potentiometer (clockwise to increase, anti-clockwise to

decrease the minimum dimming level)

• Switch on and check for correct operation

• To improve dimming curve repeat the previous steps

• A small audible buzz may be emitted when dimming certain products, this is normal

13A FUSED SPUR / SWITCHED FUSED SPUR

20A SWITCHES

45A SWITCHES / COOKER CONTROL UNITS

These products have no cable entry and should only be used for “hard wired” installations.

DCJAN19_V2

45A SWITCHES / COOKER CONTROL UNITS

These products have no cable entry and should only be used for “hard wired” installations.

DCJAN19_V2

45A SWITCHES / COOKER CONTROL UNITS

These products have no cable entry and should only be used for “hard wired” installations.

DCJAN19_V2

45A SWITCHES / COOKER CONTROL UNITS

These products have no cable entry and should only be used for “hard wired” installations.

DCJAN19_V2

Terminal positions may alter Terminal positions may alter

10AX 2-WAY SWITCH 10AX INTERMEDIATE SWITCH 10AX FAN ISOLATOR DIMMERS

DCJAN19_V2

These products have no cable entry and should only be used for “hard wired” installations.

These instructions should be read carefully and retained after installation for

further reference and maintenance

SAFETY

• This product must be installed in accordance with the latest edition of the

IEE Wiring Regulations (BS 7671) and current Building Regulations. If in any

doubt, consult a qualified electrician.

• Before installation or maintenance, ensure that the mains supply is switched

off and circuit fuses are removed or circuit breakers switched off

• Do not overload this accessory or subject it to conditions outside its rating

• Please recycle

PLATE FIXING

• Always ensure the wall surface is flat and smooth for optimum installation

• To maintain the finish of this product, periodically wipe over with a soft dry

cloth only, do not use abrasive cleaning products

DIMMERS

• Please check with LED lamp manufacturer for compatibility

• Our dimmers are rated 40-400W for incandescent loads and 3-100W for LED

WARRANTY

This product has a warranty of 15 years (3 years for dimmers and USB outlets)

from the date of purchase. Failure to install this product in accordance with

the current edition of the IEE Wiring Regulations (BS 7671), improper use

or removal of batch codes will invalidate the warranty. If this

product should fail within its warranty period it should be returned

to the place of purchase for a free of charge replacement. ML

Accessories Ltd does not accept responsibility for any installation

costs associated with the replacement product. Your statutory tights

are not affected. ML Accessories reserve the right to alter product

specification without prior notice.

INSTALLATION

1. Connect the accessory as per the relevant installation diagram

2. All earth connections must be made and maintained. Use green/

yellow sleeving on earth conductors that are not insulated.

3. Fit the unit into a suitable wall box taking care not to compress,

damage or trap any cables, and secure with the screws provided

4. Check all electrical connections are secure with no loose strands

of cable

WIRING

L – LIVE – Brown

N – Neutral – Blue - Earth – Green and yellow

* Note – USB products should not be connected during an insulation

resistance test or damage will occur

IF IN ANY DOUBT PLEASE CONSULT A QUALIFIED ELECTRICAN

112

WIRING ACCESSORIES

LIVE LIGHT

LIVE

1-WAY SWITCH

LIVE LIGHT

LIVE

2-WAY SWITCH

L1 L2

LIVE LIGHT

LIVE

INTERMEDIATE SWITCH

TERMINAL BLOCK

LIVE NEUTRAL

EARTH

FROM SUPPLY

20A SWITCH

LIVE NEUTRAL

EARTH

TO LOAD

FROM SUPPLY TO LIGHT

FROM SUPPLY TO LIGH

TFROM SUPPLY TO LIGHT

LIVENEUTRAL

EARTH

FROM SUPPLY

13A 2G SWITCHED SOCKET

LIVE NEUTRAL

EARTH

FROM SUPPLY

LIVENEUTRAL

EARTH

FROM SUPPLY

LIVE NEUTRAL

EARTH

TO LOAD

FUSE CONNECTION

UNIT

13A 1G

SWITCHED SOCKET

TO FUNCTIONAL EARTH

LIVE NEUTRAL

EARTH

45A SWITCH

LIVE NEUTRAL

EARTH

FROM SUPPLY

TO COOKER

COOKER CONTROL UNIT

LIVENEUTRAL

EARTH

LIVE NEUTRAL

EARTH

FROM SUPPLY

TO COOKER

LIVE

LIGHT

LIVE

FROM SUPPLYTO LIGHT

L1 L2 COM

TV SOCKET

SCREEN UNDER

CABLE CLAMP

TELEPHONE SOCKET

Colour Code

Pin Colour

1 Green or Green/White

2 Blue or Blue/White

3 Orange or Orange/White

4 White or White/Orange

5 White or White/Blue

6 White or White/Green

SHAVER SOCKET

LIVE NEUTRAL

EARTH

FROM SUPPLY

Normally a maximum of 5 telephones

can be connected to one exchange line.

Sockets are connected in parallel,

i.e Pin 1 to Pin 1;Pin 2 to Pin 2: etc.

LIVE NEUTRAL

EARTH

FROM SUPPLY

LIVE

NEUTRAL

EARTH

TO FUNCTIONAL EARTH

FROM SUPPLY

13A 1G SOCKET

WITH USB OUTLET

13A 2G SOCKET

WITH USB OUTLET

LIVE NEUTRAL

EARTH

FROM SUPPLY

13A 1G SOCKET

LIVE NEUTRAL

EARTH

FROM SUPPLY

5A 1G SOCKET

LIVE LIGHT

LIVE

FROM SUPPLY TO LIGHT

L1 L2 COM

2-WAY DIMMER

For multiple gang Dimmer (2, 3 & 4)

repeat wiring method for each Dimmer.

LIVENEUTRAL

EARTH

LIVE NEUTRAL

EARTH

FROM SUPPLY

TO LOAD

20A FLEX OUTLET

LIVENEUTRAL

EARTH

FROM SUPPLY

EARTH

TO COOKER

LIVENEUTRAL

45A COOKER OUTLET

SWITCHED FUSE

CONNECTION UNIT

EARTH

TO LOAD

LIVE

FROM SUPPLY

EARTH

LIVENEUTRAL

NEUTRAL

LIVENEUTRAL

EARTH

FROM SUPPLY

SWITCHED

LIVE

NEUTRAL

EARTH

TO FAN

COM

Brown sleeve

to be added to

switched live

3-POLE FAN SWITCH

/13A 2G SOCKET

NL LOOP

MAIN LOOP

TO SWTICH

TO PENDANT

Looping Circuit

LIVE

NEUTRAL

EARTH

NL LOOP

TO SWTICH

MAIN LOOP

MAIN LOOP TO PENDANT

Junction Box Circuit

SWITCHED

LIVE

SWITCHED LIVE (BLUE) MUST HAVE BROWN SLEEVE

LIVE

NEUTRAL

EARTH

NL LOOP

LIVE NEUTRAL

Cable Restraints Cable Restraints

BATTEN HOLDERS, CEILING ROSE & PENDANT SETS

LIVE

LIGHT

LIVE

FROM SUPPLYTO LIGHT

10A 1-WAY CEILING SWITCH

LIVE LIGHT

LIVE

FROM SUPPLYTO LIGHT

10A 2-WAY CEILING SWITCH

COM

L1 L2

COM

L1 L2

2-WAY SWITCH 2-WAY SWITCH

LIVE NEUTRAL

EARTH

FROM SUPPLY

LIVE NEUTRAL

EARTH

TO LOAD

45A CEILING SWITCH

TO SWTICH

MAIN LOOP

SWITCHED

LIVE

SWITCHED LIVE (BLUE) MUST HAVE BROWN SLEEVE

TO LIGHT

4-WAY JUNCTION BOX

NEUTRALLIVE

EARTH

LCOM

L1 L2

LCOM

L1 L2

LCOM

L1 L2

LCOM

L1 L2

LCOM

L1 L2

LCOM

L1 L2

LCOM

L1 L2

DIMMER SWITCH

(BACK BOX MIN. DEPTH 25MM) (BACK BOX MIN. DEPTH 25-35MM*)

*dependant on wiring conditions

SQUARE EDGE INSTRUCTIONS.indd 1 19/02/2018 11:27