Kuryakyn 7397 User manual

Type
User manual
KRUSADER HORN COVER, GLOSS BLACK
7397
Page 1
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN
RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring the contents described herein may negatively affect product per-
formance and functionality or damage the product itself or the product to which it is being attached.
STEP 1 Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn
IGN OFF. Allow the engine and exhaust system to cool.
STEP 2 Set up a soft, sturdy work surface within arm’s reach of the motorcy-
cle.
STEP 3 Refer to PIC 1. Remove the existing horn assembly; disconnect the
wires.
STEP 4 Refer to PIC 1. Remove the two (2) flange head screws and bracket
from the horn assembly; save the screws, wire retainer, and bracket
for later use.
STEP 5 Refer to PIC 2. Use a small flat-blade screwdriver to remove the
speed clips from the existing horn cover; lift the tabs, then slide the
clip off of the cover; save the clips for later use.
STEP 6 Refer to PIC 2. Remove the nut and horn from the horn cover; save
the nut and horn for later use.
ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:
1 Krusader Horn Cover
2 1/4”-20 X 1/2” Socket Head Cap Screws
1 Installation Instructions
YOU WILL ALSO NEED:
Set of sockets and ratchet, set of hex wrenches, small flat-blade screwdriver
These installation instructions contain important information. Ensure that the end user receives this copy and is
aware of its importance for future use.
INSTALLATION MAY REQUIRE CON-
TACT WITH THE ENGINE AND EX-
HAUST SYSTEM; ENSURE THAT IT HAS
FULLY COOLED BEFORE BEGINNING
TO PREVENT INJURY.
7397-11HD-0715
Thank You For Choosing Küryakyn!
Protect yourself and others from potential injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices
regarding the installation, use, and care of this product.
PIC 1
DISCONNECT WIRES
REMOVE HORN ASSEMBLY
PIC 2
LIFT TAB, THEN SLIDE OFF
REMOVE NUT AND HORN
Page 2
STEP 7 Install the two speed clips on the new cover bracket as shown in PIC 3. Ensure that
the clips are flat side up; note that the larger “ear” is the top of the bracket.
STEP 8 Refer to PIC 4. Attach the horn to the new bracket with the existing nut; leave it loose for now.
STEP 9 Refer to PIC 4. Ensure that the wire retainer is installed as shown using the top screw to secure it;
attach the existing bracket to the new bracket with the two (2) existing flange head screws. Leave
the screws loose for now.
STEP 10 Refer to PIC 5. Attach the horn assembly to the Krusader Horn Cover with the included 1/4”-20
Screws.
STEP 11 Align the horn in the Cover so it will not contact the Cover; tighten the nut.
Align the Bracket with the Cover so it is straight; ensure that the wire retainer remains aligned as
shown in PIC 5; tighten the flange head screws.
STEP 12 Reconnect the wiring; secure it in the wire retainer; attach the Krusader Horn Cover to the
motorcycle with the existing fastener.
PIC 4
ATTACH HORN WITH NUT;
ATTACH BRACKET WITH SCREWS;
ALIGN WIRE RETAINER
PIC 5
ATTACH ASSEMBLY TO KRUSADER COVER
WITH 1/4-20 SCREWS
PIC 3
SLIDE SPEED CLIPS ONTO
BRACKET, FLAT SIDE UP
TOP
PIC 6
ALIGN AND ATTACH
WITH EXISTING
FASTENER
Page 3
It is the end user’s responsibility to ensure that all fasteners (including pre-assembled) are tightened before
operation of the motorcycle. Kuryakyn will not provide warranty coverage on products or components lost or
damaged due to improper installation or lack of maintenance. Periodic inspection and maintenance are
required on all fasteners.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Kuryakyn 7397 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI