FOAMit FI-10N is a portable foam equipment capable of producing a foam stream of 15 to 30 gallons per minute. It can be used with various cleaning chemicals, including alkaline and caustic cleaners, and acids. The device is easy to operate and maintain, and it comes with a 20-foot reinforced hose and a discharge wand. With its sturdy construction and reliable performance, FOAMit FI-10N is an ideal choice for a wide range of cleaning applications.
FOAMit FI-10N is a portable foam equipment capable of producing a foam stream of 15 to 30 gallons per minute. It can be used with various cleaning chemicals, including alkaline and caustic cleaners, and acids. The device is easy to operate and maintain, and it comes with a 20-foot reinforced hose and a discharge wand. With its sturdy construction and reliable performance, FOAMit FI-10N is an ideal choice for a wide range of cleaning applications.
USER
MANUAL
MODEL NUMBER:
FI-10N
FI-10NK
FI-10NV
FI-10N-ST
FI-10NK-ST
FI-10NV-ST
AND RELATED UNITS
10 Gallon Air Operated Portable Foam
Equipment
English (Original Instrucons)
Page 2 of 6 | 06292015
User Manual: Rotomolded Portable Foam Units | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model No.: FI-10N, FI-10NK, FI-10NV, FI-10N-ST, FI-10NK-ST, FI-10NV-ST
Specicaons:
Hose .......... 20 feet reinforced hose, 1/2 inch inside diameter
(6 meters reinforced hose, 12.7 mm inside diameter)
Foam Output.................................. 15 to 30 gallons/minute
(57 to 144 liters/minute)
Foam Distances ............................. 15 to 20 feet (4.6 to 6 meters)
Liquid Temperature ....................... 40˚F to 100˚F (4.4˚C to 37˚C)
Noise Level..................................... Average 79 dB(A)
Discharge Wand Vibraon Level ….. Maximum 2.5 m/s²
Dimensions:
Length ....................................... 19 in (483 mm) approximately
Width ........................................ 16 in (406 mm) approximately
Height ....................................... 41 in (1041 mm) approximately
Weight, including discharge hose and wand:
(Empty) ................................ 39 lbs (18 kg) approximately
(Full) ...................................... 138 lbs (63 kg) approximately
Requirements:
Compressed Air Pressure Requirements: Air regulator (R25)
factory set at 50 psi (3.4 bar). Operang range is 40 to 80 psi (3
to 5 bar) with 3.5 to 8 CFM (99.1to 227 l/min)
Chemical requirements: follow all instrucons from chemical
manufacturer.
Air Operated Double Diaphragm Pump Models Oered:
P56: Polypropylene body with Santoprene diaphragm
P56V: Polypropylene body with Viton diaphragm
P56K: Polypropylene body with Kalrez diaphragm
Acceptable Products:
Alkaline cleaners, Causc cleaners, and Acids
* D-Limonene may only be used with Kalrez pump
* Chlorine may only be used with Viton or Kalrez pump
DO NOT USE: All hydrocarbons
Read this manual completely and understand the
machine before operang or servicing it.
• Always wear protecve clothing, gloves, and eyewear
while operang or servicing unit.
• Avoid contact of cleaning agent with skin and eyes.
If contact occurs, see SDS sheet for further rst aid
measures.
• Read chemical’s Safety Data Sheet (SDS) before using this
unit.
• Never point the discharge wand at anyone.
• Incoming air pressure cannot exceed 100 psi (7 bar).
• Aer each use, relieve all remaining pressure in the
system by unplugging the air line from the unit and
opening the discharge ball valve to prevent accidental
discharge.
• Aer relieving the pressure from the unit, store the unit
with the ball valve in the closed posion.
• Be sure to ush the unit with fresh water for 5 minutes
when switching from an alkaline to an acid or an acid to
an alkaline.
• Do not exceed a uid temperature of 100˚F (37˚C).
• Only use clean and dry air. Air must be ltered and free
of moisture or pump life will be diminished. If needed,
install an air dryer before unit.
• Do not use air lubricator before the unit.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials, old machine
components, and hazardous uids in an environmentally safe
way according to local waste disposal regulaons.
Always remember to recycle.
*Specicaons and parts are subject to change without noce.
WARNING
Page 3 of 6 | 06292015
User Manual: Rotomolded Portable Foam Units | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model No.: FI-10N, FI-10NK, FI-10NV, FI-10N-ST, FI-10NK-ST, FI-10NV-ST
Operaon Instrucons:
1. Follow all instrucons from chemical manufacturer.
Fill the tank with water and the advised percentage of
chemical concentrate.
2. With ball valve (HV60) in the closed posion, plug an air
line into the air ng (AP25).
3. Slowly open the ball valve (HV60) completely.
4. Adjust the needle valve (NV14Y) to desired wetness or
dryness of foam following the steps below:
a. Close needle valve completely in clockwise direcon.
b. Open needle valve in counter-clockwise direcon 3
complete turns.
c. Connue to open valve in ¼ turn increments allowing
30 seconds between adjustments unl proper
consistency of foam is achieved.
Aer Use Instrucons:
1. Flush the unit with fresh water for 5 minutes.
2. Disconnect the air line from the air ng (AP25) and
relieve any remaining pressure in the system by opening
the discharge ball valve (HV60).
3. Close the ball valve (HV60) aer all pressure has been
relieved from the system.
Maintenance Instrucons:
To keep your portable tank foamer operang properly,
periodically perform the following maintenance procedures:
• Check the air pump (P56/P56K/P56V) for wear and leaks.
• Inspect hoses for leaks or excessive wear. Make sure all
hose clamps are in good condion and properly secured.
• Replace lter (AFR25) in regulator (R25) as needed.
• Check the sucon tube and screen for debris and clean as
needed.
• Drain compressor tank on a regular basis to ensure proper
operaon of pump.
Troubleshoong Instrucons:
• Check to ensure the discharge hose is uncoiled properly,
and that there are no kinks that could obstruct uid ow.
• Check air regulator bowl (ABR25) for debris such as
water, oil, or rust parcles. Clean by unthreading the air
regulator bowl from the air regulator (R25).
• If needle valve (NV14Y) valve is open too far, the pump
(P56/P56K/P56V) will cycle improperly due to lack of air
pressure. If this occurs, reset needle valve as described in
Operaon Instrucon #4.
• Make sure proper foaming chemical and concentraon is
being used.
• If air passes through the pump (P56/P56K/P56V) without
cycling, the pump needs to be replaced.
• If foam soluon backs up into air regulator bowl (ABR25),
the check valve (CV38) needs to be replaced.
• If foam comes out wet, no maer where the needle valve
(NV14Y) is posioned, the check valve (CV38) may need to
be replaced.
• Check for proper air pressure on air gauge (AG100). Air
regulator (R25) is factory set at 50 psi (3.4 bar). Operang
range is 40 to 80 psi (3 to 5 bar) with 5 to 10 CFM (141.64
to 283.30 l/min)
• If the unit foams at a reduced pressure:
o Check the air compressor supplying the unit. If the
pressure is less than 40 psi, turn the foam unit o
unl the compressor can catch up.
o If the air supply is 50 psi (4.14 bar) or above, check
the AG100, which should read near 50 psi (4.14 bar).
If the AG100 is more or less than 50 psi (4.14 bar),
adjust the pressure by turning the knob on the top
of the air regulator (R25).
o If both of the above are okay, the stainless steel
mixing mesh (SS-MESH) could be plugged. Remove
and clean it by following the instrucons below:
1. Be sure the foam unit is not plugged into an
air supply and be sure to relieve all stored
pressure in the unit by having the ball valve
(HV60) in the open posion.
2. Remove the stainless adaptor (HBSS1234) from
the tee ng (SST12HB38).
3. Remove the screen and the mixing mesh from
inside the tee ng (SST12HB38).
4. Clean any parcles from the mixing mesh and
the screen.
5. Replace the mixing mesh and then the screen
into the back of the tee and screw the stainless
adaptor back into the tee. It is recommended
to use a pipe thread sealant when reinstalling
the stainless adaptor back into the tee ng
(SST12HB38). If the mixing mesh has a lot of
foreign parcles in it, make sure the strainer
(STR38-IL) is sll in place.
• Check for plugged strainer (STR38-IL). Replace strainer if
necessary. Strainer must be used.
Page 4 of 6 | 06292015
User Manual: Rotomolded Portable Foam Units | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model No.: FI-10N, FI-10NK, FI-10NV, FI-10N-ST, FI-10NK-ST, FI-10NV-ST
HBSS1212 HV60 SN1212 PW10 ST80100
SSP12
SSAXLE14
AS1-VS
W15
FWAX15
PVCV34FM
COT
TANK-10N
DFP7
(see parts list
for color opons)
DP-A
TANK ASSEMBLY
ITEM NUMBER: TANK-10N-A
HOSE AND WAND ASSEMBLY
ITEM NUMBER: SSWA12-HA20
HBSS1212 HV60 HHSB1214 W8
ZERO TIP FOAM WAND ASSEMBLY
ITEM NUMBER: SSWA12 20 (6 m) HOSE ASSEMBLY
ITEM NUMBER: H12-20
FAN TIP FOAM WAND ASSEMBLY
ITEM NUMBER: PWA12-ST
ANTI-KINK SPRING ASSEMBLY
ITEM NUMBER: AKSS12
Page 5 of 6 | 06292015
User Manual: Rotomolded Portable Foam Units | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model No.: FI-10N, FI-10NK, FI-10NV, FI-10N-ST, FI-10NK-ST, FI-10NV-ST
NV14Y
SSA14
AP25
FWP12
HBSS1212
PLATE ASSEMBLY
ITEM NUMBER (Santoprene pump): PA-PF12
ITEM NUMBER (Kalrez pump): PA-PF12K
ITEM NUMBER (Viton pump): PA-PF12V
P56-BRKT-SCREW
HBSSEL1438
NV14Y
HBSS1438
SSC38EC14-2
SSC38
P56, P56K, or P56V
HBSSEL1814
P56-BRKT
R25
SST12HB38
HBSSEL1438
AG100
CV38
Plate - Inside View
Plate - Back View
HHPB3414
STR38-IL
HBSSEL1438
SSC38
BPS-58SO
PVCV34FM
BPS-58SO
OPTIONAL COMPONENTS
WATER SEPARATOR
ITEM NUMBER: WS-20CFM
30 (9 m) AIR HOSE ASSEMBLY
ITEM NUMBER: AH30
Page 6 of 6 | 06292015
User Manual: Rotomolded Portable Foam Units | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model No.: FI-10N, FI-10NK, FI-10NV, FI-10N-ST, FI-10NK-ST, FI-10NV-ST
ITEM NUMBER DESCRIPTION
AG100 1.5 INCH DRY MODEL 20 DUAL SCALE GAUGE
AKSS12 SS ANTI-KINK SPRING FOR 1.2 INCH HOSE WITH PIN
AKSS12-P SS ANTI-KINK SPRING FOR 1.2 INCH HOSE
AKSS-HPC ANTI-KINK STAINLESS STEEL HITCH PIN CLIP
AP25 PLUG 1/4 NPTM AIR FITTING - BRASS
AS1-VS 1/4-20 X 1/2 PHIL TRUSS MACH SCREW 19-8 W/516
ORANGE VIBRASEAL PATCH
B8X58 8-15 X 5/8 inch PHIL FLAT TY-A 316 S.S.
BPS-58SO Back Panel Screw - 5/8 inch with Stand O
BPS-SSR 1/4 INCH PUSHNUT BOLT RETAINER STAINLESS STEEL
COT 1/8 X 1 COTTER PIN 18-8 S/S
CV38 PVC CHECK VALVE 3/8 BARBS - SS SPRING
DFP7 7 INCH HINDGED CAP INCLUDES LID FLANGE AND HINGE
PIN
DFP7-C 7 INCH DRAIN CAP POLYPRO BLACK
DFP7-F 7 INCH TANK LID FLANGE POLYPRO
DFP7-PIN HINGE PIN FOR DFP7-C & DFP7-C
DFP7-C-BL 7 INCH FILL CAP POLYPRO BLUE PANTONE
DFP7-C-GN 7 INCH FILL CAP POLYPRO GREEN PANTONE
DFP7-C-RD 7 INCH FILL CAP POLYPRO RED PANTONE
DFP7-C-YL 7 INCH FILL CAP POLYPRO YELLOW PANTONE
DP-A DRAIN PLUG ASSEMBLY FOR NATURAL PORTABLE UNITS
DP FRONT DRAIN PLUG FOR PORTABLE UNIT POLYPRO
DP-G FKM SQUARE CUT DRAIN PLUG GASKET
DP-INSERT 304 STAINLESS DRAIN PLUG INSERT
EC12 OETIKER CLAMP 21.0-706R
EC14-2 OETIKER CLAMP 13.8
F12SS STAINLESS .875 ID FERRULE FOR 1/2 INCH HOSE
F38SS STAINLESS 3/8 INCH FERRULE
FACI14 FEMALE COUPLER - 1/4in NPTF
FWAX15 FLAT AXLE WASHER
FWP12 7/8 ID X 1.5 OD X 0.05 THK SSFW
FWP14 C-816 1/2in SS WASHER
H12B-H 1/2 INCH BLUE HOSE - Available per .
H14B-H 1/4 INCH BLUE HOSE- Available per .
H38B-H 3/8 INCH BLUE HOSE - Available per .
HBBF1438 BRASS 1/4in FPT X 3/8in HOSE BARB
HBSS1212 STAINLESS HOSE BARB 1/2 X 1/2
HBSS1438 STAINLESS HOSE BARB 1/4 MPT X 3/8 BARB
HBSSEL1438 STAINLESS HOSE BARB ELBOW 1/4 INCH NPT X 3/8 HOSE
BARB
HBSSEL1814 304 STAINLESS ELBOW 1/8 INCH NPT X 1/4 INCH HOSE
BARB
HHPB3414 HEX HEAD POLY REDUCER BUSHING 3/4 X 1/4
HHSB1214 HEX HEAD S.S. REDUCER BUSHING 1/2 X 1/4
HV60 1/2in STAINLESS BALL VALVE - w/ WELDED NUT
NV14Y FLOW CONTROL VALVE - INCLUDES BLACK KNOB
NV14Y-HNDL KNOB FOR 2839-1/4 NEEDLE VALVE
P56 5700 PUMP WITH SANTOPRENE SEALS - INCLUDES HOSE
BARBS
P56K 5700 PUMP WITH KALREZ SEALS - INCLUDES HOSE BARBS
P56V 5700 PUMP WITH VITON SEALS - INCLUDES HOSE BARBS
20756103B Polypro G57 Air Port x HB Straight, w/ Viton o-ring
HB14P 1/4in BRASS HB AIR FITTING /G57/P56
HB5638 HOSE BARB FOR P56 PUMP
HB5638K HOSE BARB FOR P56K PUMP
HB5638V HOSE BARB FOR P56V PUMP
P56-BRKT PUMP BRACKET- STAINLESS STEEL
P56-BRKT-SCREW HI LO SCREW FOR RETAINING P56-BRKT
PLPF PORTABLE FOAMER BACK PLATE W/ HINGE AND HOLES
PLPF-PIN 302 STAINLESS PORTABLE PLATE HINGE PIN
PVCV34FM PVC VALVE 3/4in FPT X 3/4in MPT
PW10 3/4in BLACK POLY PRO X 10in - FPTBE - SCH.80
R25 AIR REGULATOR INCLUDES AIR FILTER AND BOWL
AFR25 AIR FILTER for R25
ABR25 METAL AIR BOWL for R25
S142058-VS 1/4-20 X 5/8 PHIL TRUSS MACHINE SCREW 18-8 W/#516
VIBRASEAL ORANGE PATCH
SN1212 1/2in HEX STAINLESS STEEL NIPPLE
SSA14 SS304 MALE/FEMALE ADAPTOR 1/4 NPT X 1/4 NPT
SSAXLE14 14 ½” long with the 5/8” diameter bar & 2 through holes
with countersinks beveled ends
SSC12 WORM GEAR CLAMP, S/S (.31-.91)
SSC38 WORM GEAR CLAMP, S/S (.25-.63)
SS-MESH STAINLESS STEEL MESH WITH SSST FOR REPLACEMENT
SSP12 STAINLESS STEEL AXLE PLATE - 2.5 inch X 1 inch - 2 HOLE
SSST SCREEN DISC .687 DIA. 10 X 10 MESH @ .020 DIA. 300
SERIES S.S.
SST12HB38 STAINLESS TEE COMBO 1/2in FPT X 3/8 in BARB WITH
SSST AND S.S. MESH
ST80100 VEEJET NOZZLE, BRASS 80100
STR38-IL IN LINE STRAINER 3/8 BARB 20 MESH 304 STAINLESS
EDPM GSKT
TANK-10N 10 GALLON NATURAL TANK
TW916 1/2 INT TOOTH L/W 410SS
W15 NONMARKING WHEEL FOR PORTABLE UNITS
W8 1/4in S.S. WAND 7IN SS TOE
-
1
-
2
-
3
-
4
-
5
-
6
FOAMit FI-10N is a portable foam equipment capable of producing a foam stream of 15 to 30 gallons per minute. It can be used with various cleaning chemicals, including alkaline and caustic cleaners, and acids. The device is easy to operate and maintain, and it comes with a 20-foot reinforced hose and a discharge wand. With its sturdy construction and reliable performance, FOAMit FI-10N is an ideal choice for a wide range of cleaning applications.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Innovative Cleaning Equipment FI-10NK-SM User manual
-
Nilfisk FI-30N User manual
-
Ecolab SP-10N-MOBYSPRAY User manual
-
Ecolab PTF-NVS-2 Wall Mounted Pneumatic Teat Foam System and Applicator User manual
-
Nilfisk FOOD DFA-TR7 User manual
-
Bestway Field Pro III 1600 User manual
-
Spartan 738 SM User manual
-
ANTEK ECE10CM Series Technical Documentation Manual
-
Pentair Berkley MGPS7C3-575T User guide
-
Smithco Spray Star 1200 Owner's manual
