2. Computers & electronics
  3. Cameras & camcorders
  4. Camera accessories
  5. ADEMCO
  6. RapidDome
RapidDome

ADEMCO RapidDome Owner's Installation Manual

  • Hello! I am an AI chatbot trained to assist you with the ADEMCO RapidDome Owner's Installation Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Document Number - AVRPDMAN190701E
RapidDome (24V AC)
Owners Installation Guide
Sales: .................................... 800-467-5875
Applications ......................... 877-653-0302
Technical Support ................ 800-645-7492
Fax........................................ 516-921-4307
Web site................................ www.ademcovideo.com
Owners Installation & Operation Guide RapidDome
© Ademco Video 2001 AVRPDMAN190701E Page i
Table of
Contents
Safety Instructions
ii
Introduction to the RapidDome
1
1 Setting up the RapidDome
4
1.1 Wiring Details
4
1.2 Settings on the RapidDome Top Board (VC445V3)
7
1.3 Setting Protocols (Ademco Video & Pelco)
8
1.4 Coax Control
10
1.5 LED on the RapidDome Bottom Board (VC444/3)
11
1.6 Alarm / Relay Connections
12
2 Installing the RapidDome
14
2.1 Installation Process
14
3 Technical Specifications
21
Appendix A. Typical System Diagrams
26
A. Individual Twisted Pair Output
26
B. Twisted Pair and ’daisy chain’ connections
26
C. Star Connections
27
RapidDome Installation & Operation Guide
Page ii © Ademco Video 2001 AVRPDMAN190701E
Safety
Notes
Safety Instructions
WARNING! Read these notes before
attempting to operate the RapidDome
Refer all servicing to qualified personnel.
These products are for internal use only.
These products contain static electricity sensitive devices. Please take
appropriate precautions when handling.
Handle the RapidDome with care, as improper handling may cause ir-
reparable damage to the precision or sensitive parts within this unit.
Never point the camera directly towards a bright light source (for ex-
ample sunlight), or expose the camera to intensive light situations as
this may damage the camera pick-up device.
This information and our technical advice - whether verbal, in writing,
or by way of trials - is given in good faith but without warranty and
this also applies where proprietary rights of third parties are involved.
Our advice does not release you from your obligation to check its va-
lidity and to test our products suitability for the intended purpose(s)
and use(s). The application, use and installation of our products either
in isolation or in conjunction with other products used, provided and/
or installed by you on the basis of our technical advice are beyond our
control and therefore remain entirely your own responsibility.
Ademco Video products are sold in accordance with our General
Conditions of Sale and Delivery.
ALL DESIGNS AND SPECIFICATIONS ARE
SUBJECT TO CHANGE WITHOUT NOTICE
© Ademco Video 2001
Installation & Operation Guide RapidDome
© Ademco Video 2001 AVRPDMAN190701E Page 1
Introduction
Introduction to the RapidDome
ADEMCO Video’s RapidDome™ is a cost-effective, superior quality
internal dome that features a high-resolution, low-light sensitive color
camera in a high-speed pan/tilt/zoom dome assembly. Ideal for the
vast majority of indoor installations, RapidDome provides sharp,
detailed images down to 1.0 lux through advanced digital signal
processing, continuous autofocus and a 24X total zoom capability
(12X optical, 2X digital). RapidDome is the perfect complement to
ADEMCO Video’s Orbiter indoor and environmental domes that
feature extended zoom capacity, even lower light sensitivity and a
high-speed color/mono changeover camera option.
RapidDome features an intelligent zoom that automatically adjusts
pan and tilt speeds in proportion to zoom position. The dome provides
360° continuous pan rotation and manual variable speed control at
0.1-100°/second. Because of its attractive compact design and with its
low profile (at only 5"), the RapidDome makes the perfect choice for
applications where aesthetics are critical.
RapidDome is available in two standard dome assemblies; a false
ceiling mount and a plug and play pendant. The false ceiling version
provides quick and easy installation into any drop or false ceiling, no
additional mounts or accessories are required. The standard pendant
version provides the ultimate in flexibility. Its plug and play receptacle
gives you the freedom to choose the right RapidDome mounting
accessory for your installation.
• Compact low profile design at only 5”
• High resolution low light camera
• (460TVL, 1.0 lux)
• Digital Signal Processing (DSP)
• Automatic digital backlight compensation
• 24X zoom (12X optical, 2X digital)
• Continuous auto focus and auto iris with manual
overrides
RapidDome Installation & Operation Guide
Page 2 © Ademco Video 2001 AVRPDMAN190701E
Introduction
• Intelligent zoom automatically adjusts pan and tilt
speeds in proportion to zoom position.
• 360° continuous rotation
• Automatic 180° flip circuitry
• 64 presets and 3 tours
• 8 alarm inputs and 2 alarm output relays resident in the
dome.
• Built-in intelligent receiver for up-the-coax (UTC) or
RS485 twisted pair (TP) operation
• Built-in code translator provides compatibility with
PELCO P or D based systems
• Automatic vertical sync-phase adjustment
• Easy installation and servicing:
RapidDome’s pendant version features an innovative“plug and play”
design that makes installation and servicing quick and convenient.
• High resolution, low light camera:
RapidDome’s high resolution DSP color camera and low light
sensitivity (1.0 lux) makes it ideal for the vast majority of indoor
installations.
• Continuous auto focus with manual override:
No matter what the zoom position, RapidDome’s images remain in
sharp focus. When the scene requires extra fine control, RapidDome
allows the operator to overrride the auto focus settings.
• Intelligent zoom:
RapidDome automatically adjusts pan and tilt speeds in proportion to
zoom position for greater control. The lens pauses at 12X
magnification, then enters digital zoom mode up to 24X.
• Continuous rotation, high-speed pan, tilt, and zoom systems:
RapidDome features 360° continuous rotation on gold slip rings.
RapidDome also features high-speed precision control with electronic
braking for up to 300°/second operation down to 0.1°/second.
Installation & Operation Guide RapidDome
© Ademco Video 2001 AVRPDMAN190701E Page 3
Introduction
• 180° flip ON/OFF
When this feature is ON, RapidDome automatically turns 180° when
reaching its lower tilt limit. This allows the operator to continuously
track objects moving directly below the camera.
• Preset positioning, alarm activation, and tour capabilities:
RapidDome presets can easily be set up and recalled by the operator
when using ADEMCO Video RapidView systems. Three tours may be
programmed. Each of RapidDome’s alarm inputs automatically call a
preset when an alarm is activated. Two alarm outputs can be used to
control external devices.
• Up-the-coax or RS485 twisted pair operation
(system dependent):
Up-the-coax operation of up to 1,000 feet (300 meters) is possible with
appropriate cable. RS485 twisted pair operation allows up to 32
RapidDomes to be daisy chained at a maximum of 5,000 feet (1500
meters).
• Automatic sync-phase adjustment:
Using compatible RapidView Matrix systems, the video signal can be
synchronized with other system inputs with the touch of a button.
RapidDome Installation & Operation Guide
Page 4 © Ademco Video 2001 AVRPDMAN190701E
Chapter 1
1. Setting up the RapidDome
1.1 Wiring Details
1.1.1 Mounting
The RapidDome is designed for speed of installation and set up and so
the wall and ceiling mount brackets are supplied pre-wired. Customer
wiring is via an internal terminal block PCB which is located inside
the base plastic cover. (See Figure 1 for the location of the terminal
block and for the wiring details.)
The false ceiling versions of the RapidDome are supplied with a 3m
cable. (See Figure 2 for the wiring details.)
Note: The terminal block is accessed by removing the two M3 CSK
head screws, using an appropriate tool. The location of the screws is
shown in Figure 1, below, by an ‘*’.
1.1.2 Wall & Ceiling Mount
Figure 1
Mountin g Opti ons for RapidDome
(including detail of the terminal block)
**
54mm
(2.13”)
82mm
(3.28”
)
42mm
(1.65”)
12mm WIDE
SLOT FOR
CABLES
ON R30
M5 OR No10 FITTINGS
WALL / CEILING MOUNT
WALL MOUNT BRACKET
AD5WBW
CEILING MOUNT
BRACKETS
AD5PB80
AD5PB300
AD5PB600
161mm
(6.34”)
142mm
(5.59”)
Installation & Operation Guide RapidDome
© Ademco Video 2001 AVRPDMAN190701E Page 5
Chapter 1
1.1.3 False Ceiling Mount
Figure 2
Wiring Details for the RapidDome (False Ceiling Mount)
Table 1
Terminal Block Wiring
TWISTED PAIR UP THE COAX (UTC)
SG (Not Used)
SG (Not Used)
SYN (Not Used) SYN (Not Used)
D+ Twisted Pair
Control
D+ (Not Used)
D-
D- (Not Used)
VID Video
Signal
VID Video
Signal
VG Video
Ground
VG Video
Ground
+V (AC) 24V AC
+V (AC) 24V AC
0V (AC) 24V AC 0V (AC) 24V AC
16
4
2
75
3
Solder side view of
socket fitted on 3 meter
(9.84 feet) cable supplied
From end of cable
RapidDome Installation & Operation Guide
Page 6 © Ademco Video 2001 AVRPDMAN190701E
Chapter 1
.
Table 2
RapidDome Socket Connector
TWISTED PAIR UP THE COAX (UTC)
Pin 1 Green
24V
AC
Pin 1 Green 24V
AC
Pin 2 Red
24V
AC
Pin 2 Red 24V
AC
Pin 3 Blue
Data + Pin 3 (Not
Used)
Pin 4 Yellow Data - Pin 4 (Not
Used)
Pin 5 Coax
Shield
Video
Ground
Pin 5 Coax
Shield
Video
Ground
Pin 6 Coax
Core
Video
Signal
Pin 6 Coax
Core
Video
Signal
Pin 7 (Not
Used)
Pin 7 (Not
Used)
Installation & Operation Guide RapidDome
© Ademco Video 2001 AVRPDMAN190701E Page 7
Chapter 1
1.2 Settings on the RapidDome Top Board (VC445V3)
In the following section, please refer to Figure 3 below, for the
locations on the board.
Figure 3
The VC445V4 RapidDome Board
LED D2
will illuminate if the receiver that is being controlled by
Coax control is selected by the transmitter and the coax control is
satisfactory. If the receiver is being controlled by twisted pair
control, LED D2 will flash whenever a valid control command is
received.
L
K
1
O
F
F
O
N
D2
DILSW1
- RapidDome
address setting
DIL Switch.
D2
- Coax Control OK LED
This LED is illuminated if the receiver is being
controlled by Coax control and is selected by the
transmitter. If the receiver is being controlled by
twisted pair, it will flash whenever a valid control
command is received.
LK1
- Twisted Pair Termination Link.
1-2 = Termination ON
2-3 = Termination OFF
T
E
R
MI
N
A
T
I
O
N
3
2
1
9&/
RapidDome Installation & Operation Guide
Page 8 © Ademco Video 2001 AVRPDMAN190701E
Chapter 1
1.3 Setting Protocols (Ademco Video & Pelco)
1.3.1 Selecting the Control Protocol
Using the last 2 poles of DIL Switch 1 on the RapidDome board (see
Figure 3) set the switches as shown in the table below
1.3.2 Address Settings
The addresses for each Dome are set as shown in the table below. Set
the Poles on DILSW 1 to the desired position for each address.
Table 3
Protocol Settings
Protocol DILSW1
Pole 7
DILSW1
Pole 8
AV O f f
Off
Pelco ‘p’
(4800 baud)
On
Off
Pelco ‘d’
(2400 baud)
Off
On
Installation & Operation Guide RapidDome
© Ademco Video 2001 AVRPDMAN190701E Page 9
Chapter 1
RapidDome Installation & Operation Guide
Page 10 © Ademco Video 2001 AVRPDMAN190701E
Chapter 1
1.3.3 Additional Features
The following RapidDome functions are implemented for use with the
Pelco protocol:
• Variable Speed Pan & Tilt.
• Zoom / Focus & Iris.
Digital Zoom is always enabled, but if controlled using AV protocol
and a controller, the controller can disable or re-enable digital zoom
via a menu.
• Auto Focus during pan / tilt or zoom. Auto Iris during pan and tilt.
Proportional maximum speed of pan and tilt is dependant on
zoom.
• 64 presets for pan / tilt / zoom / focus and iris. The presets are
numbered 1 - 32 and 35 - 66.
• Certain Presets for Special Functions:
33 Flip Command
34 Pan Zero
92 Left Scan Limit
93 Right Scan Limit
99 Auto (Continuous) Scanning
98 Frame Scanning
97 Random Scanning
96 Stop Scanning
95 Line Sync. Phase Adjustment
• 180° Flip ON/OFF.
• Auto seek alarms are enabled for pelco ’p’ and ’d’ protocols.
1.4 Coax Control
Coax control RapidDomes do not require an address setting, therefore
the settings of positions 1 - 7 on DILSW1 are ignored.
Installation & Operation Guide RapidDome
© Ademco Video 2001 AVRPDMAN190701E Page 11
Chapter 1
1.5 LED on the RapidDome Bottom Board (VC444/3)
In the following section, please refer to Figure 4, below, for the
locations on the board.
Figure 4
The RapidDome Bottom Board
LED D19
will flash each time a valid control command for this
receiver is received.
D19
- Data Received LED
Flashes whenever a
valid control
command is received
RapidDome Installation & Operation Guide
Page 12 © Ademco Video 2001 AVRPDMAN190701E
Chapter 1
1.6 Alarm / Relay Connections
The connections to the alarm inputs and relay output are via 2 RJ45
sockets located at the top of the RapidDome, shown in Figure 5,
below.
Figure 5
Top View of Jupiter with Alarms
The connections on the RJ45 plugs are numbered as shown in Figure
6. A suitable termination tool will be be required to connect to the
RJ45 plugs.
Figure 6
Contact Side View of RJ45 Plug
The 2 RJ45 connectors are wired as shown in the table overleaf.
Connector 3
Connector 2
1
8
Contacts
Cable
Installation & Operation Guide RapidDome
© Ademco Video 2001 AVRPDMAN190701E Page 13
Chapter 1
(N/O = Normally Open, N/C = Normally Closed.)
Note: Relay 2 is controlled by a RapidViews’ ‘0’ ‘AUX’ momentary
function and can be used to control auxiliary equipment.
Note: The maximum current rating for the 2 relays is 1A @ 24V DC
or 0.5A @ 120V AC
Table 4
RJ45 Connector
CONNECTOR 2 CONNECTOR 3
PIN SIGNAL PIN SIGNAL
White / Orange
1
Alarm in 1
1 Alarm in 5
Orange
2
Alarm in 2
2 Alarm in 6
White / Green
3
Alarm in 3
3 Alarm in 7
Blue
4
Alarm in 4
4 Alarm in 8
White / Blue
5
Alarm
Common
5 Alarm
Common
Green
6
Relay 1 N/O
6 Relay 2 N/O
White / Brown
7
Relay 1
Common
7 Relay 2
Common
Brown
8
Relay 1 N/C
8 Relay 2 N/C
RapidDome Installation & Operation Guide
Page 14 © Ademco Video 2001 AVRPDMAN190701E
Chapter 2
2. Installing the RapidDome
Note: When handling the RapidDome, DO NOT touch the acrylic,
or any sensitive or precision parts, as this will cause damage to the
unit.
2.1 Installation Process
2.1.1 Ceiling and Wall Mounted Models
Figure 7, below, details the ceiling and wall mount brackets, including
dimensions.
Figure 7
Mounting Brackets for RapidDome
54mm
(2.13”)
42mm
(1.65”)
12mm WIDE
SLOT FOR
CABLES
ON R30
M5 OR No10 FITTINGS
WALL / CEILING MOUNT
WALL MOUNT BRACKET
AD5WBW
CEILING MOUNT
BRACKETS
AD5PB80
AD5PB300
AD5PB600
161mm
(6.34”)
142mm
(5.59”)
82mm
(3.28”)
Installation & Operation Guide RapidDome
© Ademco Video 2001 AVRPDMAN190701E Page 15
Chapter 2
2.1.2
Instruction
Step 1 Attach the bracket (wall or ceiling type)
using fittings which are appropriate for
the surface and able to support the weight
of the RapidDome 1.11kg (2.4 Lbs).
Figure 8
Fitting the RapidDome into the bracket
Instruction
Step 2 Align the lug on the RapidDome with the
slot on the bracket. Carefully push the
RapidDome into the bracket and twist
clockwise. Allow to drop into the
retainer. See Figure 8 & Figure 9.
Figure 9
Fitting the RapidDome into the bracket
PUSH UP POLE –
ALIGN LUG TO SLOT
PUSH UP
TWIST
RapidDome Installation & Operation Guide
Page 16 © Ademco Video 2001 AVRPDMAN190701E
Chapter 2
2.1.3
Instruction
Step 3 Fit the M3 CSK safety locking screw into
the bracket to lock the RapidDome in
place. This is essential for the safe
operation of the RapidDome. The hole
for the screw is on the opposite side of the
pole to the slot.
Step 4 Attach the cable cover. This is supplied as
two halves which snap together over the
neck of the RapidDome as shown in
Figure 10, below.
Figure 10
Fitting the Cable Covers
Note: When the RapidDome is to be fitted to a mounting pole, then
the hole in the cable cover will need to be aligned with the screw hole
in the pole when fitting the M3 CSK safety locking screw as shown
in Figure 11.
Figure 11
Fitting the M3 CSK locking screw
FIT LOCKING
SCREW
ALIGN HOLE WITH
SCREW HOLE
Installation & Operation Guide RapidDome
© Ademco Video 2001 AVRPDMAN190701E Page 17
Chapter 2
2.1.4
The NPT Adapter allows the installation of plug and play extensions
for ceiling type mounts
Figure 12
AD5PBNPT - 1½" NPT to Plug & Play Adapter
Assembly Procedure
Instruction
Step 1 Isolate all cabling to the installation
electrically before proceeding
Step 2 Remove the connector from the Adapter
and pull sufficient cable from the
installation 1½" NPT female threaded
socket to work comfortably on. Make all
necessary electrical connections and
terminations to the connector, noting the
cable, connector and socket orientations.
See figure 13.
/