Riva RC4602SV-7416A-30 Installation guide

www.rivatech.de

Specification subject to change without notice

RC4602SV-7416A-30

Installation Guide

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A 2

Precautions & Notes

 Please read this manual carefully before installing the unit.

 Never disassemble the camera. Unauthorized disassembly may cause equipment failure

or damage to the unit.

 Please do not install the camera in a place exposed to direct sunlight.

 Do not operate the camera in environments beyond the specified temperature.

Refer to Environment Condition on APPENDIX (A): SPECIFICATIONS in this manual.

 Before applying power to the camera, check the power source to ensure that it is within

the specifications. Refer to Electrical Characteristics on APPENDIX (A):

SPECIFICATIONS.

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 3

Table of Contents

Precautions & Notes ................................................................................................. 2

1. FEATURES ............................................................................................................. 5

2. PACKAGE CONTENTS............................................................................................. 6

3. PART NAMES ........................................................................................................ 7

4. INSTALLATION ...................................................................................................... 8

4.1. Installing the camera .......................................................................................................... 8

Installation without bracket .................................................................................................. 8

Wall Mount ......................................................................................................................... 10

Wall / Corner Mount ........................................................................................................... 11

Wall / Pole Mount ............................................................................................................... 14

Ceiling Mount ...................................................................................................................... 18

4.2. Adjusting angle of the camera ......................................................................................... 19

4.3. Adjusting zoom and focus ................................................................................................ 19

4.4. Setting the Image Attribute ............................................................................................. 19

5. CONNECTIONS .................................................................................................... 20

6. CONFIGURATION ................................................................................................ 23

6.1.Set up network environment ............................................................................................ 23

6.1.1. Generic IP Environment ............................................................................................ 23

6.1.2. Custom IP Environment............................................................................................. 24

6.2. View video on web page .................................................................................................. 26

6.2.1. ActiveX Installation .................................................................................................... 26

6.2.2. View video using IPAdmin Tool ................................................................................. 27

6.3. Reboot .............................................................................................................................. 28

6.4. Factory Default ................................................................................................................. 28

6.5. Safe Mode ........................................................................................................................ 29

APPENDIX (A): SPECIFICATIONS .............................................................................. 31

Summary ................................................................................................................................. 31

Electrical Characteristics ......................................................................................................... 32

Environment Condition ........................................................................................................... 32

Mechanical Condition ............................................................................................................. 32

APPENDIX (B): POWER OVER ETHERNET ................................................................. 33

Power Comparison .................................................................................................................. 33

APPENDIX (C): DIMENSIONS ................................................................................... 34

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 4

APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE ................................. 35

REVISION HISTORY ................................................................................................. 36

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 5

1. FEATURES

Camera

 Sony STARVIS Exmor 1/2.8” 1080p CMOS Image Sensor

 True Day/Night

 Auto Iris Lens

 WDR

 30x Optical and 12x Digital zoom

 Weather Proof (IP66)

 Vandal Proof (IK10)

Video

 H.264 Baseline, Main, High profile (MPEG-4 Part 10/ AVC), MJPEG(Motion JPEG)

 Max 30fps in 1080p

 Text Overlay

Audio

 Two-way Audio Streaming

 G.711 µLaw

Network

 10/100 Base-T Ethernet

Integration

 Software Development Kit (SDK) available

 ONVIF Compliant (Profile S & Profile G)’

General

 microSD/SDHC slot

 Power Over Ethernet (PoE+)

Video Contents Analytics (VCA)

 VCA Presence (Standard)

* Licenses with higher specifications than VCA Presence are optional.

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 6

2. PACKAGE CONTENTS

Unpack and handle the equipment with care. The packaging contains:

Camera

Quick Installation Guide

Terminal Blocks

Ferrite Cores

Note

i

The contents above are subject to change without prior notice.

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 7

3. PART NAMES

① 3-Pin terminal block connector

For power connection (AC, FG, AC)

② Audio microphone stereo jack connector

Connector for RCA audio jack

③ Audio speaker stereo jack connector

Connector for RCA audio jack

④ 8-Pin terminal block (Digital Input)

Interface connector (IN4, IN3, GND, IN2, IN1, GND,

485+, and 485-). Please note that the terminal

block is used only for the digital input connection.

⑤ 6-Pin terminal block (Digital Output)

Interface connector (2N.O, COM2, 2N.C, 1N.O,

COM1, 1N.C)

⑥ LAN connector

RJ45 LAN connector for 10/100 Base-T Ethernet.

(PoE+ supported)

⑦ 32-pin slot

Main socket for 32-pin connector on PCB.

⑧ microSD/SDHC slot

Supports up to 32GB. Recommend Class 4 and

higher for HD recordings.

⑨ Reset button

Use the button to restart the device or to reset it to

Factory Default. Refer to 6.3. Reboot and

6.4. Factory Default for more details.

②

③

⑤

* Models and their appearance are subject to change without any prior notice.

④

①

Top View of PCB

⑦

⑥

Top View of

Camera’s Main Body

⑧

⑨

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 8

4. INSTALLATION

4.1. Installing the camera

Installation without bracket

LAN cable

Power cable

Audio cable

DI/DO cable

1) Loosen the three screws on the top of the

camera, and detach the safety ring from the top.

2) Twist the top of the camera counter-clockwise to

separate it from the main body, and push the lever

of the plastic cover at the bottom of the top

outward to open it. Then, insert the provided

terminal blocks to the corresponding places on the

PCB by reference to the image on the previous

page.

3) Drop all the necessary cables through the neck of

the camera’s top, and fix the top to your installed

bracket or on the designated spot.

4) Install the provided ferrite cores on the cables by

winding cables around the ferrite cores once. Refer

to the image on the left.

5) Connect all the cables to corresponding

connectors by reference to the image on the

previous page. Then, close the PCB on the top of the

camera.

6) Hook the safety ring to the top of the camera

while carefully holding the camera's main body, and

align the triangle marks on the top with the main

body.

7) Twist the main body counter-clockwise once the

camera’s top and the main body are properly

aligned, and tighten the three screws on the top.

Caution

!

Install the device after removing the bubble wrap inside the dome cover.

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 9

Note

i

The internal heater and fan do not work when the device is powered via PoE.

Caution

!

To prevent products from damage, place the camera on stable and non-vibrating

surfaces. If the stability is in doubt, consult safety personnel for reinforcements,

and then proceed with the installation.

Caution

!

Sealing gaps is recommended as gaps may appear after the camera installation.

Gaps may cause problems such as moisture, water leakage, and etc., which

negatively affect the operation of the camera if gaps remain unsealed.

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 10

Wall Mount

Model Name

WMB-4600

Contents

Installation

Wall Mount Bracket

Washer Based Self-Drilling Screw 4x32

4EA

1) Drill four holes for screws and one bigger hole for cables on the wall based on the screw

holes of the wall mount bracket.

2) Insert the four plain washers (M6) into the washer based self-drilling screws, and place the

wall mount bracket to the wall by aligning the bracket’s screw holes with the drilled holes on

the wall.

3) Insert the screws prepared in Step 2 into the drilled holes on the wall through the

bracket’s screw holes, and tighten the screws.

3) Refer to the section, Installation without bracket on the previous page for the rest part of

the installation.

PL A I N W A S HE R

WASHER BASED SELF-

DRILLING SCREW

Plain Washer M6

4EA

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 11

Wall / Corner Mount

Model Name

WMB-4600

CMA-4600

Contents

WMB-4600

CMA-4600

*Plain washer M8 is applied to be installed with WMB-4600.

Corner Mount Adaptor

Washer Based Self-Drilling Screw 4x32

8ea

PH M8x16L Bolt 4ea

Plain Washer M6

8ea

Plain Washer M8 4ea

Wall Mount Bracket

Washer Based Self-Drilling Screw 4x32

Flat Washer M6

4ea

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 12

Installation of the corner mount adaptor

PLAIN WASHER M6

WASHER BASED SELF-DRILLING SCREW

1) Drill four holes on the installation surface based on the screw holes of each side of the

corner mount adaptor.

2) Insert the plain washers (M6) into the screws.

3) Place the corner mount adaptor to the installation surface by aligning the screw holes

with the drilled holes on the installation surface.

4) Insert the screws into the drilled holes through the screw holes on the adaptor, and

tighten the screws.

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 13

Combination of wall mount bracket and corner mount adaptor

PLAIN WASHER

1) Insert plain washers into the PH M8x16L bolts.

2) Attach the wall mount bracket to the corner mount adaptor aligning the holes on both

brackets.

3) Insert the bolts prepared in Step 1 into holes on the corner mount adaptor through the

wall mount bracket, and firmly tighten the bolts.

4) Refer to the section, Installation without bracket on page 8 for the rest part of the

installation.

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 14

Wall / Pole Mount

Model Name

WMB-4600

PMA-4600

Contents

WMB-4600

PMA-4600

Pole Mount Adaptor

PH M6x12L Bolt 4ea

SUS Band 2ea

Wall Mount Bracket

Washer Based Self-Drilling Screw 4x32

Flat Washer M6

4ea

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 15

Installation of the pole mount adaptor

1) Push each SUS band through the holes on

the pole mount adaptor like the image on the

left.

2) Encircle the pole with the SUS bands

attached on the pole mount adaptor.

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 16

3) Push each SUS band’s end through

the fastener’s hole located on the SUS

band’s head.

4) Fasten each SUS band by tightening

the screw on the fastener clockwise.

5) Fasten enough both fasteners and

check whether the bracket is firmly-fixed

on the pole.

FASTENER

HOLE

SCREW

FASTENER

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 17

Combination of wall mount bracket and pole mount adaptor

Caution

!

Sealing gaps is recommended as gaps may appear after the camera installation.

Gaps may cause problems such as moisture, water leakage, and etc., which

negatively affect the operation of the camera if gaps appear but remain unsealed.

1). Attach the wall mount bracket to the corner mount adaptor aligning

the holes on the bracket and the adaptor.

2) Insert PH M6x12L bolts into the holes on the corner mount adaptor

through the wall mount bracket, and firmly tighten the bolts.

3) Refer to the section, Installation without bracket on page 8 for the rest

part of the installation.

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 18

Ceiling Mount

Model Name

CMB-4600

Contents

Installation of the ceiling mount bracket

1) Drill four holes on the ceiling based

on the screw holes on the ceiling

mount bracket.

2) Insert the provided four flat

washers(M6) into the

screws(4x32).Then, attach the ceiling

mount bracket to the ceiling, insert

the screws into the holes on the

bracket, and tighten the screws.

3) Refer to the section, Installation

without bracket for the rest part of

the installation.

Ceiling Mount Bracket

Flat Washer M6

Self-Drilling Screw 4x32

Ceiling Mount Bracket

Washer Based Self-Drilling Screw 4x32

Flat Washer M6, 4ea

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 19

4.2. Adjusting angle of the camera

The device is a 360° rotating camera and it is fully controlled by the web user interface.

Refer to the provided webpage user’s manual for more details.

4.3. Adjusting zoom and focus

The device is equipped with the 30x optical zoom lens with the auto focus feature and it is fully

controlled by the web user interface.

Refer to the provided webpage user’s manual for more details.

4.4. Setting the Image Attribute

On the camera’s webpage, users can configure the image settings. The menu of the image

attributes is available at Video Appearance via the path, Setup > Video & Audio > Camera. The

following attributes can be adjusted: Brightness, Contrast, Saturation, Sharpness, and

Orientation. For more detailed information, refer to the provided webpage user's manual.

RC Series RC4602SV-7416A-30 Installation Guide

04-2017-A www.rivatech.de 20

5. CONNECTIONS

① Audio connection

The camera provides a mono audio input and output. Due to low audio output power, an

amplified speaker is recommended for enhanced sound (Refrain from connecting a headphone

or an earphone directly to the camera).

② Sensor (DI) connection

Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor like the

following figures. Settings can be done through the camera’s webpage.

Input voltage range: 0VDC minimum to 5VDC maximum, Max 10mA

Name

Descriptions

IN4

Alarm Signal Input 4

IN3

Alarm Signal Input 3

GND

Ground

IN2

Alarm Signal Input 2

IN1

Alarm Signal Input 1

GND

Ground

485+

Reserved

485-

Reserved

Caution

!

Do not exceed the maximum input voltage or relay rate.

Top View

②

③

⑤

* Models and their appearance are subject to change without any prior notice.

④

①

⑥

Page is loading ...

Riva RC4602SV-7416A-30 Installation guide

This manual is also suitable for

Riva RC4602SV-7416A-30 Installation guide

Related papers

Other documents